Important Notes & Warnings
Before proceeding with the installation, please ensure your hardware and cooling system are functioning correctly, including tightness, pump function, and fans. This minimizes troubleshooting effort. Alphacool does not assume warranty for the manufacturer of electronic components. Assembly of the cooling system is at your own risk.
- Do not overtighten screws. Overtightening can loosen mounting bolts, preventing uniform cooler contact.
- Avoid using tools like wrenches for fastening connections. Connectors with 8mm thread length may restrict flow.
- Perform a leak test before assembling/installing the cooler. The water pressure in the loop should not exceed 0.8 Bar.
- Ensure the cooler makes contact with all components to be cooled using thermal grease and thermal pads. The correct imprint on the GPU indicates proper contact.
Safety Advice: Not suitable for children under 6 years (contains small, swallowable parts). Never operate cooling components without ensuring coolant flows through the system. Coolers without coolant flow can overheat, posing a burn hazard, and can damage computer hardware. Always verify the pump is functioning when the hardware is powered on.
When tightening connectors, do not use tools like wrenches or pliers. Plastic or metal threaded connections linked with plastic parts can be easily overloaded, leading to cracks or damage. Such damage, or damage from leaking coolant, is not covered by warranty. Use only connectors with a sealing ring; hand-tightening is sufficient. Tools are only permitted when explicitly indicated in the instructions.
Intended Use: Alphacool International GmbH cooling components are approved for cooling Alphacool International GmbH computer components. Warranty is void for non-intended use.
Screw Set and Components
The following components are included in the screw set:
| Quantity | Description | Specification |
|---|---|---|
| 8x | Screws | M3x12 |
| 2x | Screws | M3x8 |
| 2x | Screws | SW2 & SW2,5 |
| 8x | Thermal Pad | 15mm x 15mm x 1.5mm |
| 1x | Thermal Pad | 30mm x 30mm x 1.5mm |
| 9x | Thermal Pad | 15mm x 15mm x 3mm |
| 1x | Thermal Pad | 30mm x 30mm x 3mm |
Installation Steps
Step 1: Preparation and Disassembly
Place the hardware on an antistatic mat. Begin by dismantling the original cooler. Depending on the cooler's design, you may need to remove fan screws and unhook the fan connector. Exercise extreme caution if the original cooler is attached with thermal glue, as components can be easily torn off. Carefully collect all removed parts. Clean the hardware of any thermal paste or pad residues using a solvent like alcohol.
Step 2: Apply Thermal Paste to GPU
Using a plastic strip or a thermal paste spreader, apply an even layer of thermal paste to the GPU. The layer should be less than one millimeter thick to prevent unnecessary contamination of surrounding components.
Step 3: Place Thermal Pads (Red)
Remove the protective film from the red thermal pads (15mm x 15mm x 1.5mm). Place these pads onto the memory chips as indicated.
Step 4: Mount the Cooler
Mount the assembled cooler onto the graphics card as shown in the diagram. If there is a protective film on the cooler's base, remove it now. Clean the contact surfaces on the cooler's base with alcohol or a similar agent to ensure they are free of contaminants.
Step 5: Apply Thermal Pads (Yellow) and Initial Screw Installation
Cut the yellow thermal pads for the backplate as shown in the diagram. Place these pads on the rear side of the voltage converters and the GPU. Remember to remove the protective film from both sides of the pads. Loosely screw in the screws with washers into the cooler; do not tighten them fully yet.
Step 6: Install Backplate
Place the backplate onto the graphics card as depicted. Apply slight pressure to ensure optimal contact between the backplate, cooler, and graphics card.
Step 7: Final Cooler Assembly
Screw the cooler together. Finger-tighten the screws with one turn each, working in a crosswise pattern. Refer to the specific instructions for correct tightening. After approximately 12 hours of using the graphics card, re-tighten all screws.
Warranty Information
Data, designs, illustrations, technical data, weight, measurement, and performance descriptions in brochures, catalogs, circulars, advertisements, or price lists are for informational purposes only. Alphacool International GmbH does not guarantee the accuracy of this information. The details in the order and order confirmation are solely decisive regarding the type and scope of delivery.
If a defect covered by warranty exists, customers are entitled to demand subsequent delivery, withdraw from the contract, or reduce the purchase price according to legal provisions. The warranty period for consumers is two years from receipt of goods. For entrepreneurs, it is one year.
Warranty claims are valid only with the original invoice, sales receipt, or an official confirmation from Alphacool International GmbH. It is at Alphacool International GmbH's discretion to repair or replace defective products or components. Replaced items become the property of Alphacool International GmbH.
Repairs by unauthorized persons will void warranty coverage unless previously agreed upon with Alphacool International GmbH. Costs arising from product retrofitting are not covered.
Warranty Exclusions:
- Regular checks, maintenance, and repair, or replacement of wear parts.
- Incorrect operation or defects caused by faulty installation.
- Damage caused by storm, water, fire, overvoltage, force majeure, war, incorrect power connection, insufficient or faulty ventilation, or other external factors.
- Damage resulting from transportation or improper packaging.
Consumer rights in their respective countries, such as claims against the seller as stipulated in the sales contract, are not affected by this warranty declaration. Alphacool International GmbH, its branches, and distributors are not liable for direct or indirect damages or losses unless mandated by compelling legal regulations.
Alphacool International GmbH does not assume the warranty of the electronic component manufacturer. Cooler assembly is performed at your own risk.
Contact Information
Alphacool International GmbH
Address: Marienberger Str. 1, D-38122 Braunschweig
Email (German/English): info@alphacool.com
Internet: www.alphacool.com
Forum: Accessible via the homepage
Support Phone: +49 (0)5 31/ 288 74-100
Fax: +49 (0)5 31/ 288 74-22
All parts of the cooling system are RoHS compliant.
Dispose of products through an authorized waste management company in your country. Disposal with household waste or similar municipal waste collection facilities is not permitted.
© Copyright 2014 Alphacool International GmbH. All rights reserved, including translation. Analog or digital reproductions of any kind, except for a consumer's own copy, require written consent from Alphacool International GmbH. This manual reflects the technical state at the time of printing. Subject to change without prior notice.
