MCombo Lift Recliner Owner's Manual

Welcome and Introduction

Hello, Thank you for choosing MCombo® Let's get started

Purchaser's Agreement

By accepting delivery of this product, you promise that you will not change, alter, or modify this product or remove or render inoperable or unsafe any guards, shields or other safety features of this product. You will not refuse or neglect any retrofit kits that MCombo may provide to enhance and preserve the safe use of this product.

I. SAFETY GUIDELINES

1. Mandatory

Read the safety and other instructions thoroughly before using your MCombo® product. Failure to follow the guidelines, warnings in this manual and those located on your product can result in personal injury or product damage and will void the product warranty. Keep this manual for future reference.

2. Danger

• To prevent suffocation, keep plastic bags away from children.
• Do not allow children play on or near the chair when in use. Serious injury or death could occur if a child is under the chair when the chair is in motion.
• Keep cord out of reach of small children, and do not use where it may be a trip hazard.
• Plug directly into a wall outlet. Do not use an extension cord or adapter.
• Avoid exposing upholstered chair to burning cigarettes or cigars, open flames, and high temperatures.
• Do not use this product if it is wet, in water, around water or any liquid.
• Always leave in an upright and closed position. Keep hands and feet clear of mechanism and all moving parts. Footrest must be completely closed before getting in or out of the chair. Only the occupant should operate the chair.
• Before moving the product, disconnect the electrical plug from the wall outlet and secure the mechanism to prevent unexpected lifting and movement of the chair.
• Do not attempt to disassemble or repair the actuator or pump; no serviceable parts are inside.
• Do not allow electrical cord to be pinched between moving parts or between the frame and the floor. Do not place cord under carpet or in a location where it could become worn.
• Do not use pillow, blanket, or other cover between occupant and chair surface when heat is engaged.
• Do not attempt to disconnect the power plug by pulling the power cord. Always hold the power plug and pull it out.
• Closely supervise children and disabled persons using this product.
• To reduce the risk of head entrapment and other injuries, keep children and pets away from openings and moving parts in and around furniture.
• Unplug power cords from outlet before relocating or troubleshooting.
• This product has many moving parts, serious injury can occur if not used properly. Keep hands, fingers, and body parts away from the mechanism.
• To exit the unit safely and prevent a tripping hazard, bring the back upright and close the footrest.
• Place tables and area rugs at a distance to allow the footrest to fully extend without rubbing or interference.
• Check the condition of the power supplies, electrical cords, plugs, and connectors often. Keep the power supplies and electrical cords away from heat sources. Never operate the unit with a damaged power supply, electrical cord, plug or connector.
• This product is not intended for use as a health care device. Some medications and physical limitations may impair your ability to operate this product in a safe manner. Consult your physician if you are taking prescribed or over the counter medication, or if you have physical limitations.
• Do not charge your device into the USB charge ports over 24 hours.
• Do not charge any devices over 5V/2A with the USB charge ports.
• Do not overlay the USB charge ports with other heat-dissipating electronic products. This may prevent heat dissipation and cause overheating or melting.
• Users of medical devices should contact their health care provider before using this product.
• Unplug the power cord immediately if you detect strange odors or fumes coming from the chair. Contact your MCombo Customer Support.
• Burns may result from improper use and care of internal heating parts. To avoid risk of burns, do not use pins, do not allow heating pad area to become wet, and do not remove upholstery cover.
• The chair is intended for a single occupant, not exceeding 350 lbs. Do not operate the chair with more than one occupant in or on any part of the chair.
• If you give this product to someone else, must include this owner's manual.

3. Warning

• Weight Capacity: 350 lbs.
• Do not use outdoors. INDOOR USE ONLY.
• To avoid tip over, do not put your weight against the back of the chair.
• Do not stand, sit, or place extra weight on the arms, back or open footrest.
• Do not use this product if it is damaged. Do not use attachments or substitute parts.
• Do not use this product if you have poor circulation, are mobility-impaired, or cannot sense heat, except as directed by your health care provider.
• Do not operate the unit until the back is installed and locked.

4. Symbols Information

The symbols below represent labels used on the product to identify warnings, mandatory actions, and prohibited actions. It is especially important for you to read and understand these symbols completely. Do not remove these labels from your product. Please note that not all the symbols may be used on your chair.

• ? [Read Manual]: Read and follow the information in the owner's manual
• ⚖️ 350 lbs: Weight Capacity: 350 lbs
• ?❌ [No Extension Cord]: Do not connect an extension cord to the AC/DC converter
• ? [No Objects Under Footrest]: Do not place objects under the footrest when lift chair is in fully reclined position
• ? [Pinch Hazard]: Pinch/Crush Points Hazard
• ⚡ [Electrical Hazard]: Electrical Hazard
• ⛑️ [Class II Equipment]: Class II Equipment
• ? [Indoor Use Only]: Indoor Use Only

5. Disclaimer

Make sure you read and understand this manual completely before using your Mcombo Product. We are not and cannot be held responsible for any damage or injury incurred due to improper or unsafe use of the Mcombo Product. We specifically disclaim responsibility for any bodily injury or property damage that may occur during any use that does not comply with applicable federal, state, or local laws or ordinances.

II. ASSEMBLY INSTRUCTIONS

1. Product Parameters

2. Part List

Notice: The chair is delivered in MULTIPLE boxes. Please check if you have received all parts of the chair. Use Mcombo parts only for all replacements.

• A Base x 1
• B Backrest x 1
• C1 Right Armrest with USB × 1
• C2 Left Armrest x 1
• D Lift Remote x 1 (6160-FF-HLR)
• E Massage Remote x 1 (6160-BB-BM)
• F Power Adapter x 1 (6160-FF-29V-Angle)
• G Anti-back-tipping x 2 (6160-AA-BW)
• H Rack circular gasket x 2 (Spare parts)

3. Assembly Steps

Step1 - Anti-back-tipping Part Assembly

1. Place the Anti-back-tipping parts (G) near the bottom of base. 2. Align the screws with the holes then tighten the wing screws.

Step2 - Armrest Assembly

1. Ensure the armrest which has USB charge port is located on right of base. 2. Slide the left and right armrest into the brackets of the base. 3. Press each armrest down as far as it will go. NOTE: Ensure the two connections on each armrest are both inserted into the seat tightly.

Step3 - Backrest Assembly

1. Align the brackets of backrest at the clips of seat-back. 2. Push the brackets into the seat-back tightly. Listen for a "click" sound on each side to ensure the backrest is locked in properly. ATTENTION: Remove the plastic cap before assembling backrest.

Step4 - Lift Connections

1. Before attaching the lift remote and massage remote to the base, please get wires through the side loops of either side armrest according to the user's preference. 2. Connect the chairs according to the following wiring diagram. 3. Attach the chair-back to the velcro on the bottom of the chair base.

Step5 - Final Check

1. Make sure both metal brackets on each armrest are mounted on the base. 2. Make sure the backrest inserts are locked to the base. 3. Make sure all wires are connected tightly. 4. Make sure all wires are not placed on the bottom of the rack and will not be pressed by frame. 5. Make sure the anti-tilt fitting screws are tightened.

III. OPERATING INSTRUCTIONS

1. Operation Precautions

• Do not use an extension cord.
• Do not exceed recommended weight limit.
• Do not use attachments not recommended by the manufacturer.
• Do not use outdoors. INDOOR USE ONLY.
• Use this lift only for its intended use as described in the operating.
• Keep dry. Do not operate in a wet or moist environment.
• Keep all cords away from heated surfaces and pinch points.
• Ensure the hand control is out of the way before sitting in the chair.
• Always leave the lift chair in an upright and closed position when not in use.
• Periodically check the hand control and all power cords for visible damage.
• Do not use the footrest as a seat, or for purposes outside its intended use.
• Do not lean or apply downward force to the chair-back while in recline position.

2. Lift Operation Instruction

Remote Buttons:

• Press to recline the backrest of the chair.
• Press to raise the backrest of the chair.
• HOME: Press to return the chair to Normal position from any position. (The lift motor of the backrest will run for 5 seconds first, and then the lift motor of the base will run, to improve safety and sense of use during use.)
• Press to raise the seat and return the extension footrest.
• Press to recline the base and lift extension footrest brace.

NOTE: If you discover a problem at any point during the setup and positioning of your lift chair, stop and contact the Mcombo Customer Support immediately. To avoid personal injury and/or product damage, do not plug the unit into the electrical outlet until the problem is corrected and do not attempt to fix electrical problems by yourself.

NOTE: You need to calibrate the control box: 1. If you press the HOME button and the chair does not return to its upright position. 2. If the lift and recliner functions do not work as the lift remote request. To calibrate the control box, keep pressing any one of the two buttons that control the footrest until you hear a "beep" sound which signifies that the control box has been calibrated.

3. Massage Remote Operation Instruction

NOTE: Use the heating only: Turn off the POWER button, turn on the HEAT button. (Heating function works with vibration separately.)

IV. CARE AND MAINTENANCE

Your Mcombo product will provide years of superior performance and satisfaction with regular care and maintenance. To maintain the finish quality of your "assistant", please follow the guidelines and cleaning procedures provided below.

Notice

• Do not place your chair in direct sunlight, as sunlight causes fading.
• Do not smoke cigarettes while sitting in or using your chair.
• Avoid extreme changes in temperature by arranging chair away from radiators, heat and air vents.
• Do not use solvent-type cleaners to spot clean.
• Do not saturate fabric.
• Please be careful that pet scratch may cause fabric or leather break.

1. Fabric Care

• Inspect the fabric on a regular basis for any pulls, tears, or gaps.
• Frequent vacuuming or light brushing with a nonmetallic, stiff bristle brush to remove dust and grime is recommended.
• When liquid spills onto the fabric, please immediately wipe off liquid spills with a dry or lightly dampened clean white cloth, sponge, or paper towel.

2. Faux Leather Care

• Wipe leather down regularly with a clean, dry microfiber cloth.
• For more stubborn dust, dampen the cloth with distilled water. Make sure that the cloth is not soaking wet. Never let water soak into leather.
• Always be sure to use a soft cloth and never use an abrasive brush or scrubber as this can scratch and damage the leather.

3. Electronics Care

• Inspect all wiring harnesses to make sure they are not damaged or stuck under chair.
• Keep all the electronics free from moisture and temperature extremes.
• Check electrical components frequently for signs of corrosion and replace as necessary.
• Contact Mcombo Customer Support if damage is present, do not fix it by yourself.

4. Disposal & Recycling

Your power recliner sofa must be disposed of according to applicable local and national statutory disposal regulations. Contact your local waste disposal agency for information on proper disposal of recliner sofa packaging, metal/wood frame components, fabric, electronic components.

V. TROUBLESHOOTING

NOTE: If the lift recliner still does not operate properly, please contact the Mcombo® Customer Support for help and never attempt to make any repairs or adjustments yourself.

Lift Motor Replacement

Step1 - Turn the Chair to the Left

First turn the chair to the left, the right armrest is upward, be careful not to break the wire of USB charge ports.

Step2 - Unplug the Wire of Lift Motor

The diagram shows wires being disconnected from the lift motor. It illustrates specific connectors labeled 1 through 5 being unplugged.

Step3 - Remove Bolts

The diagram shows a bolt being removed. It details steps: (1) The original position of the paper clip, (2) Twist the paper clip, (3) Pull out the paper clip, (4) Pull out the bolt. The disassembled small parts need to be put away to prevent falling into the rack.

Step4 - Replace the New Lift Motor

Insert bolts and paper clips at both ends of the lift motor. The diagram shows the new motor being installed. NOTE: Please note that the motor of the lift motor is upward, be careful not to install it backwards, otherwise the lift motor will break.

Step5 - Plug in the Wire of Lift Motor

The diagram shows the wires being reconnected to the new lift motor, illustrating connectors 1, 2, 3, 4, and 5 being plugged in. NOTE: Please make sure all wires are not been crushed or pulled.

Step6 - Final Check

Check & Confirm

1. Make sure bolts and paper clips are fully inserted. 2. Make sure the lift motor is installed in the correct direction. 3. Make sure the wires are not crushed by the seat frame.

VI. DISASSEMBLY INSTRUCTION

Notice

• Ensure the chair is in seated position and its footrest return to original position.
• Please unplug the power cord before disassembling.
• Please refer to the installation steps from back to front and disassemble the chair in reverse order.

Step1 - Disconnect all Connections

Please disconnect all connections on the chair base and backrest before disassembling.

Step2 - Disassemble Backrest

1. Pushing the metal ears of the backrest inserts outward. 2. After unlocking the metal lugs on both sides of the backrest, hold the bottom part of the backrest marked in the picture below and pull it vertically upward. ATTENTION: After unlocking the metal tabs on both sides of backrest, pull the backrest upward.

Step3 - Disassemble Armrests

NOTE: Need to remove the backrest first. It is best to remove armrest by two people. When lifting the armrest, be sure to hold the bottom of the armrest to avoid damaging the armrest bag and cup holder. 1. Use your knees to find a support point on the seat and press on the base with your own strength. 2. Hold the two marked positions at the bottom of the armrest and lift the armrest vertically upward. Shake the armrest slightly to loosen the brackets, make it easier to detach from the base.

VII. WARRANTY

Notice

• For product beyond the limited manufacturer warranty period and scope, Mcombo® can also provide replacement service, but a basic charge will be charged according to the circumstances.
• The warranty only applies to Mcombo® products and does not include any accessories or enhancements.
• Warranties are only valid in the 48 contiguous United States and are contingent upon the consumer operating the product according to the corresponding instruction manual.

Warranty Periods

CONSUMER WARRANTY LIMITATIONS AND EXCLUSIONS

All warranties begin on the date of delivery. All warranties are to the original purchaser from MCOMBO® ONLY. MCOMBO® will replace the defective parts or send replacement product provided that the warranty parts have not been subjected to misuse, abuse or improper service by the consumer, for example, damaged wire arising in consequence of negligence or improper operation. Exclusions also include components with damage caused by: Contamination, Abuse, misuse, accident, or negligence, Commercial use, or use other than normal, Improper operation, maintenance, or storage.

NOTE: Mcombo will pay standard shipping rates on all warranted parts for two years. We can also sell you replacement part for a discount price when your product is out of warranty policy.

VIII. RETURN/ REPLACEMENT POLICY

Notice

Why don't we recommend returning the item by yourself?

• Huge cost - UPS/FedEx oversize fee.
• Need you to take the box to UPS/FedEx facility.

Return/ Replacement Policy

MCOMBO® You have 30 days from the date of purchase to return any item purchased from our store. Please securely pack the item in its original packaging, including any accessories or manuals that came with the product. To initiate a return, please contact our customer service team at sales@mcombo.com/ 323-597-1109 for any help.

Return Conditions

We accept the return of items that are in new, unused condition, with original tags attached and all original packaging and other components included. Refunds will be issued in the original form of payment for the price of the item, including taxes.

NOTE: Please keep the original packaging in case the product needs to be returned. If the original packaging is not available, the newly found packaging needs to meet the following size standard: UPS/FedEx packaging size standard: (width+ height) * 2+ length< 128 inch. Please disassemble the product before you return it, otherwise there will be a huge cost as oversized and it could even exceed your order amount. Please do not purchase return label for a damaged/defective product by yourself. If you have any problem to return the product, please contact us immediately, we will do our best to help you with a reasonable solution.

IX. MCOMBO CUSTOMER SUPPORT

Contact Mcombo Customer Support for assistance.