DigiTech HardWire RV-7 Stereo Reverb

Owner's Manual

Brand: DigiTech by HARMAN

Introduction

The DigiTech HardWire series represents significant improvements in guitar effects pedals, offering superior tone and control. Key features include true bypass, high voltage operation, and true stereo processing with genuine Lexicon® reverbs, making them essential for players prioritizing sound quality and performance.

Included Items:

• HardWire RV-7 Stereo Reverb pedal
• StompLock™
• Foot Switch Glow Sticker
• Hook-and-loop Pedalboard Pad
• Online Warranty Registration Information Card

Pedal Interface

The pedal features several controls and connection jacks:

Controls:

• 1. Level Knob: Controls the reverb level.
• 2. DC Adapter Jack: For connecting an optional Harman power supply.
• 3. Liveliness Knob: Controls the amount of high-frequency response in the reverb signal.
• 4. Decay Knob: Controls the length of time the reverb fades out.
• 5. Type Knob: Selects one of 7 Lexicon® reverbs: ROOM, PLATE, REVERSE, MODULATED, GATED, HALL, SPRING.

Jacks:

• 6. Input 1 (Mono): Connect your instrument, a pedal output, or an amp effects send. This jack enables battery power.
• 7. Input 2: Connect a second input for stereo operation.
• 11. Output 1 (Mono): Connect to a single guitar amplifier or amp effects return.
• 12. Output 2: Connect to a second guitar amplifier for stereo use.

Other Features:

• 8. Foot Switch Release Pins: Spring-loaded pins to access the foot switch and battery compartment.
• 9. Indicator LED: Lights when the effect is on. Dims to indicate low battery.
• 10. Foot Switch: Engages and disengages the effect.

Note: Use unbalanced mono instrument cables only.

Tails Switch

The Tails Switch allows the reverb signal to continue after the effect is bypassed (when set to ON). If set to OFF, the reverb signal is cut off immediately upon bypassing.

The switch is located under the foot switch and is accessed by pressing one of the Foot Switch Release Pins with a 1/4" guitar cable plug. Once the foot switch is removed, the Tails Switch is visible inside the chassis. Slide the switch left for Tails ON, and right for Tails OFF.

[Diagram: Shows the Tails Switch with 'ON' and 'OFF' labels, and arrows indicating 'Tails On' (left) and 'Tails Off' (right).]

Setup Configurations

Amplifier Setup

[Diagram: Illustrates connecting the guitar to the RV-7's Input 1, and the RV-7's Output 1 and Output 2 to two separate amplifiers. An optional Harman Power Supply is shown connected to the pedal. An alternative shows a guitar connected to another pedal, then to the RV-7.]

Effects Setup (Effects Loop)

[Diagram: Shows the guitar connected to the RV-7's Input 1. The RV-7's Output 1 is connected to the amplifier's SEND jack, and the amplifier's RETURN jack is connected back to the RV-7's Output 2 (or another output). An optional Harman Power Supply is shown.]

Note: If the amplifier's effects loop includes a mix control, set the mix to 100% full wet.

Battery Operation

If the battery depletes, the HardWire pedals automatically switch to bypass. To replace the battery:

• Push a Foot Switch Release Pin on either side of the foot switch using a 1/4" guitar cable tip to remove the foot switch.
• Remove the old battery from the compartment and disconnect its cable.
• Connect a new battery to the cable and place it in the compartment, ensuring the cable does not interfere with the spring or switch arm.
• Align one hole of the foot switch with its pin, push the opposite pin in, and lower the foot switch into place. Release the pin. Both release pins should be flush with the pedal's outer side when properly fastened.

[Diagram: Shows the internal components of the pedal for battery replacement, labeling the Foot Switch, Pedal Switch Arm, 9VDC Battery, Foot Switch Release Pins, Battery Compartment, Spring, and Pedal Chassis.]

Performance Accessories

The following accessories are included to enhance pedalboard integration:

• Hook-and-loop Pedalboard Pad: Attaches to the pedal's bottom for secure mounting on pedalboards.
• Foot Switch Glow Sticker: Improves visibility of the foot switch on dark stages.
• StompLock™: Secures your knob settings.

Attaching the Hook-and-loop Pedalboard Pad:

1. Peel off the existing rubber skid pad from the bottom of the pedal.

2. Peel the adhesive protector from the back of the Pedalboard Pad.

3. Apply the Pedalboard Pad to the bottom of the pedal.

Attaching the Foot Switch Glow Sticker:

1. Peel the adhesive backing from the Foot Switch Glow Sticker.

2. Apply the Glow Sticker to the top of the Foot Switch.

Using the StompLock:

1. Set the pedal knobs to your preferred setting.

2. Gently push the StompLock over the top of the knobs.

3. To remove, gently lift one side of the StompLock, then the other.

Specifications

Optional Power Supply Compatibility:

Power Supply Polarity: [Diagram: Shows center negative polarity symbol]

Power Supply Output: PS200R (9.6 VDC 300 mA), PS0913DC* (9 VDC 1.3 A)

*Recommended power saving GreenEdge power supply models.

Declaration of Conformity

Manufacturer: Harman Signal Processing, 8760 S. Sandy Parkway, Sandy, Utah 84070, USA

Product Name: RV-7

Product Option: Requires Class II power adapter conforming to EN60065, EN60742, or equivalent.

Conforms to:

• Safety: IEC 60065 -01+Amd 1
• EMC: EN 55022:2006, EN 55024:1998, FCC Part 15

Supplementary Information: Complies with Low Voltage Directive 2006/95/EC, EMC Directive 2004/108/EC, RoHS Directive 2002/95/EC, WEEE Directive 2002/96/EC, and EC Regulation 278/2009.

The product is classified as Professional Audio Equipment and is exempt from Directive 2005/32/EC and EC Regulation 1275/2008. The PS200R power supply, used with this product, is a multi-output supply and is also exempt from these directives.

Declaration Date: October 4, 2010

Signed by: Roger Johnsen, Vice-President of Engineering

European Contact: Local DigiTech Sales and Service Office or Harman Signal Processing, 8760 South Sandy Parkway, Sandy, Utah 84070 USA (Ph: (801) 566-8800, Fax: (801) 568-7583)

Important Safety Instructions

For your protection, please read and follow these instructions:

• Read and keep these instructions.
• Heed all warnings.
• Do not use near water.
• Clean only with a dry cloth.
• Do not block ventilation openings.
• Install according to manufacturer's instructions.
• Do not install near heat sources.
• Protect the power cord from damage.
• Unplug during lightning storms or when unused for long periods.
• No user-serviceable parts inside; refer servicing to qualified personnel.
• WARNING: To reduce the risk of fire or electric shock, do not expose to rain or moisture.
• Refer to unit labels for other markings and information.

Product Disposal

Do not dispose of this product with general household waste. Utilize separate collection systems for used electronic products, adhering to legislation for proper treatment, recovery, and recycling.

Private households in the EU, Switzerland, and Norway may return used electronic products free of charge to designated collection facilities or retailers. For other countries, contact local authorities for disposal methods.

Proper disposal prevents potential negative environmental and health effects.

Warranty Information

DigiTech provides a warranty for its products. Register online at www.digitech.com within ten days of purchase to validate the warranty (valid in the United States).

DigiTech warrants the product to be free from defects in materials and workmanship under normal use and service when purchased new from an authorized U.S. dealer. This warranty is valid for the original purchaser only and is non-transferable.

DigiTech's liability is limited to repairing or replacing defective materials. The warranty period is one year, extended to six years if the product is registered online. A Return Authorization number is required for service.

Proof of purchase is required for warranty service.

DigiTech reserves the right to make design changes without obligation to apply them to previously manufactured products.

The warranty is void if the product is opened or tampered with by unauthorized personnel, or if used with AC voltages outside the suggested range.

This warranty is in lieu of all other warranties, expressed or implied. DigiTech is not liable for consequential damages or delays beyond its control.

Note: Information in this manual is subject to change without notification and may contain inaccuracies due to undocumented product changes.