MPOW 059 LITE Wireless Headphones

Package Contents

• MPOW 059 LITE Wireless Headphones (x1)
• USB Charging Cable (x1)
• 3.5mm Audio Cable (x1)
• User Manual (x1)

Headphone Diagram and Controls

The MPOW 059 LITE headphones feature several controls for easy operation:

• MFB (Multi-Function Button): Central control for various functions.
• Volume Up / Next Track Button (►►►): Increases volume or skips to the next track.
• Volume Down / Previous Track Button (◄◄◄): Decreases volume or goes to the previous track.
• LED Indicator (?): Shows power, pairing, and charging status (red/blue lights).
• Charging Port (?): USB port for charging the headphones.
• Microphone (?): For calls and voice commands.
• Aux Port (?): For wired audio connection.

How to Pair

1. Step 1: Enter Pairing Mode

   With the headphones powered off, press and hold the MFB for approximately 5 seconds until the red and blue lights flash alternately. This indicates the headphones are in pairing mode.

   • Hold on 4s: Power ON (Blue LED)
   • Hold on 5s: Pairing Mode (Red and Blue LEDs alternate)
   • Hold on 5s: Power OFF (Red LED)

2. Step 2: Connect via Bluetooth

   Enable the Bluetooth feature on your cellphone or audio device. Search for "MPOW 059 LITE" in the list of available devices and select it to connect. The connection range is approximately 1 meter (3.3 feet).

Call and Music Control

• Play/Pause/Answer/Hang up/Reject/Redial:
  • Click Once (MFB): Play/Pause music, Answer/Hang up calls.
  • Hold on 1s (MFB): Reject a call.
  • Double Click (MFB): Redial the last number.
  • Siri/Voice Assistant: Double click the MFB to activate.
• Volume Control/Music Control:
  • Click Once (Volume Up/Down): Adjust volume.
  • Hold on 1-2s (Volume Up/Down): Skip to next/previous track.

Charging the Headphones

Connect the provided USB charging cable to the charging port on the headphones and a 5V-1A power source. The LED indicator will show charging status. A full charge takes approximately 2.7 hours.

• Red LED: Charging
• Blue LED: Fully Charged

Clear Paired Device Information

To clear all paired Bluetooth devices from the headphones, refer to the specific instructions in the manual (often involves a combination of button presses while powered on or off).

Frequently Asked Questions (FAQ)

1. Cannot turn on headphones

   • Ensure the headphones are fully charged.
   • If charging, disconnect the USB charging cable before attempting to turn them on.

2. Cannot charge headphones

   • Use the provided USB charging cable.
   • Ensure the USB charging cable is firmly connected to the headphones, USB AC adapters, and computers.
   • Verify that USB AC adapters are firmly connected to power outlets.

3. No sound from the headphones

   • Ensure headphones and paired devices are turned on.
   • Verify that headphones and Bluetooth receiving devices are connected via A2DP Bluetooth profile.
   • Increase the volume if it is too low.
   • Ensure paired devices are operating normally.
   • If connecting to a PC, confirm that the audio output device is set to the Bluetooth® headphones.
   • If using wired mode, ensure the Aux cable is firmly connected.

Regulatory Statements

FCC Statement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

ISEDC RSS Warning

This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference including interference that may cause undesired operation of the device.

This equipment complies with ISEDC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.