Caséta Wireless Quick-Start Guide

Installing Your Dimmer

Installation for lights with one wall switch (single pole)

1. Turn power off at circuit breaker!

   WARNING: SHOCK HAZARD. May result in serious injury or death. Turn off power at circuit breaker or fuse before installing.

2. Remove existing switch from wall

   Remove the wallplate from the switch. Then, remove the switch and pull it away from the wall.

   [Diagram: Shows removing wallplate and then switch from wall.]

3. Remove side sections (if necessary)

   Some dimmers may require side sections to be removed. Bend back and forth to remove. Do not remove outside side sections on dimmers at the end of a gang. Each dimmer has inside side sections removed. A dimmer in the middle of a gang has all side sections removed.

   [Diagram: Illustrates removing side sections from the dimmer, showing different configurations for single vs. multi-gang installations.]

4. Disconnect all three wires* from the switch.

   [Diagram: Shows wires disconnected from the old switch.]

5. Connect the dimmer
   1. Connect the bare copper (or green) "ground" wire from the wallbox to the green wire on the dimmer using a wire connector.
   2. Connect either of the remaining wires from the wallbox to either of the remaining wires on the dimmer using a second wire connector.
   3. Connect the remaining wire from the wallbox to the remaining wire on the dimmer using a third wire connector.

   [Diagram: Shows the dimmer's wires being connected to the wallbox wires using wire connectors. Labels indicate ground-to-ground connection first.]

6. Mount the dimmer

   Use the provided screws to secure the dimmer to the wallbox.

   [Diagram: Shows dimmer being screwed into the wallbox.]

7. Attach the wallplate

   Attach the adapter to the dimmer using the screws provided and snap on the wallplate. If you installed the dimmer next to other dimmers or switches, you'll need a wallplate with the correct size/number of openings.

   [Diagram: Shows adapter attached to dimmer, then wallplate snapping into place.]

8. Turn power on at circuit breaker

Contents Supplied

• In-wall dimmer (PD-6WCL)
• Wire connectors (3)
• Screws (2)

Tools You'll Need

• Flat-head screwdriver
• Phillips-head screwdriver
• Pliers

Important Notes

Some lights have one wall switch, while others have two or more wall switches (such as stair lights). These instructions are for lights with one wall switch (single pole). If your light has more than one switch (a 3-way application), please visit www.casetawireless.com/3way for complete installation instructions and videos.

Maximum Wattage Derating Chart

Removing side sections reduces the dimmer's maximum wattage rating. See the chart below for maximum wattage information.

*For maximum wattage information when mixing light bulb types, see www.casetawireless.com/ganging.

*If your switch has more than 3 wires attached, see the "Installing Caséta Wireless in a 3-way switch application" video at www.casetawireless.com/3way.

Cautions and Codes

CAUTION: Use only with permanently installed fixtures with dimmable LED, dimmable CFL, halogen, or incandescent lamps. To avoid overheating and possible damage to other equipment, do not use to control receptacles, motor-driven appliances, or transformer-supplied appliances.

Codes: Install in accordance with all national and local electrical codes.

Grounding: When no "grounding means" exist in the wallbox, the National Electrical Code (NEC®) allows a control to be installed as a replacement if 1) a nonmetallic, noncombustible faceplate is used with nonmetallic attachment screws or 2) the circuit is protected by a ground fault circuit interrupter (GFCI). When installing a control according to these methods, cap or remove the green wire before screwing the control into the wallbox.

FCC/IC Information: This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. Modifications not expressly approved by Lutron Electronics Co., Inc. could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.

Works with Energy Efficient Dimmable Light Bulbs

• LED: up to 150 W
• CFL: up to 150 W
• Halogen: up to 600 W
• Incandescent: up to 600 W

Note: You can mix and match dimmable LED and CFLs, as well as halogen and incandescent light bulbs, with Caséta™ Wireless dimmers. Dimmable LED and CFL light bulbs vary in their dimming performance. If you're using these bulbs and they flicker or turn off, please visit www.casetawireless.com/lowend for information on adjusting the dimmer for best bulb performance.

For a complete list of compatible dimmable LEDs and CFLs, please visit www.casetawireless.com/bulblist.

Compatible light bulbs include:

• Cree® BA19-080270MF-12DE26-1U100, CR6-575L
• EcoSmart® ECS BR30 W27 FL 120, ECS 20 WW FL 50WE 120
• Feit® A19/OM/LED
• Philips® 9290002295
• Sylvania® LED12A19/DIM/0/827, LED21PAR38/DIM/P/930/FL30

Using Your Caséta™ Wireless Kit (Sold Separately)

With a Smartphone or Tablet (Bridge Required, Sold Separately)

The Caséta™ Wireless dimmer can be controlled from a smartphone when used with the Lutron Smart Bridge™. If you are using the dimmer and remote control with the Lutron Smart Bridge™, follow the instructions below. Note: If you are using the dimmer and remote control with another manufacturer's bridge, please refer to that manufacturer's instructions for set-up.

1. Download the Lutron® app

   Search for "Lutron Caseta" on the Google Play Store or Apple App Store. Visit www.casetawireless.com/LutronApp.

   [Icons for Google Play and App Store]

2. Launch the Lutron® app

   The Lutron® app will walk you through setting up your devices.

3. Use the Lutron® app to complete ALL remaining steps

   Add devices (Pico® remotes, Dimmers, Shades), Control your lights three ways, Schedule your lights, Connect while away.

   [Diagram: Shows app interface elements for adding devices, scheduling, etc.]

Without a Smartphone or Tablet (Bridge Not Required)

Pairing the Dimmer and Pico® Remote Control

1. Press and hold the "off" button on the dimmer for 6 seconds until LEDs start blinking.
2. Press and hold the "off" button on the Pico® remote control for 6 seconds until the lights flash 3 times.
3. Repeat steps to pair other Pico® remote controls.

[Diagram: Shows button presses on dimmer and remote for pairing.]

Changing the Favorite Light Level on the Pico® Remote Control (Sold Separately)

You can use the round "favorite" button on the Pico® remote control to recall a favorite light level. We've set it to 50%, but you can change it to any level you like.

1. Set the desired light level on the dimmer.
2. Press and hold the "favorite" button on the Pico® remote control for 6 seconds until the LEDs blink twice on the in-wall dimmer. The new favorite level is now saved.

[Diagram: Shows setting light level on dimmer and pressing favorite button on Pico remote.]

Using Your Controls

In-wall Dimmer

Controls:

• On/Off: Press the top of the large button.
• Brighter: Press and hold the raised icon on the top of the large button.
• Darker: Press and hold the icon on the bottom of the large button.
• Off: Press the bottom of the large button.
• FASTM (Front Accessible Service Switch): Located on the bottom edge. Pull out to remove power at the light socket for bulb replacement.

[Diagram: Shows the in-wall dimmer with labels for On/Off, Brighter, Darker, and FASTM switch.]

Replacing Light Bulbs Using FASTM

Pull the FASTM switch out on the in-wall dimmer to remove power at the light socket.

Pico® Remote Control

Controls:

• On: Press the top button.
• Favorite: Press the round button to recall the saved favorite light level.
• Darker: Press and hold the bottom button.
• Off: Press the bottom button.

[Diagram: Shows the Pico remote control with labels for On, Favorite, Darker, and Off buttons.]

Important Notes

• For indoor use only.
• Operate between 32 °F (0 °C) and 104 °F (40 °C).

Troubleshooting

Go to www.casetawireless.com/support for additional troubleshooting suggestions.

Device Ratings

In-wall dimmer: PD-6WCL, 120 V~ 50/60 Hz