EPIC FUTUREPROOF
USER MANUAL
[DIGITAL DOOR LOCK]
Model: ES-T153
Safety Precautions
- Please do not repair the product by yourself.
- Please check environment before installation.
- Please read the manual carefully before using.
- Please change your pin number periodically.
- Please do not knock or apply force on the lock.
- Protect the product from wetness & moisture.
- Please replace with new batteries all-at-once.
- Clean the lock with clean dry cloth.
- Please use the product correspondingly.
Product Dimension
| Items | Descriptions |
|---|---|
| Installation conditions | Door thickness: 40~50mm |
| Authentication Method | No. of pin number: 4~12 digits |
| Power supply | LR 6 AA ALKALINE (X4)EA |
| Emergency Battery | DC 9V ALKALINE BATTERY (Sold separately) |
| Temperature | Sensor temperature: 72°C±5°C Maximum Temperature, 62°C±5°C Normal Temperature |
| Material | Outer body: Al, Zn, ABS Inner body: Zn, ABS |
Product Specifications
| Items | Frequency | Channel | Module | Public line power |
|---|---|---|---|---|
| RFID | 13.56 MHz | 1 EA | ASK | 93.5 dBuV/m@10m Below |
| Remote device | 447.275 MHz | 1 EA | FSK | 10mW Below |
Product Description (Outer body)
This section describes the outer unit of the digital door lock. It features a number pad (0-9, *, #), a card reader labeled "CARD", a reset button, a status LED lamp, a battery lamp, and an emergency battery terminal. A 9V emergency battery ?, sold separately, can be connected via the emergency battery terminal.
[FCC logo] This equipment has been tested and found to comply with the limits for a Class B digital device.
Contact: ✉️ info@epic.co.kr | ? www.epic.co.kr
This product should be installed by a skilled installer only. To receive full coverage of the product warranty, please do not install by yourself for safety purposes.
Document Revision: PTSP4420ONTA REV.01
Product Description (Inner body)
This section describes the inner unit of the digital door lock. Key components include the deadbolt, door closing sensor, manual lock knob, open/close button, registration button, and the compartment for alkaline AA batteries. The battery cover is also visible.
Pin Number Registration
⚠️ Caution: Always register pin number while the door is open. The default pin number upon purchase is [1, 2, 3, 4].
❗ Warning: Please do not forget the pin number at all times. Once forgotten, you will not be able to register a new pin or card. There is no pin number reset.
To change existing pin number
- Open battery cover. Press [Registration] button once. A ~beep sound ? will be heard.
[Image: Battery compartment with registration button]
- Enter current pin number followed by the [*] button. Press number [1] button.
[Image: Finger pressing number pad]
- Enter new pin number (4-12 digits). Press [*] button on the number pad. A melody ? will be heard and the registration is complete.
[Image: Finger pressing number pad with sound waves]
⚠️ Caution: Please register pin number within 10 seconds after pressing the registration button, or the registration process will be cancelled. New registration of a single pin number will delete all previously registered pin numbers on the system.
RFID Card Registration (all-at-once)
⚠️ Caution: New RFID cards are registered without erasing previous registration records. RFID cards included inside the box are not registered in default. Only compatible cards can be registered and used.
- Open battery cover. Press [Registration] button once. ~beep sound ? will be heard.
[Image: Battery compartment with registration button]
- Enter current pin number, followed by the [*] button.
[Image: Finger pressing number pad]
- Press number [2] button.
[Image: Finger pressing number pad]
- Place the card to be registered on the card reader. The beep sound ? will be heard, and the saved 3-digit location number (001~100) will be displayed on the number pad.
[Image: RFID card placed on reader]
- Press [Registration] button after all cards have been registered and the registration is complete.
[Image: Battery compartment with registration button]
Note
Up to 100 RFID cards can be registered. To register multiple RFID cards, repeat step 4 before the number pad turns off. Place RFID cards on the card reader within 10 seconds after pressing [Registration] button or the registration process will be cancelled. No more RFID cards can be registered after the 100th registration.
RFID Card Registration (one-by-one)
⚠️ Caution: The card location number should be from 001~100 and must consist of 3 digits always. When it is not individual card registration, pressing [*] button will enable normal registration mode.
- Open battery cover. Press [Registration] button once. ~beep sound ? will be heard.
[Image: Battery compartment with registration button]
- Enter current pin number, followed by the [*] button.
[Image: Finger pressing number pad]
- Press number [2] button.
[Image: Finger pressing number pad]
- Enter the card location number consisting of 3 digits (001~100), followed by the [*] button.
[Image: Finger pressing number pad]
- When the number pad arrow is displayed, it is in RFID card entry standby status. Place the card to be registered on the card reader. The beep sound ? will be heard, and the saved 3-digit location number will be displayed on the number pad.
[Image: RFID card placed on reader]
- To register additional RFID cards: When all numbers on the pad are lit, enter a new location number, followed by the [*] button, then register the new card.
When there are no additional cards to be registered: Press [Registration] button to complete the registration.[Image: Battery compartment with registration button]
RFID Card Deletion (all-at-once)
- Open battery cover. Press [Registration] button once. ~beep sound ? will be heard. Enter current pin number, followed by the [*] button.
[Image: Battery compartment with registration button]
- Press number [8] button followed by the [*] button.
[Image: Finger pressing number pad]
- Long press [*] button for 5 seconds. When the melody ? is heard, All RFID cards are deleted.
[Image: Finger pressing number pad, 5 Seconds text]
RFID Card Deletion (one-by-one)
- Open battery cover. Press [Registration] button once. ~beep sound ? will be heard. Enter current pin number, followed by the [*] button.
[Image: Battery compartment with registration button]
- Press number [8] button followed by the [*] button.
[Image: Finger pressing number pad]
- Enter the registered card location number, followed by the [*] button.
[Image: Finger pressing number pad]
- After deletion is complete, all numbers are lighted on the number pad. Additional card deletion is in standby mode. If there is no location number to be deleted, press [Registration] button.
[Image: Battery compartment with registration button]
