REMOTE CONTROLLER OWNER'S MANUAL

IMPORTANT NOTE

Thank you for purchasing our air conditioner. Please read this manual carefully before operating your new air conditioning unit. Make sure to save this manual for future reference.

Remote Controller Specifications

NOTE: For models of RG10Y1 (D2)/BGEF, RG10Y2(D2S)/BGEF, if the unit is turned off under COOL, AUTO or DRY mode with the set temperature less than 24°C, the set temperature will be automatically set to 24°C when you turn on the unit again. If the unit is turned off under HEAT mode with the set temperature more than 24°C, the set temperature will be automatically set to 24°C when you turn on the unit again.

Quick Start Guide

1. FIT BATTERIES: Insert batteries into the remote control, ensuring correct polarity. Slide the back cover into place.
2. SELECT MODE: Press the MODE button to cycle through AUTO, COOL [❄️], DRY [?], HEAT [?], and FAN [?] modes.
3. SELECT TEMPERATURE: Use the TEMP ▲ or ▼ buttons to set your desired temperature.
4. SELECT FAN SPEED: Use the FAN SPEED button (or TEMP ▲/▼ for 1% increments) to select the fan speed.
5. POINT REMOTE TOWARD UNIT: Aim the remote control at the air conditioning unit.
6. PRESS POWER BUTTON: Press the ON/OFF button [▶️] to turn the unit on or off.

SPECIAL NOTE

• Button designs on your unit may differ slightly from the example shown.
• If the indoor unit does not have a particular function, pressing that function's button on the remote control will have no effect.
• When there are wide differences between “Remote controller Manual" and "USER'S MANUAL" on function description, the description of “USER'S MANUAL” shall prevail.

Handling the Remote Controller

Inserting and Replacing Batteries

Your air conditioning unit may come with two batteries (some units). Put the batteries in the remote control before use.

1. Slide the back cover from the remote control downward, exposing the battery compartment.
2. Insert the batteries, paying attention to match up the (+) and (-) ends of the batteries with the symbols inside the battery compartment.
3. Slide the battery cover back into place.

BATTERY NOTES

• For optimum product performance: Do not mix old and new batteries, or batteries of different types.
• Do not leave batteries in the remote control if you don't plan on using the device for more than 2 months.

BATTERY DISPOSAL

Do not dispose of batteries as unsorted municipal waste. Refer to local laws for proper disposal of batteries.

TIPS FOR USING REMOTE CONTROL

• The remote control must be used within 8 meters of the unit.
• The unit will beep when remote signal is received.
• Curtains, other materials and direct sunlight can interfere with the infrared signal receiver.
• Remove batteries if the remote will not be used more than 2 months.

NOTES FOR USING REMOTE CONTROL

The device could comply with the local national regulations.

• In Canada, it should comply with CAN ICES-3(B)/NMB-3(B).
• In USA, this device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not approved by the party responsible for compliance could void user's authority to operate the equipment.

Buttons and Functions

Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control. The following is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, refer to the How to Use Basic Functions section of this manual.

ON/OFF

Turns the unit on or off. [▶️]

TEMP ▲

Increases temperature in 1°C (1°F) increments. Max. temperature is 30°C (86°F). NOTE: Press TEMP ▲ and TEMP ▼ buttons simultaneously for 3 seconds to alternate the temperature display between °C and °F.

SET

Scrolls through operation functions: Breeze Away [?️] → Fresh [?] → Sleep [?] → Follow Me [?] → AP mode [?] → Fresh... The selected symbol will flash on the display area; press the OK button [✔️] to confirm.

TEMP ▼

Decreases temperature in 1°C (1°F) increments. Min. temperature is 16°C (60°F).

FAN SPEED

Selects fan speeds in the following order: AU → 20% → 40% → 60% → 80% → 100%. Press the TEMP ▲ or ▼ button to increase/decrease fan speed in 1% increments.

SWING

Starts and stops the horizontal louver movement. Hold down for 2 seconds to initiate vertical louver auto swing feature. [?]

MODE

Scrolls through operation modes: AUTO → COOL [❄️] → DRY [?] → HEAT [?] → FAN [?]. NOTE: HEAT mode is not supported by cooling-only appliances.

ECO/GEAR

Press this button to enter the energy efficient mode sequence: ECO → GEAR(75%) → GEAR(50%) → Previous setting mode → ECO.

OK

Used to confirm the selected functions. [✔️]

TIMER

Set timer to turn unit on or off. [⏰]

BREEZE AWAY

This feature avoids direct airflow blowing on the body and makes you feel indulging in silky coolness. NOTE: This feature is available under COOL, FAN, and DRY modes only.

CLEAN

Used to start/stop the Self Clean or Active Clean function (Model dependent, please refer to the USER'S OPERATION & INSTALLATION MANUAL). [?]

LED

Turns the indoor unit's LED display and air conditioner buzzer on and off (model dependent), creating a comfortable and quiet environment. [?]

Turbo

Enables the unit to reach the preset temperature in the shortest possible time. [?]

Model Information:

RG10A2(D2S)/BGEFU1, RG10Y2(D2S)/BGEF

RG10A10(D2S)/BGEF (20-28°C/68-82°F)

RG10A(D2S)/BGEF & RG10A(D2S)/BGEFU1 (Fresh feature is not available)

RG10A2(D2S)/BGCEFU1 & RG10A2(D2S)/BGCEF (Cooling only models, AUTO mode and HEAT mode are not available)

Remote Screen Indicators

Information is displayed when the remote controller is powered up.

Transmission Indicator

Lights up when the remote sends a signal to the indoor unit. [?]

Display Indicators:

• Breeze Away display (some units) [?️]
• Active clean feature display [?✨]
• Fresh feature display [?]
• Sleep mode display [?]
• Follow me feature display [?]
• Wireless control feature display (some units) [?]
• Low battery detection display (If flashes) [?⬇️]

MODE display

Displays the current mode, including: AUTO, COOL [❄️], DRY [?], HEAT [?], FAN [?].

TIMER ON display

Indicates timer is set to turn ON. [⏰▶️]

TIMER OFF display

Indicates timer is set to turn OFF. [⏰❌]

Silence feature display

Indicates silence mode is active. [?]

ECO display

Displays when ECO feature is activated. [?ECO]

GEAR display

Displays when GEAR feature is activated. [⚙️]

LOCK display

Displays when LOCK feature is activated. [?]

FAN SPEED display

Displays selected fan speed:

• Silence: 1% [*]
• LOW: 2%-20% [*]
• MED: 21%-40% [*]
• HIGH: 41%-60% [*]
• (Higher levels also shown) 61%-80% [*], 81%-100% [*]
• AUTO: AUTO

Note: This fan speed cannot be adjusted in AUTO or DRY mode. Not all models can display fan speed values between AU-100%.

Horizontal louver swing display

Indicates horizontal louver movement. [↔️]

Vertical louver auto swing display

Indicates vertical louver movement. [↕️]

TURBO mode display

Indicates Turbo mode is active. [?]

Not available for this unit [❌]

Temperature/Timer/Fan speed display

Displays the set temperature by default, or fan speed or timer setting when using TIMER ON/OFF functions.

• Temperature range: 16-30°C/60-86°F / (20-28°C/68-82°F) (Model dependent)
• Timer setting range: 0-24 hours
• Fan speed setting range: AU -100%

This display is blank when operating in FAN mode.

Note: All indicators shown in the figure are for clear presentation. During actual operation, only relative function signs are shown on the display window.

How to Use Basic Functions

ATTENTION: Before operation, please ensure the unit is plugged in and power is available.

AUTO Mode

1. Select AUTO mode using the MODE button.
2. Set your desired temperature using the TEMP ▲/▼ buttons.
3. Turn on the air conditioner using the ON/OFF button.

NOTE: 1. In AUTO mode, the unit automatically selects COOL, FAN, or HEAT based on the set temperature. 2. Fan speed cannot be set in AUTO mode.

COOL or HEAT Mode

1. Select COOL or HEAT mode using the MODE button.
2. Set the temperature using the TEMP ▲/▼ buttons.
3. Set the fan speed using the FAN SPEED button.
4. Turn on the air conditioner using the ON/OFF button.

DRY Mode

1. Select DRY mode using the MODE button.
2. Set your desired temperature using the TEMP ▲/▼ buttons.
3. Turn on the air conditioner using the ON/OFF button.

NOTE: In DRY mode, fan speed cannot be set as it is automatically controlled.

FAN Mode

1. Select FAN mode using the MODE button.
2. Set the fan speed using the FAN SPEED button.
3. Turn on the air conditioner using the ON/OFF button.

NOTE: In FAN mode, you cannot set the temperature. As a result, no temperature displays on the remote screen.

Setting the TIMER

TIMER ON/OFF - Set the amount of time after which the unit will automatically turn on/off.

TIMER ON setting

1. Press the TIMER button to initiate the ON time sequence.
2. Press the TEMP ▲ or ▼ button multiple times to set the desired time to turn on the unit.
3. Point the remote toward the unit and wait 1 second; the TIMER ON will be activated.

TIMER OFF setting

1. Press the TIMER button to initiate the OFF time sequence.
2. Press the TEMP ▲ or ▼ button multiple times to set the desired time to turn off the unit.
3. Point the remote toward the unit and wait 1 second; the TIMER OFF will be activated.

NOTE: 1. When setting TIMER ON or TIMER OFF, the time increases by 30-minute increments up to 10 hours. After 10 hours, it increases in 1-hour increments up to 24 hours. (e.g., 5 presses = 2.5h, 10 presses = 5h). The timer reverts to 0.0 after 24 hours. 2. Cancel either function by setting its timer to 0.0h.

TIMER ON & OFF setting (example)

Keep in mind that the time periods you set for both functions refer to hours after the current time.

Example: If the current time is 1:00 PM, to set the timer as described, the unit will turn on 2.5 hours later (3:30 PM) and turn off at 6:00 PM.

How to Use Advanced Functions

Swing function

Press the Swing button [?]. The horizontal louver will swing up and down automatically. Press again to stop.

Keep pressing the Swing button for more than 2 seconds to activate the vertical louver swing function (Model dependent).

If you continue to press the SWING button, five different airflow directions can be set. The louver moves to a certain range each time you press the button. Press until your preferred direction is reached.

NOTE: When the unit is off, press and hold MODE and SWING buttons together for one second to open the louver for cleaning. Press and hold MODE and SWING buttons together for one second to reset the louver (Model dependent).

LED DISPLAY

Press the LED button [?] to turn the indoor unit's display and buzzer on and off.

Press this button for more than 5 seconds (some units) to display the actual room temperature. Press again for more than 5 seconds to revert to displaying the set temperature.

ECO/GEAR function

Press this button to enter the energy efficient mode sequence: ECO → GEAR(75%) → GEAR(50%) → Previous setting mode → ECO...

Note: This function is only available under COOL mode.

ECO operation:

Under cooling mode, pressing this button adjusts the temperature automatically to 24°C/75°F and fan speed to Auto for energy saving (only when the set temperature is less than 24°C/75°F). If the set temperature is above 24°C/75°F, the fan speed changes to Auto, and the set temperature remains unchanged.

NOTE: Pressing the ECO/GEAR button, or modifying the mode or adjusting the set temperature to less than 24°C/75°F will stop ECO operation. Under ECO operation, the set temperature should be 24°C/75°F or above; otherwise, it may result in insufficient cooling. If you feel uncomfortable, press the ECO button again to stop it.

GEAR operation:

Press the ECO/GEAR button to enter GEAR operation as follows:

• 75% (up to 75% electrical energy consumption)
• 50% (up to 50% electrical energy consumption)
• Previous setting mode.

Under GEAR operation, the display on the remote controller will alternate between electrical energy consumption and set temperature.

SHORTCUT function

Press the SHORTCUT button (some units). Push this button when the remote controller is on; the system will automatically revert to the previous settings, including operating mode, setting temperature, fan speed level, and sleep feature (if activated).

If pushed for more than 2 seconds, the system will automatically restore the current operation settings, including operating mode, setting temperature, fan speed level, and sleep feature (if activated).

Silence function

Keep pressing the FAN button for more than 2 seconds to activate/disable Silence function (some units). [?]

Due to low frequency operation of the compressor, it may result in insufficient cooling and heating capacity. Pressing ON/OFF, Mode, Sleep, Turbo, or Clean button while operating will cancel silence function.

FP function

The unit will operate at high fan speed (while compressor is on) with the temperature automatically set to 8°C/46°F.

Note: This function is for heat pump air conditioners only.

Press this button 2 times within one second under HEAT Mode and setting temperature of 16°C/60°F or 20°C/68°F (for models of RG10A10(D2S)/BGEF, RG10B10(D2)/BGEF and RG10B10(D2)/BGCEF) to activate FP function.

Pressing ON/OFF, Sleep, Mode, Fan, and Temp. buttons while operating will cancel this function.

LOCK function

Press the Clean [?] and Turbo [?] buttons together for more than 5 seconds to activate Lock function. All buttons will not respond except pressing these two buttons for two seconds again to disable locking. [?]

SET function

Press the SET button to enter the function setting, then press the SET button or TEMP ▲/▼ button to select the desired function. The selected symbol will flash on the display area; press the OK button [✔️] to confirm.

To cancel a selected function, perform the same procedures as above.

Press the SET button to scroll through operation functions:

• Breeze Away [?️]
• Fresh [?]
• Sleep [?]
• Follow Me [?]
• AP mode [?]

[*]: If your remote controller has dedicated Breeze Away, Fresh, or Sleep buttons, you cannot use the SET button to select these features.

Breeze Away function [?️] (some units):

This feature avoids direct airflow blowing on the body and makes you feel indulging in silky coolness. NOTE: This feature is available under COOL, FAN, and DRY modes only.

FRESH function [?] (some units):

When the FRESH function is initiated, the ion generator is energized and helps purify the air in the room.

Sleep function [?]:

The SLEEP function is used to decrease energy use while you sleep (and don't need the same temperature settings to stay comfortable). This function can only be activated via remote control. For details, see "sleep operation" in the "USER'S MANUAL". Note: The SLEEP function is not available in FAN or DRY mode.

Follow me function [?]:

The FOLLOW ME function enables the remote control to measure the temperature at its current location and send this signal to the air conditioner every 3-minute interval. When using AUTO, COOL, or HEAT modes, measuring ambient temperature from the remote control (instead of from the indoor unit itself) optimizes the temperature around you for maximum comfort.

NOTE: Press and hold the Turbo button for seven seconds to start/stop the memory feature of Follow Me function.

• If the memory feature is activated, "On" displays for 3 seconds on the screen.
• If the memory feature is stopped, "OF" displays for 3 seconds on the screen.
• While the memory feature is activated, pressing ON/OFF, changing the mode, or power failure will not cancel the Follow me function.

AP function [?] (some units):

Choose AP mode for wireless network configuration. For some units, this does not work by pressing the SET button. To enter AP mode, continuously press the LED button seven times in 10 seconds.

Disclaimer

The design and specifications are subject to change without prior notice for product improvement. Consult with the sales agency or manufacturer for details.

CR2756-RG10(D2S)

16117000A37345

2021.05.08