DOSS SoundBox Portable Bluetooth Speaker

Packing Content

• DOSS SoundBox Wireless Speaker
• USB Type-C Charging Cable
• User Manual

Product Overview

The DOSS SoundBox is a portable wireless speaker with various controls and ports.

Top View:

• [Mode Button]: Touch to switch between Bluetooth, TF card, and Aux-in modes.
• [Skip Backward Button]: In Bluetooth or TF card mode, touch to skip backward.
• [Play/Pause/Call Button]: In Bluetooth mode, touch to answer/end a call (hold 3s to reject). Speak into the built-in microphone. Touch to play/pause music (hold 5s to disconnect Bluetooth). In TF card mode, touch to play/pause music.
• [Skip Forward Button]: In Bluetooth or TF card mode, touch to skip forward.
• [Volume Control Dial]: Rotate clockwise to increase volume, counterclockwise to decrease.

Side/Rear View:

• [Power Button]: Long press to turn on/off.
• [Line In Port]: Connect via 3.5mm auxiliary cable (not included). Audio playback controlled by the connected device.
• [TF Card Slot]: Play music from a TF card (MP3, WMA, FLAC, max 32GB, FAT32/FAT format).
• [Type-C Port]: For charging the speaker.
• [Charging Indicator Light]: Indicates charging status.

Indicators

Pairing DOSS SoundBox with Your Device

1. Place the speaker and your device within one meter.
2. Turn on the speaker. The top center indicator flashes blue.
3. Turn on Bluetooth on your device and select "DOSS SoundBox" from the list.
4. Once paired, a prompt tone will sound, and the top center indicator will turn steady blue. If pairing fails, repeat steps 1-3.
5. To disconnect, press and hold the [Play/Pause/Call Button] for 5 seconds.

Connecting DOSS SoundBox to Echo Dot

You can connect the speaker to an Echo Dot via Bluetooth or auxiliary cable.

1. Download the Alexa app and connect your Echo Dot to your Wi-Fi network.
2. Ensure the DOSS SoundBox is in pairing status (press and hold the [Play/Pause/Call Button] for 5 seconds if already paired).
3. Open the Alexa app, tap MENU, then tap SETTINGS.
4. Tap your Echo Dot in the Alexa app, then tap BLUETOOTH.
5. Select "DOSS SoundBox" from the Bluetooth list. If it doesn't appear, press and hold the [Play/Pause/Call Button] for 5 seconds and try reconnecting.

Specifications

• Output Power: 6W x 2
• Driver Unit: 1.5 inch driver x 2 + 2.6 inch passive radiator
• Frequency Response: 100Hz-18kHz
• Signal to Noise Ratio: >=55dB
• Unit Weight: 560 g
• Unit Dimension: 6.6 x 2.7 x 2.9 inches (16.76 x 6.86 x 7.37 cm)
• Bluetooth Range: 10 meters / 33ft
• Warranty: One-year limited

Battery

• Type: Li-ion 3.7V 2200mAh
• Input: 5V =1A
• Charging Time: 3 hours
• Playback Time: Up to 20 hours (at 50% volume)

Battery Notes:

• Fully charge the speaker before initial use.
• If the speaker beeps every few seconds, please recharge it for 2-3 hours.
• The speaker has a battery saver mode that auto-powers off after 15 minutes of inactivity. To disable this feature, contact support.

Support

For any further assistance, please contact the support team at support@dossav.com.

Warnings

• DO NOT drop, hit, or shake the speaker.
• DO NOT disassemble, repair, or modify the speaker yourself.
• DO NOT use cleaning products containing benzene, solvents, or alcohol.
• DO NOT expose the speaker to excessive heat or direct sunlight for prolonged periods.
• DO NOT store the speaker in places with high humidity or dust.
• DO NOT place heavy objects on top of the speaker.
• DO NOT use the speaker near microwave ovens or wireless LAN products.

Regulatory Information

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

ISED Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

CAN ICES-3(B)/NMB-3(B)

L'appareil a été évalué pour répondre aux exigences générales d'exposition aux RF. Le dispositif peut être utilisé sans restriction dans des conditions portatives d'exposition. Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps.