iENYRID iE-ES60 User Manual

Read This Manual Before Using

Why Is It Necessary To Read This Manual Before Operating?

1. This manual was written to help you understand the proper use and maintenance of the iENYRID line of Electric Scooters.
2. It is important to understand the functions and features of the new iENYRID before operating it, as it will allow you to enjoy it from every ride.

Disclaimer & Warning

During the cycling process, comprehensive safety measures should be taken, and risk awareness and good judgment should be maintained at all times to avoid injuries as much as possible.

• The responsibility for iENYRID maintenance is yours! Proper and frequent maintenance will reduce risks of injuries.
• Please wear a helmet, protective gear, and other safety measures when riding.
• Always follow local laws and regulations.
• Do not perform stunts, spins, or jumps; if you insist on doing these dangerous actions, please take full protective measures.

Content

Product & Component Display: Pages 1-2

Product Parameters: Page 3

Products & Accessories: Page 4

Product Installation: Pages 5-6

Product Folding: Page 7

Power On & Unlock & Combination Lock: Page 8

Safe Driving Warning: Page 9

Battery & Charging: Pages 10-11

Error Code: Page 12

After Sales: Page 13

Limited Warranty: Page 14

Warranty Card: Page 15

Product & Component Display

Key Components:

• 01: Instrument
• 02: Brake lever
• 03: Vertical pole
• 04: Folding buckle
• 05: Headlights
• 06: Front fender
• 07: Front shock absorber
• 08: Front motor
• 09: Front wheel
• 10: Folding hook
• 11: Plug
• 12: Side light strip
• 13: Kickstand
• 14: Turn signal
• 15: Rear shock absorber
• 16: Tail lights
• 17: Rear brake
• 18: Rear motor
• 19: Brake pads

Handlebar Components:

• 01: Rear brake lever
• 02: Horn (?)
• 03: Headlight switch (?)
• 04: Power on button (⚡)
• 05: Upshift key (⬆️)
• 06: Downshift key (⬇️)
• 07: Turn signal switch (➡️/⬅️)
• 08: Menu button (☰)
• 09: Gear
• 10: Mileage ( Kmh)
• 11: Left turn signal lamp (⬅️)
• 12: Gear number
• 13: Brake signal/Fault (⚠️)
• 14: Lock the car (?)
• 15: Battery display (?)
• 16: Lamp (?)
• 17: Voltage display (V)
• 18: Cruise control (?)
• 19: Real time speed ( Kmh)
• 20: Single/double motors (⚙️)
• 21: Right turn signal lamp (➡️)
• 22: Fault code display (#️⃣)
• 23: Accelerator (▶️)
• 24: Front brake lever

Product Parameters

Maximum load and speed may vary depending on the rider's weight, riding style and terrain.

Products & Accessories

The iENYRID iE-ES60 package includes:

Product Installation

1. Step 1: Remove the scooter from the packaging box.
2. Step 2: Lift the scooter's folding stem upright.
3. Step 3: Secure the folding latch.
4. Step 4: Ensure that the folding buckle is securely locked, which is a prerequisite for safe driving.
5. Step 5: Adjust the handlebar stem to the correct position.
6. Step 6: Align the screw holes.
7. Step 7: Tighten the handlebar stem screws.
8. Step 8: Ensure all four screws on the handlebar stem are firmly tightened.
9. Step 9: Assembly completed.

Product Folding

1. Step 1: Unscrew the folding latch.
2. Step 2: Pull out the pin.
3. Step 3: Lower the scooter's folding stem.
4. Step 4: Locate the slot corresponding to the latch.
5. Step 5: Secure the latch.
6. Step 6: Folding.

Power On & Unlock & Combination Lock

Powering On: Long press the power button (⚡) to enter the password input interface.

Unlocking: Press the power button (⚡) three times to enter the three-zero password (000), and then quickly press the power button (⚡) twice to unlock it.

The unlocking process takes a short time. It is normal for the screen to turn off if not unlocked within the specified time to protect the scooter from theft. If you forget your password, please refer to the manual.

After unlocking, please wear a helmet and protective gear before cycling, and ensure that all functions of the scooter are normal before starting your ride.

• Unlock the Battery with Original Password: https://www.youtube.com/watch?v=hb6DROovJCw
• Change the Password of Battery: https://www.youtube.com/watch?v=zEp9xpuUlyA

The factory password for the new scooter is: 000.

To change the password, adjust all passwords to 000 and turn them to the left. There is a password change hole at the bottom of the lock. When it is open, use a small stick to press this hole and do not loosen it. Then change the password, release it after completion, and the password change is complete. Just shuffle the password after locking.

Safe Driving Warning

Certain countries or regions require safety devices or gear. It is your responsibility to know the state laws and follow them. However, iENYRID strongly recommends safety gears be donned before operating the device.

TIRE AIR PRESSURE: THE TIRE IS PRESSURIZED TO THE STANDARD VALUE ON THE TIRE.

SAFETY GEAR

Helmet: Most common and serious injuries from riding are head injuries. This can be prevented by donning a helmet. You must wear a helmet when riding the iENYRID Scooter. The helmet must be worn according to its instructions.

MECHANICAL SAFETY

Before using the iENYRID Scooter:

1. Always perform a visual inspection of all screws and nuts to ensure they are tight and in place. If anything is amiss or missing and you are unsure, please contact the seller to confirm safety before use.
2. Check the tires and wheels for signs of wear and tear. Always ensure that the brake mechanism is not touching the wheels and allows free spinning.
3. Always perform mechanical checks of brakes and other parts of the scooter that ensure visibility, safety, and functionality.

Battery & Charging

BATTERY

• Do not charge indoors.
• Do not turn on and operate the scooter while charging.
• Keep the battery away from children, pets, or direct heat.
• Do not expose the battery to high temperature and pressure.
• Please use the charger included with the scooter for charging.
• Please do not throw away batteries to avoid polluting the environment.
• Do not store the scooter for a long period of time with an almost empty battery.
• From time to time, discharge the battery by riding. Recharge the battery again and make sure not to leave the battery fully empty.

Do not charge if the scooter has the following conditions occur:

• The battery leaks.
• The battery is damaged.
• The battery heats up or is deformed.
• The bottom or overall of the deck overheats.

The use, storage, or charging of the battery outside specified limits may result in the annulment of the warranty, battery damage, and ineffective battery charging.

First Charge

It is important to fully charge the battery before your first use of the scooter.

Your scooter's battery comes with these built-in features:

1. Balanced charging protection: During charging, the battery automatically balances the voltage among the internal cells to protect each cell.
2. Over-charging protection: The battery stops charging automatically when full to protect against damage.
3. Over current protection: The battery automatically stops charging if the voltage is higher than the prescribed voltage to protect the battery.
4. Over discharging protection: The battery automatically stops discharging when its voltage drops below the under-voltage value to protect the battery.
5. Short-circuit protection: The battery automatically stops output in the case of a short-circuit.

How to charge

1. Do not charge indoors.
2. Ensure that the scooter is TURNED OFF. Connect the external power charger to the scooter.
3. Connect the charger to an electrical outlet, then turn on the power of the electrical outlet.
4. Do not charge the batteries in temperatures below 5 °C or above 40 °C. The battery may stop the charging process.
5. The charger lights up RED (?) – The battery is charging. The charger lights up GREEN (?) – The battery is fully charged.
6. After the battery is fully charged, please unplug the charger in time.

Error Code

After Sales

Dear customer,

Thank you for choosing iENYRID! To ensure that you can install and use our product smoothly, we strongly recommend that you visit our official website to view the related video installation tutorials and after-sales parts replacement videos.

On our official website, you can find detailed video tutorials that guide you on how to correctly install and use our product. In addition, we also provide after-sales parts replacement videos to ensure that you can correctly perform the replacement when needed.

We hope these videos will help you better understand and use our product. If you still have questions or concerns after watching the videos, please feel free to contact our customer service team, and we will be happy to assist you.

Thank you again for your purchase and support!

Wishing you a pleasant user experience!

iENYRID: https://www.ienyrid.com

Facebook: https://www.facebook.com/iENYRID

YouTube: https://www.youtube.com/@iENYRID

Limited Warranty

BY USING THIS PRODUCT, YOU AGREE TO THIS LIMITED WARRANTY. PLEASE READ THIS LIMITED WARRANTY CAREFULLY.

To benefit from the limited warranty, the customer is advised to read iENYRID Warranty terms together with the "care and maintenance" sections provided in the user manual. This limited warranty applies to the extent permitted by law and unless restricted or prohibited by law.

Attentions for warranty Faults caused by any of the following causes are not within the scope of warranty:

1. Failure to maintain according to this user manual.
2. Product damage or defects caused by improper driver operation.
3. Damage caused by misuse, traffic accident, or accidental collision.
4. Damage caused by riding on abnormal roads or accidental collision.
5. Damage of the vehicle caused by natural disaster or irresistible force.
6. Products which have had their serial numbers removed or tampered with.
7. Defects or malfunctions of the product not notified by the customer during the Warranty Period.
8. Products used for commercial purposes including but not limited to leasing/hiring, use in competitions, etc.
9. Performing high-risk actions such as stunts, spinning, or jumping that lead to rapid aging or malfunction of the product.
10. Exposing this product under blazing sun or outdoors for a long time, as that will speed up the aging process of the product and cause malfunction.
11. Defects or damages from improper storage, exposure to moisture or dampness, modifications, connections, repairs (except as carried out by iENYRID or its authorized centers), misuse, neglect, abuse, accident, alteration, improper installation, or other acts which are not the fault of iENYRID, including damage caused by dropping, blown fuses, liquid entering the interior of the product.

PLEASE ALWAYS KEEP THE BOX FOR ANY POSSIBLE FUTURE AFTER-SALES SHIPMENT.

Warranty Card

Dear user, Thanks for using our electric scooter. Please fill in the form below clearly for the sake of better after-sale services.

Shenzhen Tianshengle Technology Co., Ltd.

• Address: Room 502, 5th Floor, Building 1, Liuwei Business Center, No. 5, Longjing Community, Yangmei Community, Bantian Street, Longgang District, Shenzhen, China
• WhatsApp: +8613612953725
• Customer support: support@ienyrid.com
• Official website: www.ienyrid.com