SALTO XS4 Original+ Installation Guide
For EURO Mortise Locks & Tubular Latches
SALTO inspiredaccess
Product Overview & Specifications
This guide details the installation of the SALTO XS4 Original+ electronic lock, compatible with EURO mortise locks and tubular latches.
Supported Models: Ei4xx series, Ei4xxE5 series, Ei450 xx series, Ei451 xx, Ei461 xx, T4xx.. series, and Electronic Info Models (W40M, W40T, W40MH).
Ingress Protection (IP) Ratings:
- Ei4xx series: IP54 (Outside), IP44 (Inside)
- Ei4xxE5 series: IP56 (Outside), IP44 (Inside)
Key Dimensions:
The lock mechanism and mounting require specific dimensions, including approximately 121mm, 161mm, 145mm, 105mm, 20mm, and 40mm for various components and clearances.
Required Hole Diameters:
- Main mechanism hole: Ø25mm [Ø1"]
- Spindle/bolt hole: Ø14mm [Ø9/16"]
Door Thickness Compatibility:
| Item Reference | Door Thickness | Component Size | Quantity |
|---|---|---|---|
| 3 | 32-47mm | 35 mm | |
| 4 | 45-60 mm | 50 mm | |
| 6 | 60-75 mm | 30 mm | x2 |
| 7 | 75-90 mm | 45 mm | x2 |
| 9 | 90-105 mm | 30 mm | x4 |
| 1 | 105-120 mm | 45 mm | x4 |
| 2 | 35 mm | ||
| A | 32-53 mm | 35 mm | |
| B | 45 mm | ||
| 5 | 45 mm |
Note: Specific parts are required for doors exceeding 60mm [2-3/8"] thickness.
Components and Tools
Tools Required: TORX 20 (x2), TORX 20 (x1), TORX 20 (x2), ALLEN 3 (x2), BOLT (type/quantity varies).
Essential Components: Mortise Lock (not included), SALTO LT2Lxx Tubular Latch (for "A2" versions).
Important: Use only with SALTO compatible escutcheons.
Recommendation: Use a mortise lock with a maximum 4° pre-turn angle.
Installation Steps
Follow these steps for a successful installation:
1. Select Handing
Determine the correct handing (left/right) for the door handles.
2. Prepare Door and Install Lock
Drill required holes (Ø14mm [Ø9/16"] and MIN. Ø25mm [MIN. 1"]). Insert the mortise lock and the SALTO LT2Lxx tubular latch (if applicable) into the door edge.
Diagram Description: Shows the door preparation and insertion of the mortise lock and latch mechanism.
3. Attach Handles
Insert the spindle through the mortise lock. Fit the exterior and interior handles onto the spindle and secure them using the provided TORX or ALLEN screws.
Diagram Description: Illustrates the process of attaching the handles to the spindle and door, then tightening the securing screws.
4. Mount Escutcheons and Secure Mechanism
Place the escutcheons (cover plates) on the door and fasten the internal components of the lock mechanism. Ensure proper alignment.
Diagram Description: Shows the escutcheons being positioned and secured, completing the main assembly.
5. Critical Warning: Program Before Closing
[⚠️ WARNING] AT THIS POINT DO NOT CLOSE THE DOOR. PROGRAM THE LOCK FIRST. This multilingual instruction is crucial for initial setup.
Diagram Description: Highlights the critical step of programming the lock before closing the door, often indicated by a warning symbol.
6. Battery Installation
Install the required LR03 batteries into the lock unit, observing correct polarity. The diagram indicates "MAX.40"" which may relate to battery performance.
Diagram Description: Shows the battery compartment and the correct insertion of LR03 batteries.
7. Programming and Testing
Refer to the specific programming guide for your SALTO XS4 Original+ model to configure settings. After programming, test all functions.
8. Handling Incorrect Installation
A visual indicator [❌] may show an "Incorrecto" [Incorrect] status, signaling an issue with assembly or function that needs correction.
Battery Replacement
To replace batteries, open the battery compartment and insert new LR03 batteries with correct polarity, following the installation diagram.
Special Notes
- Hotel Application: The lock is suitable for Hotel Guest Room Lock applications.
- Door Thickness: For doors thicker than 60mm [2-3/8"], specific parts are required.
- Mortise Lock Compatibility: If using an LE7Sxx series mortise lock, an unplugging step may be necessary.
