Lian Li UNI FAN SL-INF RGB Installation Guide

Package Contents

• UNI FAN SL-INF RGB fans (x3)
• UNI FAN SL-INF RGB fans (x4)
• UNI FAN SL-INF RGB fans (x12)
• Cables (x1)
• Cables (x1)
• Cables (x1)
• Cables (x1)

Fan to Fan Connection

Follow these steps to connect the fans to each other:

1. Connect the first fan.
2. Connect the second fan to the first.
3. Secure the connection.
4. Release the connection.
5. Fixed connection.
6. Release connection.

Power Module Installation

Note: The socket for the power module has different sizes. Please be aware of the direction.

Attention: The fan interlocking key is removable if it is affected by the radiator inlet and outlet. Please remove the fan interlocking key if necessary.

Attention: If the radiator inlet and outlet affect the fan interlocking key, you can remove the fan interlocking key.

Note: The top cover is removable if it is affected by the radiator inlet and outlet, and route the cable vertically.

Attention: If the radiator inlet and outlet affect the top cover of the power module, you can remove the top cover to route the cable vertically.

Steps to Switch Orientation of the Cable on the Power Module

1. Remove the cable.
2. Release the cable.
3. Fixed position.
4. Release the cable.
5. Fixed position.
6. Fixed position.

Remove the Fan Interlocking Key

Note: The fan interlocking key is removable if it is affected by the radiator inlet and outlet. Please remove the fan interlocking key if necessary.

Attention: If the radiator inlet and outlet affect the fan interlocking key, you can remove the fan interlocking key.

Use of Magnetic Adhesive Pad

Remove the adhesive backing.

Controller Cable Connection

Connect the controller to the fan splitter or directly to the fan.

Warning: Do not connect the wrong type of LED connector. If it is connected to the 12V connector, permanent damage will occur.

• Connect to 1, 2, 3, or 4, or splitter cable.
• Connect to 5V ARGB 3-pin header.
• Connect to USB.
• Connect to PSU SATA 15-pin.

Note: Press and pull out the connector to release the cable.

Attention: Press and pull the connector to release the cable.

Restriction of Controller

Maximum output of controller when connected BOTH SATA 15 PIN cable:

1. The maximum total output of the controller supports up to 29W.
2. Use L-Connect 3 to set static white, please lower the brightness.
3. When syncing to the motherboard and setting as 100% brightness of static white, the controller supports up to 8 UNI FAN SL Infinity.
4. Each SM type port supports up to 5W. (There are 2 SM type ports on the controller)

Controller Maximum Output with both SATA 15 PIN cables connected:

1. Controller maximum output is 29W.
2. When using L-Connect 3 software to set the fan to static white, please reduce the brightness.
3. When synchronizing with the motherboard and setting to 100% static white brightness, the controller supports up to 8 UNI FAN SL Infinity fans.
4. The controller's SM type output ports support a maximum of 5W each (the controller has 2 SM type output ports).

Splitter / Splitter

Control with L-Connect 3:

Connect up to 8 UNI FAN SL Infinity with a splitter when set to static white. Lower the brightness if necessary.

Control with Motherboard software:

Connect up to 5 UNI FAN SL Infinity with a splitter when set to 100% brightness static white.

Using L-Connect 3 software to control lighting effects:

When using this adapter cable to connect 8 fans and set them to static white, please reduce the white light brightness.

Synchronizing motherboard lighting effects software:

When the brightness is set to 100% static white light mode, using this adapter cable supports up to 5 Infinity Fans.