NYXI Wizard 2 Bluetooth Controller

Package Contents

• NJ10 Left Controller ×1
• NJ10 Right Controller ×1
• NJ10 Middle Bridge ×1
• Multi-function Receiver ×1
• USB-C Charging Cable ×1
• Receiver Extension Cable ×1

Diagram: A visual representation of the controller, its components, and accessories.

Technical Parameters

Connectivity: Bluetooth 5.0, 2.4G Wireless

Battery Capacity: 400mAh (per controller)

Charging: 5V/0.4A via USB-C

Materials: PC + ABS + Metal + Silicone

Weight: 225g

Size: 106*155*65.5mm

Specification Diagram

Diagram: Detailed illustration of the controller with labels for all buttons and ports, including LED Channel Light, - Button, + Button, Home Button, Screen Button, TMR Hall Joystick, Mechanical D-PAD, Setting Button, Type-C Charging port, Lock Button, ZR/ZL Linear Hall Trigger, MR Button, ML Button, Left/Right Trigger Locks, SL Button, SR Button, and Reset button.

Connecting to Nintendo Switch

1. Slide the controller downward along the rails on both sides of the console screen until it clicks. The "Controllers" interface on the console will display connected left/right controllers. Diagram: Shows controller sliding onto the Switch console.
2. To remove the controller, press the release button on the back of the controller and slide it upward. Diagram: Shows pressing the release button and sliding the controller off.
3. When the console is powered on, detaching the controller from the rails will automatically establish a Bluetooth connection with the Switch. Diagram: Shows detached controllers connecting via Bluetooth to the Switch.
4. When the console is powered off, detach the controller from the rails and press the Home Button to power on and reconnect. Diagram: Shows pressing the Home button to reconnect.
5. After successfully connecting to Switch, the controller vibrates for 1 second.

Receiver Connection to PC (XINPUT Mode)

1. Press and hold the Home Button for 3 seconds to power on. LEDs 1-4 on both controllers will flash green sequentially.
2. Insert the receiver into the PC and press and hold its button until the LED blinks rapidly. Diagram: Shows receiver plugged into PC and its button being pressed.
3. Wait for pairing. Diagram: Shows LEDs flashing green sequentially, indicating pairing.

Receiver Connection to PC (DINPUT Mode)

1. In Xinput mode, press and hold A + B + Home to switch to Dinput mode. LEDs 1-4 will blink green three times.
2. Repeat the same key combination to switch back to Xinput mode. Diagram: Shows button combinations for switching between Xinput and Dinput modes.

Receiver Connection to PC/NGC

Press and hold the home button of the right handle for 5 seconds to turn on the device, and the LED1-4 of the right handle will flash green. Plug the receiver into the computer, and press and hold the button on the receiver until the LED flashes quickly. Wait for the right handle and receiver to pair successfully, and the LED lights of the receiver and the handle will be on. Diagram: Illustrates the pairing process with NGC and PC.

Receiver Connected to Wii

Turn on the Wii console, enter the game, and connect the original controller. After entering the game, unplug the original adapter, and then plug the NJ10 receiver into the console, and press and hold the button on the receiver until the LED flashes quickly. Press and hold the home button of the right handle for 5 seconds to turn on the device, and the LED1-4 of the right handle will flash green. Wait for the right handle and receiver to pair successfully, and the LED lights of the receiver and the handle will be on. Diagram: Shows connecting the receiver to the Wii console and pairing process.

Press and hold the button on the receiver again until the LED flashes quickly, and press and hold the screen button on the left handle for 5 seconds until the LED1-4 of the left handle flashes green. Wait for the left handle and receiver to pair successfully before it can be used normally. Diagram: Shows pairing the left controller.

Joystick Calibration

1. Press SL + SR + + Button (left controller: - Button) to enter calibration mode. Rotate the joysticks and press the same keys again to exit. A 1-second vibration confirms completion. Diagram: Shows the button combination and joystick rotation for calibration.
2. Switch System Calibration: Navigate to Settings > Controllers & Sensors > Calibrate Control Sticks and follow on-screen instructions.

Trigger Calibration

Press SL + SR + Home (left controller: Capture Button) to enter calibration mode. Press triggers fully to calibrate. Exit using the same keys (1-second vibration confirms completion). Diagram: Shows the button combination and trigger press for calibration.

6-Axis Gyroscope Calibration

1. On Switch: Navigate to Settings > Controllers & Sensors > Calibrate Motion Controls.
2. Place the controller on a flat surface and follow on-screen prompts. Press - and + Buttons to complete calibration.

Turbo Function

1. Supported Buttons: D-pad, A, B, X, Y, L, R, ZL, ZR.
2. Enable Turbo: Hold the Setting Button, press a target button, then release. LED4 glows white.
3. Adjust Speed: Default is 12Hz (adjustable via app).
4. Disable Turbo: Press the Setting Button + target button three times (LED4 turns off).

Button Programming

* Back Buttons (M1/M2): Can be mapped to other buttons or macros (max 21 actions per macro).

1. Mapping: Hold Setting Button + target back button for 3 seconds. Press the desired button/macro sequence, then press the back button again to save. Diagram: Shows the process of mapping back buttons.
2. Clear Mapping: Hold Setting Button + back button for 3 seconds, then press the back button without input. Diagram: Shows the process of clearing back button mapping.