ACT Monitor Desk Mount for 2 Monitors

Important Safety Information

CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.

• Mounts must be attached as specified in assembly instructions. Improper installation may result in damage or serious personal injury.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
• This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and injury.

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to the installation.

MAINTENANCE: Check that the bracket is secure and safe to use at regular intervals (at least every three months).

Parts List

Components:

• A: Monitor Arm (x2)
• B: Desk Clamp (x1)
• C: Pole (x1)
• D: Pole Clamp (x1)
• E: Base Plate (x1)
• F: Monitor Mounting Plate (x2)
• G: Cable Management Clip (x1)
• H: M6x10 Screws (x5)
• I: M6x16 Screws (x2)
• J: M6x16 Screws (x3)
• K: Through-Hole Mount Base (x1)
• L: Washer (x2)
• M: M3x8 Screws (x2)
• N: M4x12 Screws (x2)
• O: M5x12 Screws (x2)
• P: M5x12 Screws (x4)
• Q: Allen Key (4mm) (x1)
• R: Allen Key (6mm) (x1)

Hardware Sets:

• M-A: M4x12 Screws (x4)
• M-B: M5x12 Screws (x4)
• M-C: D5 Screws (x4)

Assembly Instructions

Step 1: Attach Pole to Clamp

Secure the pole (C) to the desk clamp (B) or through-hole mount base (K). Ensure the cable hole on the pole is not visible from the front when attaching to the clamp.

Step 2: Mount to Desk

Option A (Desk Clamp): Attach the pole (C) to the desk clamp (B). The clamp is suitable for desks with a thickness of 10-55mm.

Option B (Through-Hole Mount): If your desk has a through-hole (Ø10-60mm), use the through-hole mount base (K) with the pole (C). The through-hole diameter should be approximately 10mm (3/8 inch).

Step 3: Secure Pole Assembly

Attach the pole (C) to the desk clamp (B) using the provided screws (e.g., M-A, M-B). Ensure the pole is vertical and stable.

Step 4: Attach Monitor Arms

Slide the monitor mounting plates (F) onto the pole (C). Secure them using the provided screws (e.g., H, I, J). Adjust the height as needed.

Step 5: Mount Monitors

Attach the monitors to the monitor mounting plates (F) using the appropriate screws (e.g., M-A, M-B, M-C) provided with the mount, ensuring they match your monitor's VESA pattern.

Step 6: Adjust Monitor Position

Adjust the tilt (±90 degrees) and swivel (±90 degrees) of the monitor arms. The arms have adjustable ranges, for example, 52mm, 181mm, 147mm, and 76mm for tilt/swivel adjustments.

CAUTION: DO NOT use the display beyond the indicated arrow range to avoid tipping.

Step 7: Fine-Tuning

If a monitor does not stay in the desired position, tighten the adjustment screws as shown in the diagram (refer to the 'Too long / Too Short' illustration).

Dimensions and Adjustments

The monitor arms offer various adjustment capabilities:

• Vertical pole height: 100mm, 114mm
• Horizontal arm reach: 52mm, 181mm, 147mm, 76mm
• Tilt adjustment: ±90 degrees
• Swivel adjustment: ±90 degrees
• Rotation adjustment: ±180 degrees
• Pole diameter: Ø48mm
• Desk clamp thickness range: 10-55mm
• Through-hole diameter range: Ø10-60mm
• Desk thickness for through-hole mount: 10-75mm

Support and Warranty

For service, manuals, firmware, or updates, please visit: www.act-connectivity.com

For safety information, please visit: www.act-connectivity.com/safety

ACT, Koolhovenstraat 1E, 3772 MT Barneveld, The Netherlands

Warranty: 5 Year Warranty

Made in China