ROVSUN SF310-36A WALL HANGING ELECTRIC FIREPLACE

Safety Information

Retain for future reference: Read carefully

1. Read all instructions before using this fireplace.
2. Always unplug this appliance when not in use.
3. Children should be advised not to play with this fireplace.
4. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Return the heater to an authorized service facility for examination, electrical or mechanical adjustment, or repair.
5. Any repairs to this appliance should be carried out by qualified/authorized service personnel only.
6. Under no circumstances should this appliance be modified. Parts having to be removed for servicing must be replaced with original "OEM" (original equipment manufacturers) parts only.
7. Do not use outdoors.
8. This appliance is not intended for use in bathrooms, laundry areas, and similar indoor locations. Never locate this appliance where it may fall into a bathtub or other water container.
9. Do not run the cord under carpeting. Do not cover the cord with throw rugs, runners, or the like. Arrange the cord away from traffic areas and where it will not be tripped over.
10. To disconnect the heater, turn controls to off, then remove the plug from the outlet.
11. Connect to properly grounded outlets only.
12. This appliance, when installed, must be electrically grounded in accordance with local codes, with the current CSA C22.1 Canadian Electric codes, or for USA installations, follow local codes and the National Electrical Code, ANSI/NFPA No. 70.
13. There is a thermostat limiter inside the fireplace. When the inner temperature over heats or abnormal heating occurs, the thermostat protective device will cut off the power supply to avoid damage to the fireplace or risk of fire.
14. This appliance has hot and arching or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored. This appliance should not be used as a drying rack for clothing, nor should Christmas stockings or decorations be hung on or near it.
15. Use this appliance only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
16. The use of an extension cord is not recommended due to risk of fire. If used, the extension cord shall be No. 14 AWG minimum size and rated no less than 1,875, and the extension cord shall be a three-wire cord with grounding type plug and cord connector. The extension cord shall not be more than 6m / 20 ft in length.
17. Do not use this appliance with a programmable timer or any other device that switches the appliance on and off automatically. In order to avoid a hazard due to inadvertent resetting of the thermal cut out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by a utility.
18. This product contains a button battery. If swallowed, it could cause severe injury or death in just 2 hours. Seek medical attention immediately.

⚠️ WARNING: This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this appliance. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 ft. (0.9 m) from front, sides and rear of the heater.

❗ CAUTION: Operate only on supplied stand or mount to wall. Do not install heater less than 60 cm / 23.6 in from the floor.

❗ CAUTION: When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons.

❗ CAUTION: To prevent a possible fire, do not block heater air intakes or the exhaust in any manner. Do not operate the heater on soft surfaces, like a bed, where openings may become blocked.

❗ CAUTION: Do not insert or allow foreign objects to enter any ventilation or exhaust openings, as this may cause an electric shock or fire, or damage to the heater.

❗ CAUTION: Extreme caution is necessary when any heater is used by or near children or invalids, and whenever the heater is left operating and unattended.

❗ IMPORTANT: SAVE THESE INSTRUCTIONS.

Pre-Installation

PLANNING INSTALLATION

Before you begin assembly, locate the instructions and hardware. Compare all parts with the Hardware Included and Package Contents lists. Be sure you have all the parts and can identify them. A helping hand is always good. Assemble your fireplace with an adult assistant if possible. Some pieces are heavy and will need to be held by a helper. Assembly time will take approximately 5-20 minutes.

Before assembly, use scissors to unwrap the parts from the packaging. Do not use a box cutter or exacto-knife, as you may cut into the heater pieces inside the box and damage the finish. Check for the red hardware bag located inside the packaging, taped to the top of the box. Do not discard any pieces. Use an appropriate screwdriver to insert and tighten all screws.

❗ CAUTION: This carton includes a GLASS panel! Always use extreme caution when handling glass. Failure to do so could result in personal injury or property damage.

SPECIFICATIONS

ELECTRICAL CONNECTION

⚠️ WARNING: Electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electrical shock, and injury to persons.

⚠️ WARNING: Do not use this fireplace if any part of it has been under water. Immediately call a qualified service technician to inspect the fireplace and replace any part of the electrical system which has been under water.

A 15 Amp, 120 Volt, 60 Hz circuit with a properly grounded outlet is required to operate this appliance. Preferably, the appliance will be on a dedicated circuit, as other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the fireplace is in operation. The unit comes standard with a 6 ft (1.8 m) long 3-wire cord, exiting out the back of the fireplace. Plan the installation to avoid the use of an extension cord. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).

GROUNDING INSTRUCTIONS

This heater is for use on 120 volts. The cord has a plug as shown at (A) in Figure 1. An adapter as shown at (C) is available for connecting three-blade grounding-type plugs to two-slot receptacles. The green grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.

Figure 1: Grounding Plug and Adapter Components

• (A) Standard 3-prong plug with grounding pin.
• (B) Grounded outlet box connection.
• (C) Adapter for connecting a 3-prong plug to a 2-slot receptacle. Includes a green grounding lug.
• (D) Grounding pin/lug.

Remote Control

This Class (B) device complies with Part 15 of the FCC Rules and Canadian ICES-003. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This remote control requires 1 Lithium Coin Cell Battery (size CR2025), which is included.

❗ CAUTION: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

⚠️ WARNING: DO NOT mix old and new batteries. DO NOT use rechargeable silver oxide cell batteries with remote control unit. DO NOT mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel-Cadmium) batteries. DO NOT dispose of batteries in fire. Improper disposal may cause batteries to leak or explode.

Pre-Installation (continued)

TOOLS REQUIRED (NOT INCLUDED)

• Safety goggles
• Phillips screwdriver ?
• Power drill ⚙️

HARDWARE INCLUDED

PACKAGE CONTENTS

NOTE: Both table top supports are identical.

Installation

Wall-Mount Installation

1. Positioning the mounting bracket

   Choose a solid wall. Position the mounting bracket (C) where the electric firebox (A) is to be installed on the wall, and ensure that the mounting bracket (C) is level. Use a pen to mark the 2 mounting holes on the wall at the desired mounting location, using the mounting bracket (C) as a template.

   Diagram Description: Shows mounting bracket (C) being held against a wall, with marks being made for screw holes. Arrows indicate leveling.

2. Securing the mounting bracket

   Insert the 2 self-drilling wall anchors (CC) into the wall where previously marked. If installing the mounting bracket (C) to a wall stud, there is no need to drill the holes in the wood and no need for the plastic wall anchors (CC). It is recommended to install the mounting bracket to at least one stud.

   Diagram Description: Shows wall anchors (CC) being inserted into a wall, and a screw (BB) being used to attach the bracket.

3. Securing the mounting bracket

   Secure the mounting bracket (C) to the wall using 2 large screws (BB).

   Diagram Description: Shows the mounting bracket (C) fully attached to the wall with screws (BB).

4. Hanging the electric firebox

   Hang the electric firebox (A) on the mounting bracket (C).

   Diagram Description: Shows the electric firebox (A) being hung onto the mounted bracket (C) on the wall.

5. Inserting the ember bed

   Arrange the ember beds (acrylic crystals [D], pebbles [E] or log set [F]) along the inset window ledge at the front of the electric firebox (A).

   Diagram Description: Shows the electric firebox (A) with the ember bed (F) arranged inside.

6. Installing the glass front

   NOTE: This glass front is heavy. It is recommended that you use two people at this stage to prevent damage to the glass front or the electric firebox.

   Lift the glass front (B) into place, making sure the 2 tabs on the top back of the glass front (B) fit securely into the holes on the top of the electric firebox (A).

   Secure the glass front (B) by fastening two small screws (AA) on both sides.

   Diagram Description: Shows the glass front (B) being attached to the electric firebox (A) with small screws (AA).

Table Top Installation

1. Assembling the Table Top Stand

   Attach the deflector (H) to the front (I) using 2 small screws (AA). Slide the whole part on to the table top base (J). Attach the left and right table top supports (G) to the table top base (J) using 4 screws (AA).

   Diagram Description: Shows components H, I, J, and G being assembled using screws (AA) to form the table top stand.

2. Securing the mounting bracket

   Use a screwdriver to secure the mounting bracket (C) to the table top stand with 2 small screws (AA).

   Diagram Description: Shows the mounting bracket (C) being attached to the assembled table top stand using screws (AA).

3. Securing the electric firebox

   Using a screwdriver, secure the electric firebox (A) to the mounting bracket (C) with 2 small screws (AA).

   Diagram Description: Shows the electric firebox (A) being attached to the mounting bracket (C) on the table top stand using screws (AA).

4. Inserting the ember bed

   Arrange the ember beds (acrylic crystals [D], pebbles [E] or log set [F]) along the inset window ledge at the front of the electric firebox (A).

   Diagram Description: Shows the electric firebox (A) with the ember bed (F) arranged inside.

5. Installing the glass front

   NOTE: This glass front is heavy. It is recommended that you use two people at this stage to prevent damage to the glass front or the electric firebox.

   Lift the glass front (B) into place, making sure the 2 tabs on the top back of the glass front (B) fit securely into the holes on the top of the electric firebox (A).

   Secure the glass front (B) by fastening two small screws (AA) on both sides.

   Diagram Description: Shows the glass front (B) being attached to the electric firebox (A) on the stand using small screws (AA).

Operation

USING THE MANUAL AND REMOTE CONTROLS

On the top-right side plate of the electric fireplace (A) is the control panel. This panel contains the buttons to properly operate the electric fireplace. The buttons on the control panel on the side of the electric fireplace (A) and the remote control (K) function in the same way. The remote control has an effective range of up to 13 ft.

Control Panel Buttons:

• 1. Power Button ?
• 2. Flame Control Button ?
• 3. Heater Control Button ?️
• 4. Timer Control Button ⏱️
• 5. Side Light Control Button ?
• 6. Heater on / off Switch
• 7. Ember Bed Control Button
• 8. Digital Display Panel

USING THE POWER BUTTON

The main power button (1) is located on the control panel on the side of the electric fireplace.

• Pressing the power button (1) once turns the power on.
• Pressing the power button (1) again will turn the power off.
• If you find that none of the other buttons appear to work, check to make sure that the main power (1) is turned on.

USING THE FLAME CONTROL BUTTON

Press the flame control button (2) to turn on the ember bed and flame effect. Pressing the flame control button (2) once turns flames on and lights the ember bed. Pressing the flame control button (2) again will cycle through different colors of the ember bed. The color rotation mode will cycle through different color settings continuously. Reference the table for more detailed information.

BATTERY REPLACEMENT

Uses a 3 Volt lithium coin cell type CR2025 battery.

Diagram Description: Shows the remote control battery compartment being opened and a CR2025 battery being replaced.

⚠️ WARNING: This product contains a button battery. If swallowed, it could cause severe injury or death in just 2 hours. Seek medical attention immediately.

USING THE THERMOSTAT CONTROL BUTTON

Pressing the heat button (3) once turns the heater fan on.

Press and hold the heater button for 5 seconds to enter the temperature mode. After 5 seconds press the heat button to cycle through the different heat settings. Continue to press the heat button to cycle through the different heat settings.

Once the desired room temperature is reached the heater fan will deactivate.

Reference the table for more information.

To display the temperature setting in either Fahrenheit or Celsius, press the heat button (3) of control panel once, then press and hold the power button (1) of control panel for 5 seconds. The display will beep and switch between Fahrenheit or Celsius.

USING THE TIMER CONTROL BUTTON

Pressing the timer control button (4) will set the timer. This interval period is shown in the display (8) on the control panel on the side of the electric fireplace. The set intervals are as listed in the table.

NOTE: If this product experiences exceptionally high temperature, it may automatically stop heating. If this occurs the product should be unplugged or isolated from the main supply for a period of 5 minutes before the power is then resupplied.

ADJUSTING THE AMBIENT SIDE LIGHTING

Press the side light control button (5) to turn on the ambient lighting.

To change the color of the lighting press the side light control button (5) again. You can control the side lights color as described in the table. The color rotation mode will cycle through different color settings continuously.

HEATER LOCKING FUNCTION

To turn off heat mode, press and hold the flame button for 5 seconds to enter heat lock out mode. Flame lights will flash 5 times to signal the heat function is turned off and locked out. To turn on heat mode, press and hold the heat button for 5 seconds. The flame lights will flash 5 times and the heat function will be restored. When the heat button is pressed in lock out mode, the ember bed will flash 5 times until the heating mode is turned on.

USING THE EMBER BED / LOGSET CONTROL BUTTON

Pressing the ember bed control button (7) once will light the ember bed. Continue to press the ember bed control button (7) to cycle through different colors of the ember bed. Reference the table for more information.

Care and Cleaning

❗ IMPORTANT: Always unplug the power cord before cleaning the unit. Allow the unit to cool before cleaning it.

• Wipe the exterior surface of the electric firebox occasionally with a soft, damp cloth (not dripping wet), and dry the exterior surface before operating.
• Do not immerse the electric fireplace in water.
• Do not use any cleaning chemicals such as detergents and abrasives.
• Do not allow the interior to get wet, as this could create a hazard.
• Light accumulated dust may be removed from the electric fireplace with a soft, dry cloth.
• To store the electric fireplace, put it back into its original packaging and store in a clean, dry place.
• The blower and flame motor are pre-lubricated for a durable using time and need no further lubrication or maintenance. Dust particles will accumulate on/in the electric fireplace, so periodic cleaning/vacuuming of the electric fireplace is recommended.
• Always turn the heater OFF and unplug the power cord from the outlet before cleaning.
• Cleaning of the control panel, located in the upper right-hand corner of the fireplace behind the sliding control panel cover, is to be done only using a soft cloth, slightly dampened in water (if needed, a small amount of dish soap can be added to the water) and dried using a clean, dry soft cloth. Cleaning of the screen diffuser is to be done using only water and lint free cloth. DO NOT use any abrasive on the controls and the diffusing screen.