HARDWIRE SP-7 STEREO PHASER OWNER'S MANUAL

Declaration of Conformity

Manufacturer: Harman Signal Processing

Address: 8760 S. Sandy Parkway, Sandy, Utah 84070, USA

Product: SP-7 Stereo Phaser

Product Option: All (requires Class II power adapter conforming to EN60065, EN60742, or equivalent.)

Conforms to:

• Safety: IEC 60065 -01+Amd 1
• EMC: EN 55022:2006, EN 55024:1998, FCC Part 15

Supplementary Information: Complies with Low Voltage Directive 2006/95/EC, EMC Directive 2004/108/EC, RoHS Directive 2002/95/EC, WEEE Directive 2002/96/EC, and EC Regulation 278/2009.

Regulatory Exemptions: Exempt from Directive 2005/32/EC and EC Regulation 1275/2008 as Professional Audio Equipment. Exempt from Directive 2005/32/EC and EC Regulation 278/2009 for the PS200R power supply as it is multi-output.

Signed by: Roger Johnsen, Vice-President of Engineering, Harman Signal Processing. Date: December 7, 2010

European Contact: Local DigiTech Sales and Service Office or Harman Signal Processing, 8760 South Sandy Parkway, Sandy, Utah 84070 USA. Ph: (801) 566-8800, Fax: (801) 568-7583

Disposal and Environmental Information

Do not mix with general household waste. Use separate collection systems for used electronic products for proper treatment, recovery, and recycling.

Private households in the EU (25 member states), Switzerland, and Norway can return used electronic products free of charge to designated collection facilities or retailers. For other countries, contact local authorities.

This ensures necessary treatment, recovery, and recycling, preventing negative environmental and health effects.

Electromagnetic Compatibility

This device complies with FCC Rules Part 15 and Product Specifications on the Declaration of Conformity, subject to two conditions:

• The device may not cause harmful interference.
• The device must accept any interference received, including interference that may cause undesired operation.

Operation within significant electromagnetic fields should be avoided. Use only shielded interconnecting cables.

Important Safety Instructions

For your protection, read the following:

• Read and keep these instructions.
• Heed all warnings.
• Do not use near water.
• Clean only with a dry cloth.
• Do not block ventilation openings; install according to manufacturer's instructions.
• Do not install near heat sources (radiators, stoves, amplifiers).
• Protect the power cord from being walked on or pinched.
• Unplug during lightning storms or when unused for long periods.
• No user-serviceable parts inside. Refer servicing to qualified personnel. Servicing is required for damage (cord, plug, liquid spill, dropped objects, exposure to rain/moisture, abnormal operation, or drops).
• WARNING: To reduce the risk of fire or electric shock, do not expose to rain or moisture.
• Refer to unit labels for other markings and information.

Warranty

DigiTech is proud of its products and offers the following warranty:

1. Register online at www.digitech.com within ten days of purchase to validate warranty (valid in the United States only).
2. DigiTech warrants the product, when purchased new from an authorized U.S. dealer and used in the U.S., to be free from defects in materials and workmanship under normal use. Warranty is valid to the original purchaser only and is non-transferable.
3. DigiTech liability is limited to repair or replacement of defective materials. Products must be returned to DigiTech WITH RETURN AUTHORIZATION. Parts and labor are covered for one year. This is extended to six years if properly registered online. A Return Authorization number can be obtained by telephone. DigiTech is not liable for consequential damage.
4. Proof-of-purchase (original receipt copy) is the consumer's responsibility for warranty service.
5. DigiTech reserves the right to make design changes or improvements without obligation to apply them to previously manufactured products.
6. Warranty is forfeited if the product's main assembly is opened/tampered with by unauthorized personnel or if used with AC voltages outside the suggested range.
7. This warranty is in lieu of all other warranties, expressed or implied. DigiTech does not authorize anyone to assume liability. DigiTech or its dealers are not liable for special/consequential damages or delays beyond their control.

NOTE: Information is subject to change without notification. Inaccuracies may occur due to undocumented product/system changes. This version supersedes all previous versions.

Congratulations

You have purchased a DigiTech digital effect pedal.

Digital pedals have limited battery life due to constant power draw. For demonstration and practice, battery use is suggested. If the LED brightness changes or the pedal fails to switch between Bypass and Effect, replace the 9-Volt battery or obtain a power adapter from a DigiTech dealer.

Introduction

DigiTech's HardWire series offers significant improvements in guitar effects pedals, providing well-known effects with superior tone and control. Features include true bypass and high voltage operation, making them essential for players prioritizing sound quality and performance.

Included Items:

• HardWire SP-7 Stereo Phaser
• StompLock™
• Foot Switch Glow Sticker
• Hook-and-loop Pedalboard Pad
• Online Warranty Registration Information Card

Setup

Amplifier Setup

Standard Setup: Connect your guitar to the pedal's Input 1 (Mono). Connect the pedal's Output 1 (Mono) to your amplifier's input. An optional Harman Power Supply can be connected to the pedal.

Stereo Setup: Connect your guitar to Input 1 (Mono). Connect Output 1 (Mono) to one amplifier and Output 2 to a second amplifier for true stereo separation.

Effects Loop Setup

Connect your guitar to the pedal's Input 1 (Mono). Connect the pedal's Output 1 (Mono) to your amplifier's effects return (AMP RETURN). Connect your amplifier's effects send (AMP SEND) to the pedal's Input 2.

Note: If your amplifier's effects loop has a mix control, set it to 100% full wet.

Pedal Interface

Diagram shows the top and side views of the HardWire SP-7 Stereo Phaser with controls and jacks labeled:

Controls (Top Panel):

• 1. Speed Knob: Controls LFO speed. Clockwise increases speed, counter-clockwise decreases speed.
• 2. DC Adapter Jack: Connects to the optional Harman power supply. Use the correct voltage for your region.
• 3. Depth Knob: Controls effect intensity. Clockwise for deep sound, counter-clockwise for subtle sound.
• 4. Modify Knob: Controls various settings based on the selected Type. Refer to the Modify Knob Controls table.
• 5. Type Knob: Selects one of the 7 Phaser types.

Jacks and Features (Side/Rear Panel):

• 6. Input 1 (Mono): Primary input. Signals are sent to both outputs when only this input is used. Connecting a guitar cable here also powers the pedal via battery (even if the LED is off). Disconnect cables when not in use to save battery.
• 7. Input 2: Connect for stereo operation. Inputs 1 and 2 are processed and sent to Outputs 1 and 2, maintaining stereo separation.
• 8. Foot Switch Release Pins: Spring-loaded pins that hold the pedal chassis. Push with a 1/4" guitar cable tip to release the pedal chassis and access the battery compartment.
• 9. Indicator LED: Shows if the effect is on or off. Blinks when battery power is low (approx. 15 minutes remaining).
• 10. Foot Switch: Toggles the effect on and off.
• 11. Output 1 (Mono): Connect to a single guitar amplifier input, another pedal input, or an amp effects return.
• 12. Output 2: Connect to a second guitar amplifier for stereo use.

Note: Use unbalanced mono instrument cables only.

Phaser Types

• 2 Stage: Subtle phase effect with adjustable bias control.
• 4 Stage: Classic 4 Stage vintage phaser.
• Modern: Deep phaser with enhanced feedback and modulation.
• Boutique: Unique 6 Stage phaser with deep feedback control.
• 10 Stage: Modern multi-stage phaser with flexible feedback/depth controls.
• Envelope: Triggered phaser where the LFO start point can be retriggered with playing dynamics.
• Dynamic: Phaser where the Depth is controlled using playing dynamics.

Modify Knob Controls

Tap Tempo

The Foot Switch can be used as a Tap Tempo switch to set the phaser's modulation speed during live performance.

To access Tap Tempo:

1. Press and hold the Pedal Switch for 3 seconds. The effect turns on, and the Indicator LED lights solid BLUE. (If the effect was already on, it turns off then back on.)
2. After 3 seconds, the Indicator LED flashes BLUE, indicating Tap Tempo mode is active, flashing at the current modulation speed.
3. Tap the Foot Switch at least twice to set a new modulation speed. The last two tap intervals determine the speed. The function times out after 4 seconds; tap twice again to set the tempo.
4. To exit Tap Tempo, press and hold the Foot Switch for 3 seconds until the Indicator LED stops flashing and lights solid BLUE. The tapped modulation speed remains active until the Type is changed or the Speed knob is used.

Performance Accessories

These accessories help integrate the HardWire pedal into a pedalboard:

• Hook-and-loop Pedalboard Pad: Designed for attachment to most commercial pedalboards.
• Foot Switch Glow Sticker: Enhances visibility on dark stages.
• StompLock™: Secures your knob settings.

Attaching the Hook-and-loop Pedalboard Pad:

1. Peel off the existing rubber skid pad from the bottom of the pedal.
2. Peel the adhesive protector from the back of the Pedalboard Pad.
3. Apply the Pedalboard Pad to the bottom of the pedal.

Attaching the Foot Switch Glow Sticker:

1. Peel the adhesive backing from the Foot Switch Glow Sticker.
2. Apply the Glow Sticker to the top of the Foot Switch.

Using the StompLock:

1. Set the knobs to your preferred setting.
2. Gently push the StompLock over the top of the knobs.
3. To remove, gently lift one side, then the other.

Battery Operation

If battery power depletes, HardWire pedals automatically switch to bypass, eliminating the need to remove the pedal from your chain.

To replace the battery:

1. Using the tip of a 1/4" guitar cable, push one of the Release Pins on either side of the Foot Switch to remove the pedal chassis.
2. Remove the old battery and disconnect its cable.
3. Connect a new battery and place it in the compartment. Ensure the battery cable does not interfere with the spring or pedal switch arm.
4. Place one hole of the Foot Switch over its corresponding pin.
5. Push the opposite pin in and lower the other side of the Foot Switch into place over the depressed pin. Release the pin. Both release pins should be flush with the outer side of the pedal when properly fastened.

Diagram shows: Foot Switch, Pedal Switch Arm, 9VDC Battery, Foot Switch Release Pin, Battery Compartment, Spring, Pedal Chassis.

Specifications

Controls:

Speed, Depth, Modify, Type, On/Off Pedal

Jacks:

Input 1 (Mono), Input 2, Output 1 (Mono), Output 2

Input Impedance:

• Effect on: >1 MΩ (stereo), >500 kΩ (mono)
• Effect off: True hardwire bypass

Output Impedance:

• Effect on: 1 kΩ
• Effect off: True hardwire bypass

Power Supply:

9V Alkaline Dry Battery or Harman power supply

Current Draw:

75 mA (typical at 9 VDC)

Power Consumption:

640 mW (typical w/optional power supply)

Dimensions:

5.25"(L) x 3.5"(W) x 2.15"(H)

Weight:

1.3 lbs.

Optional Power Supply:

Country (Voltage)

Compatible PSU Models

• Japan (100 VAC, 50/60 Hz): PS200R-100 or PS0913DC-01*
• US and Canada (120 VAC, 60 Hz): PS200R-120 or PS0913DC-01*
• Europe (230 VAC, 50 Hz): PS200R-230 or PS0913DC-01*
• UK (240 VAC, 50 Hz): PS200R-240 or PS0913DC-02*
• Australia (240 VAC, 50 Hz): PS200R-240-AU or PS0913DC-02*

Power Supply Polarity: (Center negative)

Power Supply Output: PS200R (9.6 VDC 300 mA), PS0913DC* (9 VDC 1.3 A)

*Recommended power saving GreenEdge power supply models.

Contact Information

Harman Signal Processing

8760 South Sandy Parkway

Sandy, Utah 84070

PH: (801) 566-8800

FAX: (801) 566-7005

DigiTech® and HardWire® are registered trademarks of Harman. Designed in the USA.

Copyright - Harman. Printed in China.

HardWire SP-7 Owner's Manual 5024341-B

Visit our website: www.digitech.com