Quick Start Guide

In-app Setup

  1. Make sure your Ring Alarm is disarmed.
  2. In the Ring app, tap Set Up a Device and find the Keypad in the Security Devices menu.
  3. Follow the in-app instructions to complete setup.

Installation

  1. Choose a convenient location so you can arm and disarm easily as you come and go.
  2. You can rest the Keypad on a flat surface or install it on a wall with the bracket and screws provided.
  3. The Keypad works whether plugged in or running on the rechargeable battery.

Charge the Keypad using the power adapter and USB cable provided. If you're planning to use the Keypad unplugged, you should fully charge it first.

For additional help, visit: ring.com/help

Placement

The document includes a floor plan suggesting placement for the Ring Keypad within a home. The recommended location is in the main living area, near an entrance, to facilitate easy arming and disarming.

©2020 Ring LLC or its affiliates. Ring, Always Home, and all related logos are trademarks of Ring LLC or its affiliates.

For Z-Wave technical information, visit: ring.com/z-wave

Important Product Information

Safety and Compliance Information

Use Responsibly. Read all instructions and safety information before use.

Safety Information

⚠️ FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE.

  • Ring Keypad is for indoor use only.
  • Do not expose your device or cable to liquids. If your device gets wet, carefully unplug all cables without getting your hands wet and wait for the device and cable to dry completely before plugging them in again. Do not attempt to dry your device or cable with an external heat source, such as a microwave oven or a hair dryer. If the device or cable appear damaged, discontinue use immediately.
  • Use only accessories supplied with the device to power your device.
  • To avoid risk of electric shock, do not touch your device or any wires connected to your device during a lightning storm.

Small Parts Warning

Your device and accessories may present a choking hazard to small children. Keep them out of reach of small children.

General Warnings and Cautions

  • WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.
  • CAUTION: To reduce the risk of electrical shock, DO NOT open the unit. There are no user serviceable parts inside the unit. Refer to customer support for any repairs.
  • CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of the used batteries according to the manufacturer's instructions.

Product Specifications

  • Electrical Rating: 5VDC, 1.0A
  • Temperature Rating: 32°F - 104°F (0°C - 40°C)

Recycling Your Device Properly

In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of, or recycle, your device in accordance with your local laws and regulations. For information about recycling your device, go to www.amazon.com/devicesupport.

Terms of Service and Warranty

Use of the product is subject to your registration with Ring and your agreement with the Terms of Service found at www.ring.com/terms. To review your warranty coverage, please refer to the enclosure inside this box or visit www.ring.com/warranty.

Compliance Information

For Users in the United States

Supplier's Declaration of Conformity - Compliance Information Statement

  • Unique Identifier: Ring Keypad
  • Model: 5AT2S7
  • FCC ID: 2AB2Q5AT2S7

Responsible Party and Party issuing Supplier's Declaration of Conformity: Ring LLC, 1523 26th Street Santa Monica, CA 90404

Website/Contact: www.ring.com/legal, legal@ring.com

FCC Compliance Statement (for products subject to Part 15)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment to a socket on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Pursuant to Section 15.21 of the FCC rules, changes or modifications to a Product by the user that are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

The device meets the FCC Radio Frequency Emission Guidelines. Information on the product is on file with the FCC and can be found by inputting such Product's FCC ID (which can be found on the device) into the FCC ID Search form available at https://www.fcc.gov/oet/ea/fccid.

The party responsible for FCC compliance is Ring LLC, 1523 26th Street Santa Monica, CA 90404.

FCC Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement.

For Users in Canada

Conformité Innovation Sciences et Développement Économique Canada (ISDE)

This device contains license-exempt transmitter(s)/ receiver(s) that comply with Innovation, Science and Economic Development Canada's license-exempt RSS(s). Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

Information Regarding Exposure to Radio Frequency Energy

This equipment complies with IC RSS-102 RF exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

CAN ICES-3 (B)/NMB-3(8)

Z-Wave Device Specific Key (DSK)

Z-Wave DSK: 16713-46346-19515-63606-05946-57005-35337-36926

PDF preview unavailable. Download the PDF instead.

1694AK1SZ Adobe Acrobat Pro DC 20 Paper Capture Plug-in

Related Documents

Preview Ring Keypad 2nd Generation Z-Wave Technical Manual
Comprehensive technical manual for the Ring Alarm Keypad 2nd Generation, covering Z-Wave integration, setup, inclusion, exclusion, factory reset, command classes, configuration parameters, and compliance information.
Preview Ring Mailbox Sensor Quick Start Guide and Safety Information
Get started with your Ring Mailbox Sensor. This guide provides quick setup instructions, safety information, and compliance details for the Ring Mailbox Sensor.
Preview Ring Keypad (5B28S8) Manual and Safety Instructions
This document provides comprehensive setup, installation, safety, and compliance information for the Ring Keypad (Model 5B28S8), including battery handling and product specifications.
Preview Ring Alarm Keypad – 2nd Generation User Manual and Setup Guide
Comprehensive guide for the Ring Alarm Keypad 2nd Generation, covering setup, installation, Z-Wave integration, configuration, and compliance information. Learn how to arm and disarm your system, manage alarm conditions, and utilize Z-Wave features.
Preview Ring Alarm Pro User Guide: Setup, Features, and Security
Comprehensive user guide for the Ring Alarm Pro, covering setup, internet connection, Wi-Fi management, backup options, device integration, alarm modes, professional monitoring, and troubleshooting. Learn how to secure your home with Ring Alarm Pro.
Preview Ring Keypad for Ring Alarm (5B28S8) - Manual & Safety Instructions
Official manual and safety instructions for the Ring Keypad (Model 5B28S8) designed for Ring Alarm systems. Includes setup, installation, wall mounting, safety warnings, battery information, product specifications, and compliance details.
Preview Ring Alarm Pro User Guide: Setup, Features, and Security
Comprehensive user guide for the Ring Alarm Pro smart home security system. Learn how to set up, connect to the internet, customize features, manage security modes, and understand monitoring options.
Preview Ring Base Station Z-Wave Technical Manual
Comprehensive technical manual for the Ring Base Station Z-Wave, detailing procedures for adding and removing sensors, managing Z-Wave network inclusion, lifeline association, and factory reset.