Proaim BMP60 R Pro Long Blimp Microphone Windscreen (BMP-60R)
What's In The Box
Please inspect the contents of your shipped package to ensure you have received everything that is listed below.
Illustration showing the components of the Proaim BMP60 R Pro Long Blimp Microphone Windscreen kit: Blimp Extension, XLR Holder, Proaim BMP60 R Pro Long Blimp Microphone Windscreen with Pistol Grip Handle, 60cm Modular Windjammer, Boom Pole Adapter, 40cm Modular Windjammer, 6 x Mic Holders, and Rubbers (40 Pcs).
Features
The Proaim BMP60 R Pro Long Blimp Microphone Windscreen features the following components:
- Blimp Cage: Minimizes wind interference for clear outdoor audio.
- End Cap: Modular end caps keep the microphone safe and firmly in place.
- Blimp Extension: Increases cage length to support long microphones and provides enhanced wind protection.
- Locking Clip: Allows fast and secure setup or removal.
- Ratchet Knob: Enables easy angle adjustment for better handling.
- Pistol Grip Handle: Ensures comfortable handheld use during long shoots.
Diagram illustrating the features of the blimp microphone windscreen with labels pointing to the Blimp Cage, End Cap, Blimp Extension, Locking Clip, Ratchet Knob, and Pistol Grip Handle.
Blimp Mic Windshield Setup
- Hold the blimp cage firmly with one hand. With the other hand, gently twist and pull off the end cap.
- Adjusting the Pistol Grip Handle: Loosen the ratchet knob and then pull down the pistol grip handle.
- Once the handle is in position, tighten the ratchet knob to securely lock it in place.
- Open the locking clip on one side of the blimp cage.
- Repeat the process by opening the locking clip on the opposite side of the blimp cage.
- Slide the mic holder rod out of the blimp cage.
Step-by-step illustrations showing how to remove the end cap, adjust the pistol grip handle by loosening and tightening the ratchet knob, opening locking clips, and sliding out the mic holder rod.
Mic Assembly
NOTE: The mic holder comes with rubber and clamps pre-attached. If any rubber or clamp breaks, you can replace it using the spare parts provided.
- Insert the microphone (Not Included) securely into the mic holder.
- Slide the mic holder rod into the cage until it is firmly seated.
Illustrations demonstrating the insertion of a microphone into the mic holder and sliding the mic holder rod into the blimp cage.
Routing the Mic Cable
- Pass the mic cable through the center of the locking clips.
- Tighten the locking clips securely.
- Attach the end cap to the blimp cage and tighten it securely.
- Route the internal XLR cable through the pistol grip handle for neat cable management.
Step-by-step images showing how to route the microphone cable through locking clips, attach the end cap, and manage the XLR cable through the pistol grip handle.
Attaching to Boom Pole
Note: This ergonomic handle is designed for comfortable handheld operation.
- The handle features a 3/8"-16 threaded base for mounting a boom pole.
- Attach the boom pole (Not Included) to the pistol grip handle.
- Connect the mic's XLR connector to the boom pole's XLR connector.
- The microphone's XLR connector is now properly connected to the boom pole's XLR connector.
Illustrations showing the attachment of a boom pole to the pistol grip handle and the connection of XLR connectors.
Detaching Mic Connectors and Handle
- Disconnect the boom pole's XLR connectors from the mic's XLR connectors.
- Detach the boom pole from the pistol grip handle.
- Pull out the mic cable from the pistol grip handle.
- Loosen the ratchet knob and remove it.
- Take off the handle locking plate from the pistol grip.
- Finally, detach the handle from the blimp cage.
Step-by-step images illustrating the process of detaching the boom pole, mic cable, and handle from the blimp microphone windscreen system.
Boom Pole Adapter Assembly
Feature: This is a shorter attachment with the same 3/8"-16 thread. It's used to mount the blimp cage directly to a boom pole without the long pistol grip. It reduces total length and weight – ideal for extended boom use.
- Insert the screw into the boom pole adapter.
- Attach the spring to the installed screw.
- Insert the screw with spring into the threaded hole of the boom pole adapter.
- Attach the handle locking plate to the opposite side of the boom pole adapter.
- Place the washer onto the boom pole adapter.
- Secure the ratchet knob onto the boom pole adapter and tighten properly.
Features: The boom pole adapter includes two mounting options — 3/8" and 5/8".
- The boom pole adapter comes with a 3/8" mounting.
- To use the 5/8" mounting, remove the grub screw with a screwdriver.
- Once the grub screw is removed, the adapter converts to the 5/8" size.
Illustrations showing the assembly of the boom pole adapter, including inserting screws and springs, attaching plates and washers, and securing the ratchet knob. Also shows the 3/8"-16 thread and how to switch between 3/8" and 5/8" mounting options.
XLR Holder Attachment
- Attach the XLR holder to the boom pole adapter.
- Attach the boom pole to the XLR holder (using the 3/8" mounting).
- Connect the mic's XLR connector to the boom pole's XLR connector.
- Secure the XLR connectors inside the XLR holder.
Step-by-step images demonstrating the attachment of the XLR holder to the boom pole adapter, connecting the boom pole and XLR connectors.
Modular Windjammer Assembly (40cm)
A modular windjammer reduces unwanted noise for clearer audio.
- Begin by unzipping the 40cm modular windjammer.
- Insert the boom pole into the windjammer.
- Zip up the modular windjammer.
Illustrations showing the process of unzipping the 40cm modular windjammer, inserting the boom pole, and zipping it up.
Detaching Modular Windjammer, Mic Connectors and Handle
- Remove the boom pole from the windjammer.
- Zip up the modular windjammer.
- Disconnect the boom pole's XLR connector from the mic's XLR connector.
- Remove the mic cable from the XLR holder.
- Hold the blimp cage firmly with one hand. With the other hand, gently twist and pull off the end cap.
- Remove the mic cable through the center of the locking clips.
Step-by-step images illustrating the detachment of the boom pole from the windjammer, disconnection of XLR connectors, removal of the mic cable, and removal of the end cap.
Assembly Blimp Extension
- Open the locking clip on the opposite side of the blimp cage.
- Slide the mic holder rod out of the blimp cage.
- Remove the mic from the mic holder.
- Insert the mic securely into the mic holder.
- Slide the mic holder rod into the cage until it is firmly seated.
- Open the locking clip on the opposite side of the blimp cage.
Illustrations showing the process of disassembling and reassembling the blimp extension, including opening clips, removing and inserting the mic holder rod, and removing the microphone.
Blimp Extension Attachment
- Hold the blimp extension firmly with one hand. With the other hand, gently twist and pull off the end cap.
- Pull the mic cable out of the blimp extension.
- Attach the blimp extension to the blimp cage.
- Pass the mic cable through the center of the locking clips.
- Attach the end cap to the blimp extension and tighten it securely.
- Connect the mic's XLR connector to the boom pole XLR connector.
- Secure the XLR connectors inside the XLR holder.
Step-by-step images demonstrating the attachment of the blimp extension to the blimp cage, routing the mic cable, and connecting XLR connectors.
Attaching 60cm Windjammer
- Unzip the 60cm modular windjammer.
- Insert the boom pole into the modular windjammer.
- Zip up the modular windjammer.
- Your setup is ready for use.
Illustrations showing the process of attaching the 60cm modular windjammer by unzipping, inserting the boom pole, and zipping it up.
Warranty and Liability
Warranty: Proaim offers a one-year warranty for its products from the date of purchase. Within this period, Proaim will repair the product without charge for labor or parts. The warranty does not cover transportation costs or damage caused by misuse or accidental damage. Warranty repairs are subject to inspection and evaluation by Proaim.
Liability: Proaim is not liable for damage caused by products not supplied by Proaim, or from mishandling in transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than Proaim.
Contact Us: In case of any kind of dissatisfaction, please contact Proaim immediately for support.
