BIGBIG WON Blitz Controller User Manual

01. ILLUSTRAZIONE DELLE PARTI (Illustration of Parts)

The BIGBIG WON Blitz controller features a symmetrical design with various buttons and input methods. The top view shows:

• Central area: BIGBIG WON logo, BLITZ branding, and language indicator (ITALIANO).
• Top: [Home Button] in the center, [Screenshot Button] on the right, and [Pairing Button] above the Home button.
• Left side: [Left Stick] (LS) and [D-pad]. A [Left Light Strip] is located below the stick.
• Right side: [Right Stick] (RS) and the primary action buttons [A/B/X/Y Buttons]. A [Right Light Strip] is located below the stick.
• Front face (below sticks): A row of buttons including [Turbo Button], [Mapping Button], [Channel Indicator], [FN Button], [Config Button], and [MACRO Button].
• Other features: [NFC Area] near the center.

The rear view of the controller shows:

• Shoulder buttons: [ZL Button] on the left and [ZR Button] on the right.
• Rear programmable buttons: [M4 Button] (top left), [M2 Button] (bottom left), [M3 Button] (top right), and [M1 Button] (bottom right).
• Connection port: A [USB-C Port] is located at the bottom center.

02. ACCENSIONE E SPEGNIMENTO (Power On and Off)

Press and hold the [Home Button] for 3 seconds to turn the controller on or off.

03. SINCRONIZZAZIONE (Synchronization)

The controller supports two synchronization methods: Bluetooth and wired connection.

Bluetooth Synchronization:

After powering on the controller, press and hold the [Pairing Button] for 3 seconds. The [Home Indicator] will flash rapidly, indicating it's in pairing mode. Once synchronization is successful, the [Home Indicator] will remain solid.

Note: The specific [Channel Indicator] that lights up in Switch mode depends on the order in which controllers are synchronized with the console.

Wired Synchronization:

After powering on the controller, use the [USB-C Cable] to connect and synchronize the controller to the console.

Note: The controller supports Switch mode and XInput mode. To use it normally, you must switch to the corresponding console mode after synchronization. The default setting is Switch mode.

Steam Platform:

In the Steam desktop client, navigate to "Settings" -> "Controller" -> "General Controller Settings" and select "Xbox Configuration Support". Failure to do so may result in the game not recognizing the controller.

Switch Platform:

After wired synchronization with Switch, you need to enable "System Settings" -> "Controllers and Sensors" -> "Pro Controller Wired Communication".

04. COMMUTAZIONE DI MODALITÀ (Mode Switching)

The controller supports Switch and XInput modes. To use it normally, you must switch to the corresponding mode after synchronization.

• To switch to Switch mode: Press and hold the [A Button] + [Home Button] for 3 seconds until the [Home Indicator] turns red.
• To switch to XInput mode: Press and hold the [B Button] + [Home Button] for 3 seconds until the [Home Indicator] turns green.

Note: For Bluetooth synchronization with iOS and Android platforms, the controller must be in XInput mode.

05. MAPPATURA (Mapping)

The controller features four expandable rear buttons ([M1]-[M4]) and supports button mapping settings.

To Set Mapping:

Press the [Mapping Button] + one of the rear buttons ([M1]/[M2]/[M3]/[M4]). The [FN Indicator] will flash, indicating mapping mode.

Press the front button you wish to map to the selected rear button ([M1]/[M2]/[M3]/[M4]). The [FN Indicator] will flash twice to confirm the mapping.

To Clear Single Mappings:

Press and hold the rear button ([M1]/[M2]/[M3]/[M4]) you want to unmap, then double-click the [Mapping Button]. The [FN Indicator] will flash twice, indicating the current button mapping has been cleared.

To Clear All Mappings:

Double-click the [Mapping Button] directly. The [FN Indicator] will flash twice, indicating all button mappings have been cleared.

06. FUNZIONE TURBO (Turbo Function)

The controller supports the Turbo function for buttons including [A/B/X/Y Buttons], directional buttons (⬆️⬇️⬅️➡️), shoulder buttons ([L Button]/[R Button]/[ZL Button]/[ZR Button]), and rear buttons ([M1]-[M4]), totaling 16 buttons.

Setting Turbo:

Press and hold the [Turbo Button] + the button you want to set Turbo for. The [FN Indicator] will flash twice to confirm success. (The [FN Indicator] will flash at the current Turbo frequency during Turbo operation).

To Clear Single Turbo:

Press and hold the button you want to clear Turbo from, then double-click the [Turbo Button]. The [FN Indicator] will flash twice, indicating the Turbo setting for the current button has been cleared.

To Clear All Turbo Settings:

Double-click the [Turbo Button] directly. The [FN Indicator] will flash twice, indicating the Turbo setting for all buttons has been cleared.

Turbo Frequency:

Press and hold [FN Button] + ➡️ to cycle through frequencies: 5/s, 10/s, and 20/s. The default setting is 5/s.

07. REGISTRAZIONE DI MACRO (Macro Recording)

This controller supports macro recording. Each macro sequence must be linked to a rear button ([M1]-[M4]) as the activation trigger. Supported buttons for recording include [A/B/X/Y Buttons], directional buttons (⬆️⬇️⬅️➡️), shoulder buttons ([L Button]/[R Button]/[ZL Button]/[ZR Button]), [Left Stick] (LS), [Right Stick] (RS), and eight directions of the analog sticks. The setting method is as follows:

Macro Recording:

Press and hold the [Macro Button] + one of the rear buttons ([M1]/[M2]/[M3]/[M4]) for 3 seconds. The [FN Indicator] will flash, indicating macro recording mode.

Press the controller buttons to record the macro sequence. Click the [Macro Button] when recording is complete. The [FN Indicator] will flash twice to end the recording. (The [FN Indicator] will flash slowly during macro execution until completion).

To Clear a Single Macro:

Press and hold the rear button ([M1]/[M2]/[M3]/[M4]) to clear the macro, then double-click the [Macro Button]. The [FN Indicator] will flash twice, indicating the macro setting for the current button has been cleared.

To Clear All Macros:

Double-click the [Macro Button] directly. The [FN Indicator] will flash twice, indicating that the macro settings for all buttons have been cleared.

08. COMMUTAZIONE DELLA CONFIGURAZIONE DI INTEGRAZIONE (Configuration Switching)

Switch Mode:

Clicking the [Config Button] changes the [Channel Indicator] from red to white, indicating you are in configuration switching mode. The four indicators in this mode represent four different integration configurations.

Clicking the [Config Button] again initiates configuration switching. The indicators will cycle from top to bottom. The illuminated indicator represents the currently active integration configuration set.

If no configuration is switched within 5 seconds, the mode will automatically exit, and the indicator will change from white back to red, indicating the channel.

XInput Mode:

In this mode, there is no channel indication function. The indicator is white by default and shows the current integration configuration. Configuration can be switched directly in this mode by clicking the [Config Button].

09. COMMUTAZIONE DELLA ZONA MORTA DEL CONTROLLER (Controller Dead Zone Switching)

The controller is designed for esports, with a factory default dead zone of 0 for maximum control precision. However, this may cause slight drift in games without dead zones. To accommodate a wider range of users, two dead zones (0/10) are available.

Press and hold [FN Button] + [Left Stick Down] or [Right Stick Down] to switch between dead zones 0/10 for the left and right sticks, respectively.

10. CALIBRAZIONE DELLO STICK (Stick Calibration)

If you experience severe stick drift or the stick cannot reach its maximum value, try calibrating the stick as follows:

1. Press and hold the [Plus Button] + [Minus Button] simultaneously for 3 seconds. The [Left Light Strip] and [Right Light Strip] will illuminate and pulse orange, indicating calibration mode.
2. Push the sticks to their limits and rotate them in a uniform circle 3-5 times.
3. Then, press and hold the [Plus Button] + [Minus Button] simultaneously again. The [Left Light Strip] and [Right Light Strip] will flash twice and turn off, indicating calibration is complete.

11. CALIBRAZIONE DEL GIROSCOPIO (Gyroscope Calibration)

If the gyroscope is drifting, attempt calibration as follows:

1. Place the controller on a smooth, stable surface. Press and hold the [Plus Button] + [Screenshot Button] simultaneously. The [Left Light Strip] and [Right Light Strip] will pulse violet, indicating calibration mode.
2. Wait a moment. When the [Left Light Strip] and [Right Light Strip] flash violet twice, calibration is complete.

12. REGOLAZIONE DELLE VIBRAZIONI (Vibration Adjustment)

The controller supports four levels of vibration adjustment, managed as follows:

Press [FN Button] + ➡️ to cycle through vibration levels: Strong, Medium, Weak, and Off.

13. ISTRUZIONI PER LA BATTERIA (Battery Instructions)

When the battery is low, the light strip on both sides of the controller will flash red 10 times at a rate of 2 times per second to alert the user.

When the battery is connected to power, the controller's light strip will illuminate red, indicating it is charging. When the battery is fully charged, the charging light effect will turn off, and the light strip will return to its original state.

Charging Dock:

The charging dock has no light indication in standby mode. When the controller is connected to the dock:

• If the dock's RGB indicator cycles through seven colors, the controller is charging.
• If the dock's RGB indicator is solid green, the controller battery is fully charged.

14. ISTRUZIONI OPERATIVE DETTAGLIATE (Detailed Operating Instructions)

For a video guide, visit the official website's "Support Page": https://www.bigbigwon.com/support

15. I VOSTRI DIRITTI (Your Rights)

Limited warranty of 12 months from the date of purchase.