ROVSUN SF57B-17A00 Electric Stove
Instruction Manual
Safety Information
Please read and understand this entire manual before attempting to assemble, operate, or install the product. If you have any questions regarding the product, please call customer service.
WARNING:
- Stove is heavy and should be assembled near its desired location.
- It is recommended that two people move the assembled stove to prevent injury.
Warning: Do not install unit on shelves, raised platforms, beds, blankets, pillows, etc. Keep combustible materials such as furniture, bedding, papers, clothes, and curtains at least 3 feet (914 mm) from the stove.
General Safety Precautions
- Read all instructions before using this appliance.
- This appliance is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this appliance. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 ft. (914 mm) from the front of this appliance and keep them away from the sides and rear.
- Extreme caution is necessary when any heater is used by or near children, invalids, or pets, and whenever the heater is left operating unattended.
- If possible, always unplug this appliance when not in use.
- Do not operate any heater with a damaged cord or plug, or after the appliance malfunctions, has been dropped, or damaged in any manner.
- Any repairs to this appliance should be carried out by a qualified service person.
- Under no circumstances should this appliance be modified. Parts having to be removed for servicing must be replaced prior to operating this appliance again.
- Do not use outdoors.
- This heater is not intended for use in bathrooms, laundry areas, and similar indoor locations. Never place this appliance where it may fall into a bathtub or other water container.
- Do not use this heater in elevated locations, such as on shelves, raised platforms, etc.
- Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord away from traffic areas and where it will not be tripped over.
- To disconnect this appliance, turn controls to the off position, then remove plug from outlet.
- Connect to properly grounded outlets only.
- This appliance, when installed, must be electrically grounded in accordance with local codes, with the current CSA C22.1 Canadian Electrical codes, or for USA installations, follow local codes and the National Electric Code, ANSI/NFPA No. 70.
- Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock, fire, or damage to the appliance.
- To prevent possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
- This appliance has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored. This appliance should not be used as a drying rack for clothing, nor should Christmas stockings or decorations be hung on or near it.
- Use this appliance only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
- Always plug heaters directly into a wall outlet/receptacle. An extension cord or re-locatable power tap (outlet/power strip) should never be used.
- Do not use this heater with missing, damaged, or broken legs.
- "SAVE THESE INSTRUCTIONS"
Electrical Connection
A properly grounded outlet is required. Preferably, the fireplace will be on a dedicated circuit, as other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is in operation. The unit comes standard with a 6 ft. (1.8 m) long, three-wire cord, exiting the right side of the fireplace. Always plug the unit into a wall outlet/receptacle. An extension cord or re-locatable power tap (outlet/power strip) should never be used.
Electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electrical shock, and injury to persons.
Do not use this fireplace if any part of it has been under water. Immediately call a qualified service technician to inspect the fireplace and replace any part of the electrical system which has been under water.
Grounding Instructions
This heater is for use on 120 volts. The cord has a plug as shown at (A) in Figure 1. An adapter as shown at (C) is available for connecting three-blade grounding-type plugs to two-slot receptacles. The green grounding lug extending from the adapter must be connected to a permanent ground, such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.
Figure 1: Grounding Diagram
- (A) shows a standard three-prong electrical outlet with a grounding pin, a metal screw, and the cover of a grounded outlet box.
- (B) shows a two-slot electrical outlet.
- (C) shows an adapter with a grounding lug designed to connect a three-prong plug to a two-slot receptacle. The grounding lug is intended to be connected to a grounding means, such as the metal screw on the outlet box cover.
- (D) shows a three-prong plug.
Package Contents
A line drawing of the electric stove unit is shown. The unit is labeled 'A'.
Line drawings of four identical legs for the stove are shown. The legs are labeled 'B'.
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | Electric Stove | 1 |
| B | Leg | 4 |
Hardware Contents (shown actual size)
A line drawing of a screw is shown. The screw is labeled 'AA'.
- Screw (AA) - Qty: 12
Stove Dimensions
A line drawing of the electric stove unit is shown, similar to the one on the cover page.
Technical Specifications
| Model | SF57B-17A00 |
|---|---|
| Material | Iron, glass |
| Power Supply | 120V-60Hz |
| Power | 1400W |
| Temperature | 68~95°F / 20~35°C |
| Work Decibel | approximately 40dB |
| Certification | CSA |
| Warranty | 1 year |
Preparation
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents above. If any part is missing or damaged, do not attempt to assemble the product. Contact customer service for replacement parts.
Estimated Assembly Time: 20 minutes
Tools Required for Assembly (not included): Phillips screwdriver
Assembly Instructions SF57B-17A00
- Lay stove (A) upside down on a padded surface with the underside accessible. Attach leg (B) to stove by inserting the tab on the top of the leg (B) into the corresponding slot on the bottom of the stove (A). Insert three screws (AA) into predrilled holes and tighten securely. Repeat with remaining three legs.
A diagram shows the underside of the stove (A) with a slot. A leg (B) is shown being inserted into the slot. Screws (AA) are indicated to be inserted into pre-drilled holes.
Operating Instructions
Read All Instructions Before Use
Check that the heater outlet grill is not covered or obstructed in any way, and make sure the power to the unit is switched on.
NOTE: When the heat function is used for the first time, a slight odor may be present. This is normal and should not occur again unless the heater is not used for an extended period of time.
Controls and Operation
A diagram shows a circular dial with temperature settings (25°C, 30°C, 35°C) and an OFF position. Next to it, a panel shows two switches labeled 'POWER' and 'HEAT'. Both switches have 'ON' and 'OFF' positions.
- Power Switch: The Power switch supplies power to all of the functions of the stove. This switch must be in the ON position for any functions to work.
- Heater On/Off Switch: Press the heating button to turn on and turn off the stove.
- When the main power switch is turned on, use the temperature button to select the different heat settings. The range is 68~95°F / 20~35°C.
Care and Maintenance
Cleaning
Always turn the heater OFF and unplug the power cord from the outlet before cleaning. Use a vacuum or duster to remove dust and dirt from the heater and vent areas. To maintain the finish, clean with a soft, slightly damp cloth and buff with a dry cloth. Never use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.
Never drag the unit across a floor. The added stress from dragging the unit may cause the legs to break.
Glass Information (some models)
- Under no circumstances should this product be operated with broken glass.
- Do not strike or slam the glass.
- Do not use abrasive cleaners to clean the glass.
- This product uses tempered glass. Replacement of the glass supplied by the manufacturer should be done by a qualified service person.
