ACT AC8305 Monitor Desk Mount with Laptop Arm

Introduction

This document provides instructions for the installation and assembly of the ACT AC8305 Monitor Desk Mount with Laptop Arm. Please read all instructions carefully before beginning.

Safety Warnings and Precautions

• Read Entire Instruction: Please read the entire instruction before you start the installation and assembly.
• Weight Limits: Use with products heavier than the rated weights indicated may result in instability causing possible injury. Ensure the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
• Proper Attachment: Mounts must be attached as specified in assembly instructions. Improper installation may result in damage or serious personal injury.
• Hardware: Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
• Small Parts: This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
• Indoor Use Only: This product is intended for indoor use only. Using this product outdoors could lead to product failure and injury.
• Component Check: IMPORTANT: Ensure that you have received all parts according to the component checklist prior to the installation.

Maintenance

Check that the bracket is secure and safe to use at regular intervals (at least every three months).

Parts List

Verify you have all the following components:

Main Components:

• Part A (x2)
• Part B (x2)
• Part C (x1)
• Part D (x2)
• Part E (x2)
• Part F (x1)
• Part G (x1)
• Part H (x1)
• Part I (x1)
• Part J (x1)
• Part K (x1)
• Part L (x4)
• Part M (x2)

Hardware:

• M4x12 screws (x4) - labeled M-A
• M4x16 screws (x4) - labeled M-B
• M5x12 screws (x4) - labeled M-C
• M5x16 screws (x4) - labeled M-D
• D5 screws (x4) - labeled M-E
• M-F screws (x4)

Tools:

• 4mm tool (x1) - labeled P
• 6mm tool (x1) - labeled Q

Assembly Instructions

Follow these steps carefully:

1. Step 11a: Attach part G to part F using four M-A screws.
2. Step 2a: Connect part F (with attached part G) to parts N and O using four M-C screws. (Note: Parts N and O are not explicitly listed in the main parts list but appear in diagrams. Assuming they are part of the desk clamp mechanism).
3. Step 2b: Attach part J to part K.
4. Step 3: Attach part I to part B using four M-E screws.
5. Step 4a: Attach part A to part M using four M-C screws.
6. Step 4b: Attach part M (with attached part A) to part H using four M-D screws.
7. Step 5: Attach part E to part D using four M-F screws.
8. Step 6: Attach part Q (6mm tool) to part M.
9. Step 7: Attach part C to part E.
10. Step 8: Attach part L to part A.
11. Step 9: Attach part B (with attached part I) to part H.
12. Step 10: Attach part J (with attached part K) to part M.
13. Step 11: Attach part L to part A. (This step appears to be a repeat or a detail of step 8, ensuring L is secured to A).
14. Step 12: Attach part M to part Q.
15. Step 13: Final adjustments and checks. The mount supports articulation up to 180° rotation, 360° swivel, and ±45° tilt. Ensure compatibility with your monitor/laptop dimensions and weight.

Note: The diagrams indicate various dimensions for monitor/laptop compatibility, such as screen sizes ranging from 10-88mm, arm reach adjustments, and mounting plate dimensions (e.g., 443mm, 280mm, 105mm, min10mm-max88mm, 75mm, 100mm, 114mm, 38mm, 185mm, 36mm, 140mm, min240mm-max420mm, 300mm). These should be considered during installation to ensure proper fit and stability.

Company Information and Support

Manufacturer: ACT

Address: Koolhovenstraat 1E, 3772 MT Barneveld, The Netherlands

For safety information, please visit: www.act-connectivity.com/safety

For service, manuals, firmware, or updates, please visit: www.act-connectivity.com

This product is Made in China.

This product comes with a 5 Year Warranty.