MiBoxer 8-Zone RGB+CCT Remote Controller

Product Features

This product adopts a world-wide used 2.4GHz frequency and GFSK control method. It features low power consumption, long-distance transmitting, strong anti-interference, and fast communication rates. It can control specified Mi-Light smart lights, allowing for changes in color, color temperature, saturation, and brightness.

Technical Parameters

• Model No.: E012024-MMF
• Voltage: 3V (AAA * 2PCS)
• Transmitting Power: 0 dBm
• Standby Power Consumption: 15uA
• Transmission Frequency: 2400-2483.5MHz
• Modulation Method: GFSK
• Control Distance: 10m
• Size: 153mm * 47mm * 19mm

Products Key Diagram

The remote controller features a color ring for color selection and saturation/CCT control. A brightness slider allows for brightness adjustment. There are buttons for Master ON/OFF, Zone ON/OFF, and Mode switching, along with speed control buttons (S- and S+).

Key Diagram Explanation:

• Color Ring: Touch the color ring to change colors. Under white light mode, it adjusts color temperature; under color light mode, it changes color saturation.
• Brightness Slider: Slide to adjust brightness.
• White Light Button: Press to get white light.
• ON Button: Touch to turn on the linked device.
• OFF Button: Touch to turn off the linked device.
• M Button: Dynamic mode switching button.
• S- Button: Lowers the dynamic mode speed.
• S+ Button: Accelerates the dynamic mode speed.
• Zone ON/OFF Buttons: Used to link/unlink devices to specific zones.

Grouping of Several Lights

An unlimited number of lights can be added to a zone on the 8-channel remote by linking them to different zones. This allows for flexible group combinations. The document provides examples of grouping.

Remarks:

• Users can reprogram as needed. One remote can control countless lamps or controllers, but one lamp or controller can only be controlled by a maximum of four remotes.
• Ensure correct battery installation and controller power status (fully discharged) when programming after switching off and on.

Linking & Unlinking

Lights can be used after linking with the remote controller.

Linking Instructions

1. Switch off the light, wait 10 seconds, and switch it on again.
2. When the light is on, short press any zone's ON button 3 times within 3 seconds.
3. If the light blinks slowly 3 times, the linking is successful.

If the light does not blink slowly, the linking failed. Switch off the light again and repeat the steps.

Unlinking Instructions

1. Switch off the light, wait 10 seconds, and switch it on again.
2. When the light is on, short press the Link/Unlink button 5 times within 3 seconds.
3. If the light blinks quickly 10 times, the unlinking is successful.

Unlinking must be performed on the same zone as the linking. If the light does not blink quickly, the unlinking failed. Switch off the light again and repeat the steps to unlink.

Attention

• The 8-zone remote controller is compatible only with specified Mi-Light products. Not all Mi-Light series products will work with this remote.
• If the indicator light blinks quickly during use, replace the batteries promptly.
• Avoid using poor quality batteries, as leaking battery fluid can damage the remote controller.
• Keep fingers off the touch ring when installing batteries to improve sensitivity. Wait 3 seconds after battery installation before using the remote. Reinstall batteries if the touch ring sensitivity is low.
• This 2.4GHz remote control system is a precision electronic product. Avoid using it in humid, high-temperature, dusty, or high-voltage environments. Store it in a dry, indoor environment free from static electricity.
• Do not use the remote controller in areas with wide-range metal objects or strong electromagnetic waves, as this can significantly affect the control distance.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure without restriction.