AstroAI 10L Mini Fridge

Safety Information

• Please connect the appliance to a 110V power supply. (Different countries have different voltages. Please select the product that matches your actual situation when purchasing.)
• Do not connect the refrigerator to the 12V vehicle power for a long time when the engine is not running.
• Do not connect directly to the 24V cigarette lighter socket of heavy vehicles.
• Disconnect the appliance from the power supply during a thunderstorm or when it is not used for a long time to avoid damage to the appliance.
• Do not open or remove the cover, as you may be exposed to dangerous voltages or other hazards.
• To avoid the risk of fire or electric shock, avoid overloading sockets, extension cords, or other appliances that carry electrical loads.
• Use a suitable power source. Plug the product into a suitable power source according to the instructions in the manual or the marking on the product.
• The supply voltage should match the voltage indicated in the manual and on the nameplate of the appliance.
• To completely disconnect the appliance from the power supply, turn off the power and unplug the power cord completely from the outlet.
• Do not bend, stretch, or pull the power cord to avoid electric shock.
• The socket outlet must be easily accessible during installation.
• Do not use it where dust or other air pollutants can be sucked into the fan.
• Leave a gap of at least 5 cm from the back and sides of the appliance to allow for air circulation and heat dissipation.
• Do not place the refrigerator in poorly ventilated areas, such as the trunk of a car.
• Handle with care, do not squeeze.
• Do not sit on the refrigerator.
• Turn off the refrigerator for 30 minutes before switching from heating mode to cooling mode to allow it to return to room temperature, and vice versa.
• Do not expose the product to rain and keep it away from corrosive gases and liquids.
• If it is not applicable for a long time, please disconnect the power supply and store it in a dry and ventilated environment. Avoid direct sunlight.
• Strict use by children alone; children should be used under adult supervision.

Size Description

The dimensions of the AstroAI 10L Mini Fridge are:

• Height: 32.5 cm (12.8 in)
• Width: 19 cm (7.5 in)
• Depth: 27 cm (10.6 in)
• Internal dimensions are approximately: Height 25 cm (9.8 in), Width 18 cm (7.1 in), Depth 25 cm (9.8 in) - *Note: Internal dimensions are approximate and may vary slightly.*

Illustrated Parts

The mini-fridge has the following parts:

• (1) Handle
• (2) Door Latch
• (3) Shelf
• (4) Partition
• (5) Condensate Pan
• (6) Heating Mode Indicator
• (7) Cooling Mode Indicator
• (8) Heat / Off / Cool Switch
• (9) Non-ECO Mode / ECO Mode Switch
• (10) DC Power Socket
• (11) AC Power Socket
• (12) DC Power Cord
• (13) AC Power Cord

Instructions

Car Operation Steps

1. Before plugging in the power cord, turn the mode switch to the Off position (middle gear of the Heat/Off/Cool switch). At this time, neither indicator light will be on.
2. Plug the power cord into the DC power socket on the back of the refrigerator.
3. Secure the refrigerator and plug the power cord into the car's power outlet.
4. Turn the Cool/Heat switch to Cool or Heat. The green indicator light will illuminate when the cooling mode is activated. The red indicator light will illuminate when the heating mode is activated.

WARNING: Operating the portable refrigerator with the vehicle turned off may drain the vehicle's battery.

Home Operation Steps

1. Before plugging in the power cord, turn the mode switch to the Off position (middle gear of the Heat/Off/Cool switch). At this time, neither indicator light will be on.
2. Plug the power cord into the AC power socket on the back of the refrigerator.
3. Secure the refrigerator and plug the power cord into a standard wall outlet.
4. Turn the Cool/Heat switch to Cool or Heat. The green indicator light will illuminate when the cooling mode is activated. The red indicator light will illuminate when the heating mode is activated.

Mode Tips

ECO Mode

• ECO mode is an energy-saving mode. The minimum cooling temperature in this mode is higher than in non-ECO mode, the cooling rate is slower, and the noise is much lower.
• The refrigerator defaults to a mode. If you find it too noisy, you can switch from non-ECO mode to ECO mode. If you find the cooling insufficient, you can switch from ECO mode to non-ECO mode.

Cooling Mode Tips

• For the fastest cooling rate, fill the refrigerator with chilled beverages.
• The cooling effect is influenced by the ambient temperature. A high ambient temperature can cause the minimum temperature the refrigerator can reach to rise. Note: Ambient temperature refers to the temperature of the surrounding air. For example, if the unit is used for cooling and the ambient temperature around you is 24°C, the unit will maintain the temperature within your set error of approximately 1.7°C to 4.4°C.

Thermal Mode Tips

• The refrigerator is designed to maintain the temperature of items. It is not intended for heating items.
• As long as the door is properly closed, hot items will remain warm for several hours after the refrigerator is closed.

Care and Maintenance

• Unplug the unit completely before routine maintenance.
• Use a damp cloth and a mild detergent to clean the housing.
• When not in use, ensure the interior is completely dry before storing.

Troubleshooting

Parameter Description

3-Year Limited Warranty from AstroAI

Every AstroAI 10L Mini Fridge is free from defects in material and workmanship. This warranty does not cover damage caused by neglect, misuse, contamination, alteration, accident, or abnormal operating or handling conditions. This warranty is valid only for the original purchaser and is non-transferable.

AstroAI always aims to provide customers with excellent products and customer service. To learn more about AstroAI, please visit astroai.com.