DOSS SoundBox XL Bluetooth Home Speaker User Manual
Brand: DOSS
Introduction
Thank you for purchasing DOSS SoundBox XL with Bluetooth function. We encourage you to read this instruction guide thoroughly to get the most out of this innovative home speaker.
Package Content
- Home speaker x 1
- Power adapter with power plug x 1
- 3.5mm audio cable x 1
- User manual x 1
Product Overview
The DOSS SoundBox XL features several controls and ports:
- 1. Power button: Long press to turn the device ON/OFF.
- 2. Mode switch: Press the 'M' button to switch modes.
- 3. LED lights (1-4): Indicate Bluetooth mode, AUX in mode, TF card mode, and battery status.
- 4. Volume control: Use '-' to decrease volume and '+' to increase volume.
- 5. Track Back button: Press to go to the previous track.
- 6. Play/Pause button: Press to stop playback and press again to resume.
- 7. Track Forward button: Press to go to the next track.
- 8. Power port: DC 12V 2.5A input for charging.
- 9. LED charging light: Steady red indicates charging; light off indicates fully charged.
- 10. AUX in: Connect compatible devices using a cable for playback.
- 11. TF card slot: For TF card playback. Supports MP3, WAV, WMV formats. Recommended to use cards formatted to FAT32, 32GB or smaller.
Visual Description of Controls: The speaker has a rectangular form factor. On the top panel, from left to right, are the power button, mode switch, volume down, play/pause, volume up, track back, and track forward buttons. The front panel features LED indicators. The rear panel has the power port, AUX in port, and TF card slot.
Status Indicators
The LED lights provide status information:
- Indicator 1 (Blue): Flashing blue means the speaker is in pairing mode; Steady blue means the device is successfully paired.
- Indicator 2 (Red): Steady red indicates the mode has switched to AUX in successfully.
- Indicator 3 (White): Steady white indicates the mode has switched to TF card successfully.
- Indicator 4 (Red): Flashing red indicates low battery power.
Charging Indicator: Steady red light means the battery is charging. The light turns off when the battery is fully charged.
Preparation
- Connect the supplied DC 12V 2.5A power adapter to the charging port on the back of the speaker. Ensure the power supply is within the 100V-240V standard.
- Ensure the speaker is fully charged before first use. Charging takes approximately 2-3 hours.
- The LED charging light glows red while charging and turns off when fully charged.
- To turn the speaker ON or OFF, press and hold the power button for 2 seconds.
Pairing the Wireless Speaker with Your Smart Device
- Place your smart device and speaker no more than one meter apart.
- Turn on the speaker by pressing the power button for 2 seconds. A tone will be heard, and the blue LED will flash, indicating pairing mode.
- Set your smart device to "discover" Bluetooth devices.
- Enable Bluetooth on your device and select "DOSS SoundBox XL" from the list of available devices.
- If pairing is successful, the LED will turn solid blue, and your device will confirm the connection. If pairing fails after 60 seconds, repeat the process.
Troubleshooting
| Problem | Solution |
|---|---|
| Cannot play music after pairing | Please select 'DOSS SoundBox XL' as the default playback device on your smart device. |
| Cannot Pair with Bluetooth devices | Press the Play/Pause button for 5 seconds to reset, then try pairing again. |
| Bluetooth cuts off during playback | This may be caused by charging interference. Try placing the speaker in a different location and avoid charging it during playback. |
| Laptop prompts to install driver | Ensure your device has Bluetooth enabled and check its settings. |
| Not pair with transmitter | Contact your device manufacturer for assistance. |
| The speaker does not play when the card is inserted, and jumps directly back to Bluetooth mode | Check if the TF card format is FAT or FAT32. If not, format it to FAT or FAT32. Also, check the song format; the speaker only supports MP3, WAV, WMV. There might be a problem with the song's format; try deleting songs of the same problematic format. |
| The song cuts off during playback | There may be an issue with the song's format. Try a different song. |
| Cannot turn off the speaker | Use a needle or thin wire to poke the reset button located inside the AUX-in port. |
Product Specifications
| Category | Details |
|---|---|
| Product Type | Home speaker |
| Unit Dimension | 11.8 x 2.64 x 5.2 inches |
| Unit Weight | 3.46 lbs |
| Output Power | 2 x 10 W | 12 W Subwoofer |
| Driver Unit | 2.0 inch speaker x2 + 1.5 inch x 3.5 inch passive radiator x2 |
| Frequency Response | 40Hz - 20kHz |
| Signal to Noise Ratio | ≥70db |
| Warranty | One-year limited |
| Power - Battery Type | Li-ion 7.4V, 2200mAh |
| Power - Power Adapter (supplied) | Model: DYS624-120250W-1/K Input: 100-240 V, 50/60 Hz, 0.8A MAX Output: 12 V, 2500 mAh |
| Wireless/Networking - Bluetooth Specification | 4.0+EDR |
| Wireless/Networking - Supported Bluetooth Profiles | A2DP, AVRCP, SPP |
| Wireless/Networking - Maximum Operation Range | 10 meters / 33ft |
Warnings
- Do NOT drop, hit, or shake the device.
- Do NOT disassemble, repair, or modify the speaker by yourself.
- Do NOT use cleaning products that contain benzene, solvents, or alcohol.
- Do NOT expose the speaker to excessive heat or direct sunlight for a long time.
- Do NOT store the device in a place with humidity or dust.
- Do NOT place heavy objects on top of the speaker.
- Do NOT use the speaker near a microwave oven or wireless LAN products.
