Victrola Journey Glow VSC-700SB Instruction Manual

Overview

The Victrola Journey Glow VSC-700SB is a turntable with various playback modes and features. The following diagram illustrates its components:

Diagram Description: A top and bottom view of the Victrola turntable with numbered callouts pointing to specific components.

• 1. Turntable Platter
• 2. Turntable Spindle
• 3. 45 RPM Adapter
• 4. Lift Lever
• 5. Tonearm Clip
• 6. Line-In Jack
• 7. Auto Stop Switch
• 8. Function Knob
• 9. Speed Selection Switch
• 10. Tonearm
• 11. Power / Volume Knob
• 12. LED Indicator
• 13. Stylus
• 14. Headphone Jack
• 15. GlowRGB (LED) Button
• 16. RCA Output
• 17. Power Adapter Input

Initial Setup

1. Place the unit on a flat and level surface and open the buckle.
2. Remove all packing materials, including the twist tie from the tonearm.
3. Remove the stylus cover by gently pulling it towards the front of the unit.
4. Using the included power adapter, plug in the unit.
5. Rotate the power knob to turn the unit ON.

Victrola GlowRGB™ Operation

The GlowRGB button controls the unit's LED lighting effects.

GlowRGB Button Functions:

• Press & Hold: Turn lights ON / OFF.
• Double Press: Switch Light Mode Group (Multicolor | Music Pulse | Solid Colors).
• Single Press: Switch Individual Light Modes.

Light Modes & Groups:

Multicolor Modes

• 1. Transition
• 2. Racetrack
• 3. Strobe
• 4. Snake
• 5. Waterfall
• 6. Chase

Music Pulse Modes

• 1. Red
• 2. Green
• 3. Blue
• 4. Yellow
• 5. Pink
• 6. Multicolor

Solid Color Modes

• 1. Red
• 2. Green
• 3. Blue
• 4. Yellow
• 5. Pink
• 6. White

Vinyl Mode

To play vinyl records:

1. Rotate the power knob to turn the unit ON.
2. Rotate the function knob to PHONO (Vinyl) mode.
3. Place a vinyl record on the platter.
4. Release the tonearm from the tonearm rest.
5. Raise the tonearm using the lift lever.
6. Move the tonearm over the edge of the record and lower the lift lever to begin playing.

Use the power/volume knob to adjust the volume.

Speed Selector Switch

Use this switch to adjust the record speed (33 1/3, 45, or 78 RPM). If using a 45 RPM record, use the included 45 adapter. Visual: A switch with markings for 33, 45, and 78 RPM.

Auto Stop Selection Switch

If this switch is ON, the record will start spinning when the tonearm moves over the record and will stop automatically when playback is finished. If OFF, the record spins when in "PHONO" mode and continues spinning after playback.

RCA Line Out

Use the red and white connectors on the back of the unit to connect to an amplifier/stereo device. Reduce the volume to a minimum level on the record player before connecting and increase volume as needed.

Headphones

Use the headphone jack on the platter to connect headphones/earbuds. Reduce the volume to a minimum level on the record player and increase volume as needed.

Note:

• Only touch the center or edges of the record to avoid damage to vinyl grooves.
• If no sound is playing, ensure the function knob is set to Vinyl mode.

Vinylstream™ Mode

Play a vinyl record on an external Bluetooth speaker or headphones.

1. Rotate the power knob to turn the unit ON.
2. Rotate the function knob to BT OUT (Vinylstream) mode. The unit will search for Bluetooth devices (LED flashes Blue).
3. Turn ON your external Bluetooth speaker or headphone and set it to pairing mode.
4. The unit will chime when connected (LED stops flashing).

Use your external device to control the volume.

Notes:

• In Vinylstream mode, internal speakers are disengaged.
• Place the Bluetooth device within 1m (3.3') for initial pairing.
• Ensure the unit is within 10m (33ft) of the external device for the strongest connection.

Bluetooth Mode

Connect to Bluetooth devices.

1. Rotate the power knob to turn the unit ON.
2. Rotate the function knob to BT (Bluetooth) mode. The unit will search for Bluetooth devices (LED flashes Blue).
3. On your device, turn on Bluetooth and select “Victrola Journey Glow” from the list.
4. The unit will chime when connected (LED stops flashing).

Use the Power/Volume Knob to adjust volume.

Notes:

• Ensure the unit is within 10m (33ft) of your external device for the strongest connection.
• If no sound is playing, ensure the function knob is set to Bluetooth mode.

Aux-In Operation

Connect an external audio device using a 3.5mm auxiliary cable (not included) to the LINE IN jack on the platter.

1. Rotate the power knob to turn the unit ON.
2. Rotate the function knob to LINE IN (Aux-In) mode (LED turns Purple).
3. Use the Power/Volume Knob to adjust volume. Use the controls on the external audio device for other playback functions.

Stylus Replacement

Removing the Stylus from the Tonearm

1. Place fingers at the tip of the stylus and push down towards direction "A". Warning: Applying excessive force may damage or break the cartridge.
2. Pull the stylus out towards direction "B".

Diagram Description: Shows stylus removal by pushing down (A) and pulling out (B).

Installing the Stylus (Replacement Stylus # ITNP-S1)

1. Hold the tip of the stylus and insert the other edge by pressing towards direction "C".
2. Push the stylus up towards direction "D" until it locks at the tip.

Diagram Description: Shows stylus installation by inserting at (C) and pushing up until locked at (D).

Note: The stylus should last about 300 hours under normal use. Replace the stylus when sound quality degrades.

Specifications

General

Dimensions: 14.37" W x 5.74" H x 10.43" D (365mm W x 146mm H x 265mm D)

Weight: 6.74 lbs / 3.06 kg

Power

AC/DC Adapter: Input: 100-240V, 50/60Hz, 0.5 A; Output: 5V 1.2A

Consumption: 6W

Turntable

Type: Belt-Drive

Drive Motor: DC motor

Speeds: 33 1/3, 45, 78 RPM

Bluetooth

Version: 5.4

Supported Profiles: A2DP, AVRCP

Operating Distance: 10 Meters (33 ft.)

Included

• Turntable
• Instruction manual
• Power adapter
• 45 RPM adapter

Please note: Design and specifications are subject to change without notice due to continual improvements.

Bluetooth is a registered trademark of Bluetooth SIG, Inc. Other trademarks and trade names belong to their respective owners.

Made in China.

This product has been manufactured and sold under the responsibility of Innovative Technology Electronics, LLC. Victrola is a trademark used under license by Innovative Technology Electronics, LLC.

Safety Warnings

1. Read all safety and operating instructions before operating the product.
2. Keep these instructions for future reference.
3. Heed all warnings on the appliance and in the operating instructions.
4. Follow all operating and use instructions.
5. Do not use this apparatus near water or moisture (e.g., wet basement, swimming pool).
6. Clean only with a dry cloth.
7. Do not block ventilation openings. Maintain at least 5 cm clearance around the apparatus. Install according to manufacturer's instructions.
8. Do not install near heat sources like radiators, heat registers, stoves, or other heat-producing apparatus.
9. Protect the power cord from being walked on or pinched, especially at plugs and where it exits the apparatus.
10. Only use attachments/accessories specified by the manufacturer.
11. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. Use caution when moving the cart/apparatus combination to avoid tip-over injury.
12. Unplug the apparatus during lightning storms or when unused for long periods.
13. Refer all servicing to qualified personnel. Servicing is required if the apparatus is damaged (e.g., power cord, liquid spilled, objects fallen in, exposed to rain/moisture, not operating normally, dropped).
14. Keep the unit in a well-ventilated environment.
15. Only use attachments/accessories specified or provided by the manufacturer.
16. To reduce the risk of fire or electric shock, do not expose the apparatus to rain or moisture. Do not place liquid-filled objects (like vases) on the apparatus.
17. The main plug serves as the disconnect device; it must remain readily operable.
18. This product is for Household Use Only, not for commercial use.
19. Symbol Description: A lightning bolt within an equilateral triangle alerts the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be sufficient to constitute a risk of electric shock.
20. Symbol Description: An exclamation mark within an equilateral triangle alerts the user to important operating and maintenance instructions in the accompanying literature.

Warning: To reduce the risk of fire or electrical shock, do not expose the apparatus to rain or moisture. No naked flame sources, such as candles, shall be placed on top of the apparatus.

Caution: Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this device. Usage of controls or adjustments other than those specified herein may result in hazardous exposure.

Caution Box Description: "RISK OF ELECTRIC SHOCK. DO NOT OPEN." and "CAUTION: TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PROFESSIONAL."

FCC & IC Warnings

FCC Statements

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules and Innovation, Science and Economic Development Canada's license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment causes harmful interference to radio or television reception, try to correct it by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC & IC Radiation Exposure Statement

This equipment complies with FCC and Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Limited Warranty

Victrola is a registered trademark of Innovative Technology Electronics, LLC.

United States

For detailed information about warranty policy and limitations, visit victrola.com/pages/warranty.

Outside the U.S., Canada, and US Territories

The warranty on this product complies with applicable law when sold to a consumer outside the United States, Canada, and US Territories. To obtain warranty service, contact the dealer or distributor from which you purchased the product, with your original receipt.

Canada and US Territories

The warranty on this product complies with applicable law when sold to a consumer in Canada or a US Territory. To obtain warranty service, contact the dealer or distributor from which you purchased the product, with your original receipt.

If assistance from the dealer is not possible, contact customer service for warranty assistance at victrola.com/contact.

Customer Support

VICTROLA.COM/PAGES/CUSTOMER-CARE

Email: support@victrola.com

Phone: (877)483-2497