Flexispot F7D Installation Guide

Package Contents

(A) Parts Included

• ① Bottom support: 1 PC
• ② Screw: 1 PC
• ③ Washer: 1 PC
• ④ Butterfly knob: 1 PC
• ⑤ Bottom support 2: 1 PC
• ⑥ Knob: 1 PC
• ⑦ Cable cover: 1 PC
• ⑧ Nylon ties: 10 PCS
• ⑨ Anti-slip rubber 1: 1 PC
• ⑩ Anti-slip rubber 2: 4 PCS
• ⑪ Anti-slip rubber 3: 1 PC
• ⑫ Cable cover 2: 2 PCS
• ⑬ M6 box wrench: 1 PC

(B) Screw Set and Tools

(C) Tools Needed for Assembly

[Tool icon representing wrenches and hex keys]

Installation Steps

STEP 1: Preparations before installing monitor

1. Verify that the monitor has VESA spacings of either 100 x 100 mm or 75 x 75 mm. If not, the monitor cannot be installed.
2. Remove the monitor's original fixed base. Be careful not to scratch the screen.

[Diagram showing VESA hole spacing options: 75 x 75 mm and 100 x 100 mm]

STEP 2: Install bracket on desk

Option A: Using Desk Clamp

This option is for desks without a grommet hole.

1. Attach the bottom support 2 (part 5) to the desk clamp mechanism by tightening screws (C) with the 4 x 4mm hex key (F).
2. Turn the mount upside-down and place the anti-slip rubber 1 (part 9) onto the bottom support 2 (part 5).
3. Place anti-slip rubber 2 (part 10) onto the top of the clamp knob (part 6).
4. Attach the clamp knob (part 6) to the bottom support 2 (part 5) using screws (D) with the 4 x 4mm hex key (F).
5. Position the bottom clamp against the desk surface and fully tighten the clamp knob (part 6).
6. Place the cable cover (part 7).

[Diagram illustrating clamp installation: bottom support 2 (5) attached to clamp, anti-slip rubbers (9, 10) placed, knob (6) tightened against a desk surface. A note indicates desk thickness range: 0.79" - 4.72" (20-120mm), select appropriate hole in the bottom support according to desk thickness.]

Option B: Using Grommet Hole

This option is for desks with a grommet hole.

1. Insert screw (part 2) into the hole of the bottom support 1 (part 1).
2. Attach the bottom support 1 (part 1) to the base by tightening screws (C) with the 4 x 4mm hex key (F). Keep the screw side pointing down.
3. Turn the mount upside-down and place anti-slip rubber 1 (part 9) onto the bottom support 1 (part 1).
4. Insert the bottom support assembly into the desk grommet hole.
5. Attach anti-slip rubber (part 11) onto the washer (part 3).

[Diagram illustrating grommet installation: screw (2) inserted into bottom support 1 (1), support attached to base with screws (C) and hex key (F). Anti-slip rubber 1 (9) placed on support. Assembly inserted into desk hole. Anti-slip rubber (11) attached to washer (3). A note indicates desk thickness range: 0.79" - 3.94" (20-100mm) and hole size: 0.3" - 2.8" (8.5 - 70mm).]

STEP 3: Attach the monitor to the plate

1. Add washers (E) to appropriate screws (A or B), depending on monitor hole size.
2. Attach the monitor to the arm using screws (A or B). For 100mm x 100mm VESA holes, first attach the top screws to the monitor and then set the monitor into the top grooves of the monitor plate (part 2).
3. Then add the bottom screws through the monitor plate and securely tighten all four screws. For 75mm x 75mm VESA holes, attach all four screws through the monitor plate and tighten securely.

[Diagram showing adding washers (E) to screws (A, B). Diagram showing monitor attachment to the arm plate using screws (A, B, G). Diagram illustrating swivel function adjustment using 5x5 hex key (G) with angle indicators: ±90°, ±180°. Diagram illustrating tilt function adjustment using M6 box wrench (13) with angle indicators: -85° to +15°.]

Monitor Height Adjustment: After installing the monitor, adjust its height. If the monitor cannot stop at any height, use the supplied 5x5 hex key (G) to adjust the screw on the arm. To make the mount and monitor's weight equal and allow it to stop at any height, adjust the screw in the "-" direction when the monitor is up and the "+" direction when it is down.

STEP 4: Using cable management

1. Manage the cables with nylon ties (part 8).
2. Take off the cable cover (part 7) and slide cables through the underside of the arm, then tighten the cover with a screw.
3. Pass the cable along the slot and place the cable cover 2 (part 12).

[Diagram showing cable management: nylon ties (8) bundling cables. Textual description for securing cables: "Take off the cord and put the cable in, then use screw to lock the cord." Textual description for attaching cover: "Insert the bottom part, then lock the bayonet." Cable cover (12) is shown.]

Important Safety Information & Cautions

⚠️ This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children.

• Make sure these instructions are read and completely understood before attempting installation. If you are unsure of any part of this installation, please contact a professional installer for assistance.
• The desk or mounting surface must be capable of supporting the combined weight of the mount and the monitor; otherwise, the structure must be reinforced.
• Proper tools must be used. A minimum of two people are recommended for this installation. Failure to install properly can result in property damage.
• Check joint parts every two months, making sure the screws have not loosened.

This product was designed to be installed on a desk. Before installing, ensure the mount will support the combined load of the equipment and hardware. Never exceed the maximum load capacity of 11 lbs (5 kg), or else it may result in product failure.

Note: This product is intended for indoor use only. Use of this product outdoors could lead to product failure.