Manuals+
Teltonika RUTX12 Quick Start Guide

TELTONIKA | Networks

RUTX12

Quick Start Guide v1.1

For more information, visit the Wiki knowledge base: https://wiki.teltonika-networks.com/

Device Overview

Front View

The front panel features several indicators, ports, and slots:

  • Mobile network type LEDs: Indicate the type of mobile network connection (e.g., 2G, 3G, 4G).
  • Mobile signal strength indication LEDs: Display the quality of the mobile network signal.
  • WAN type LEDs: Show the status of the Wide Area Network connection.
  • SIM holders (x2): Slots for inserting SIM cards.
  • SIM needle: A tool used to eject the SIM card holders.
  • Power socket: Connection point for the power adapter.
  • WiFi band LEDs: Indicate activity on the 2.4 GHz or 5 GHz WiFi bands.
  • LAN Ethernet ports (x4): Labeled LAN1 through LAN4, for wired local area network connections.
  • WAN Ethernet port: For connecting to a Wide Area Network.
  • Power LED: Indicates the device's power status.
  • Reset button: Used to reset the device to its default settings.

Back View

The back panel contains antenna connectors, a USB port, and a grounding screw:

  • Mobile MAIN antenna connector for SIM1/SIM2: Primary antenna connections for mobile networks.
  • Mobile AUX antenna connector for SIM1/SIM2: Auxiliary antenna connections for mobile networks.
  • GPS antenna connector: For connecting a GPS antenna.
  • WiFi antenna connectors: For connecting WiFi antennas.
  • Bluetooth antenna connector: For connecting a Bluetooth antenna.
  • USB port: For connecting USB devices.
  • Grounding screw: For securing a grounding connection for safety.

Hardware Installation

Power Socket Pinout

The power socket has four pins for connecting the power adapter:

  • Power / Red wire: Positive power connection.
  • Ground / Black wire: Ground connection.
  • Input / Green wire: Input signal or data.
  • Output / White wire: Output signal or data.

Installation Steps

  1. Pull out the SIM needle from the front panel of the router.
  2. Push the SIM holder button with the SIM needle.
  3. Pull out the SIM holder.
  4. Insert your SIM card into the SIM holder.
  5. Slide the SIM holder back into the router.
  6. Attach all antennas to their respective connectors.
  7. Connect the power adapter to the socket on the front of the device, then plug the other end into a power outlet.
  8. Connect to the device wirelessly using the SSID and password provided on the device information label, or use an Ethernet cable connected to a LAN port.

Login and Configuration

Accessing the Web Interface

  1. Open your internet browser and type http://192.168.1.1 into the URL field.
  2. When prompted for authentication, use the default login information (refer to the device information label or documentation).
  3. Upon first login, you will be required to change your password for security reasons. The new password must contain at least 8 characters, including at least one uppercase letter, one lowercase letter, and one digit. This step is mandatory.
  4. After changing the password, the Configuration Wizard will start, guiding you through the setup of the router's main operating parameters.
  5. Navigate to the 'Overview' page and pay attention to the 'Signal Strength' indication. To maximize cellular performance, try adjusting the antennas or changing the device's location to achieve the best signal conditions.

Example Login Screen (Image A): Shows fields for username and password, with a 'Login' button. Default username is typically 'admin', and a default password may be provided.

Example Mobile Status (Image B): Displays connection details such as 'Data connection state' (e.g., Connected), 'State' (e.g., Registered; OPERATOR; 4G (LTE)), 'SIM card slot in use' (e.g., Ready), and 'Bytes received/sent'.

Technical Information

Radio Specifications

Specification Details
RF technologies 3G, 4G, GNSS, WiFi, BLE
Max RF power 24 dBm@WCDMA, 23 dBm@LTE, 23 dBm@WiFi, 10 dBm@BLE

Bundled Accessories Specifications*

Accessory Specifications
Power adapter Input: 0.6 A@100-240 VAC, Output: 12 VDC, 1.5 A, 4-pin plug
Mobile antenna 698~960/1710~2690 MHz, 50 Ω, VSWR<3, gain** 3 dBi, omnidirectional, SMA male connector
GNSS antenna 1575.42~1602 MHz, 2.2~5 VDC, VSWR<1.5, active total gain** 28 dB (typ.), RHCP polarization, SMA male connector
WiFi antenna 2400~2500 MHz/4950~5850 MHz, 50 Ω, VSWR<2, gain** 3 dBi, omnidirectional, RP-SMA male connector
BLE antenna 2400~2500 MHz, 50 Ω, VSWR<2.5, gain** 2.5 dBi, omnidirectional, RP-SMA male connector

*Order code dependent.

**Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for the compliance with the legal regulations.

Safety Information

The RUTX12 router must be used in compliance with any and all applicable national and international laws and with any special restrictions regulating the utilization of the communication module in prescribed applications and environments.

EU Declaration of Conformity

Hereby, TELTONIKA declares that this RUTX12 is in compliance with the essential requirements and other relevant provisions of Directive CE/RED.

The full text of the EU declaration of conformity is available at the following Internet address: https://wiki.teltonika-networks.com/view/RUTX12_CE/RED

Instruction Manual Excerpt

Connect the power adapter to turn on the device. Open http://192.168.1.1 in your web browser to configure it. More information on https://wiki.teltonika-networks.com

Symbols and Compliance

[WEEE symbol] This sign means that all used electronic and electric equipment should not be mixed with general household waste.

[CE mark] This sign means that the product meets the requirements of the applicable EU directives.

Models: RUTX12, Dual LTE CAT6 Router, RUTX12 Dual LTE CAT6 Router

File Info : application/pdf, 6 Pages, 276.14KB

QSG RUTX12 EN-v1.1

References

Adobe PDF library 15.00 Adobe Illustrator 24.2 (Windows)

Related Documents

Preview Teltonika OTD140 Industrial 4G LTE Router Datasheet
Comprehensive datasheet for the Teltonika OTD140, a robust industrial 4G LTE router. Discover its features, hardware specifications, network capabilities, security protocols, and physical dimensions for industrial IoT and connectivity solutions.
Preview Teltonika RUTX11 Quick Start Guide - Installation and Configuration
This document provides a quick start guide for the Teltonika RUTX11 industrial cellular router, covering hardware installation, device login, technical specifications, and safety information.
Preview Teltonika Networks RUT901 Quick Start Guide
This Quick Start Guide provides essential information for setting up and using the Teltonika Networks RUT901 router, including safety precautions, technical specifications, hardware installation, and initial configuration steps.
Preview Teltonika Networks RUT955 Industrial Cellular Router Datasheet
Detailed datasheet for the Teltonika Networks RUT955, an industrial-grade 4G LTE router with WiFi, Ethernet, and multiple I/O options. Features include robust connectivity, security, and remote management capabilities.
Preview Teltonika RUT950 Industrial Cellular Router Datasheet
Comprehensive datasheet for the Teltonika RUT950 industrial cellular router, detailing its hardware specifications, features, network capabilities, security, IoT platform integration, physical dimensions, regulatory approvals, and mounting options. Includes technical specifications, order codes, and available versions.
Preview Teltonika TRB141 Quick Start Guide: Setup and Configuration
A concise guide to setting up and configuring the Teltonika TRB141 LTE CAT 1 IoT Gateway, covering hardware installation, device configuration, and technical specifications.
Preview Teltonika RUT301 Datasheet: Industrial Router Specifications
Comprehensive datasheet for the Teltonika RUT301 industrial router, detailing its hardware, features, network capabilities, security, power, physical specifications, and operating environment.
Preview Teltonika RUT950 Quick Start Guide
A concise guide to setting up and configuring the Teltonika RUT950 LTE router, including hardware installation, login procedures, technical specifications, and safety information.