Step 1
Attach side rails (C) to the headboard panel (A). Use Allen wrench (Y) to insert bolts (R) through washers (S, T) and into the pre-drilled holes. Do not fully tighten bolts yet. Repeat for both sides. (x2)
⚠️ Important Safety Notice
- Always use proper tools.
- Follow the assembly steps in order. Do not skip any steps.
- Check all packing materials carefully for small parts that may have come loose inside the carton during shipment. If parts are missing, contact the retailer from which you purchased the product. Do not use substitute parts.
- Periodically check to ensure that all connectors (bolts, screws, etc.) are tight.
- Keep the instructions for future reference.
- When assembling products that have glass or mirrors, be very careful handling them, as severe injury may result if glass or mirrors break. Never handle large pieces of glass or mirrors by yourself.
- When assembling products with electric cords (lamps, lights, etc.), always ensure (1) the electrical cord is unplugged before assembly and (2) be careful not to twist the electrical cord during assembly.
- When assembling shelves or entertainment centers, do not stand on lower shelves to assemble upper shelves; use a step ladder.
- Do not stand on tables, including but not limited to, end tables, coffee tables, and dinner tables, as tables are not designed to support the weight of a person.
- Where assembly instructions state that assembly requires two or more people, do not attempt by yourself as there is a risk of injury.
- Ashley Furniture Industries, LLC disclaims any liability for damages or injuries which may occur due to failure to properly follow assembly instructions, properly assemble the product, or properly use the product.
- Note: Your unit may look different in appearance from the one shown in the illustrations on this instruction sheet.
Parts List
Note: All parts required for assembly of this bed are packed in the open space in the back of the headboard panel.
| Part Identifier | Description | Quantity |
|---|---|---|
| A | Headboard Panel | 1 |
| B | Foot Rail | 1 |
| C | Side Rail | 2 |
| E | Support Leg | 2 |
| G | Center Support Leg | 4 |
| H | Side Rail | 2 |
| J | Side Rail | 2 |
| K | Cross Slat | 4 |
| L | Support Beam | 2 |
| M | Mounting Bracket | 2 |
| N | Mounting Bracket | 2 |
| P | Bolt (5/16" x 20mm) | 16 |
| R | Bolt (5/16" x 60mm) | 6 |
| S | Washer | 24 |
| T | Washer | 24 |
| U | Adjustable Leveler | 2 |
| W | Bolt (5/16") | 2 |
| Y | Allen Wrench | 1 |
| Z | Washer | 1 |
| AA | Screw | 4 |
| AB | Screw | 32 |
| AC | Screw | 26 |
| AD | Screw | 30 |
| AE | Bolt (1/4" x 80mm) | 2 |
Assembly Steps
Step 2
Attach side rails (C) to the headboard panel (A) using bolts (T, S, P) and Allen wrench (Y). Ensure all bolts are started before tightening. (x2)
Step 3
Attach support legs (E) to the side rails (B). Insert bolts (AE) through washers (S, T) and into the support legs (E) and side rails (B). Use Allen wrench (Y) to secure. (x2)
Step 4
Attach the foot rail (B) to the side rails (C). Use bolts (T, S, P, Y) and Allen wrench (Y) to secure. Ensure all bolts are started before tightening.
Step 5
Attach mounting brackets (M, N) to the side rails (H, J). Insert bolts (S, T) through the brackets and into the side rails. Secure with nuts (P) using Allen wrench (Y). (x4)
Step 6
Attach cross slats (K) to the side rails (H). Use screws (AD, AB, AC) and Allen wrench (Y) to secure the slats. (x2)
Step 7
Attach cross slats (J) to the side rails (H). Use screws (F, AC, AD, AB) and Allen wrench (Y) to secure the slats. (x2)
Step 8
This step shows the overall bed frame assembly with the headboard (A), foot rail (B), side rails (H, J), and cross slats (K, J) connected. Ensure all connections are stable.
Step 9
Attach adjustable levelers (U) to the bottom of the center support legs (G). Use bolts (AB, Z) and washers (AD, AC) with Allen wrench (Y) to secure. Ensure the levelers are positioned to allow for a 6mm space between the leveler and the floor when the bed is standing.
Step 10
Attach the center support legs (G) to the cross slats (C). Use screws (AA, AD, AB) and Allen wrench (Y) to secure the legs to the slats. (x4)
Step 11
The bed is now fully assembled.
Note: Always disassemble the bed prior to moving to a new location.
Replacement Parts & Support
For replacement parts, please contact:
- Email: RTAParts@ashleyfurniture.com
- Website: www.ashleyfurniture.parts
- Phone: 1-844-966-0809
