Pure & Easy Assembly Instructions
Model: ZZJSZN-V2
Notice
Scan the QR code with your smartphone camera for additional instructions. This document provides assembly guidance in multiple languages.
Important: Retain for future reference. Read carefully.
Assemble on a flat, clean, and soft surface.
Recommendations and Safety
Professional installation is highly recommended.
Periodically check that all components are tightly secured.
Auxiliary Tools Needed:
- Drill
- Hammer
- Screwdriver
- Tape Measure
- Ladder
- Saw
- Safety Helmet
Safety Warning: Serious or fatal crushing injuries can occur from furniture tip-over. Always secure this furniture to the wall using tip-over restraints. The diagram illustrates a furniture unit tipping over, with a warning symbol, and shows how to secure it to the wall with restraints.
Assembly Tips
It is recommended that multiple people assemble this product.
Never let children climb or hang on drawers, doors, or shelves. The diagram shows children climbing on furniture with a prohibition symbol.
Drawer Runner Installation: Press and hold the drawer runner lock, then continue to slide drawer runners apart before installation. The diagram shows this action.
Using Cam Lock and QuickFit
Tighten QuickFit until the shoulder is flush with the panel. Do not overtighten or undertighten. The diagram shows correct and incorrect tightening methods.
When fitting the cam lock, ensure the starting position is correct before inserting the connecting QuickFit. The diagram illustrates the correct alignment.
The QuickFit head should be in the center of the cam lock when the two panels are joined. The cam lock should be inserted before the QuickFit. Turn the cam lock clockwise to tighten. The diagram shows the final assembled state and the turning direction.
Parts List
| Item No. | Description | Quantity |
|---|---|---|
| A | M6 X 35MM Screw | x48 |
| B | Cam Lock (Φ15 X 12MM) | x24 |
| C | Screw (Φ8 X 30MM) | x18 |
| D | Screw (Φ3.5 X 12MM) | x76 |
| E | Screw (Φ4 X 35MM) | x32 |
| F | Dowel (Φ14.5 X 4MM) | x8 |
| G | Support Rod (285MM) | x6 |
| H | Support Rod (120MM) | x6 |
| I | Bracket | x16 |
| J | Screw | x2 |
| K | Screw (Φ4 X 14MM) | x2 |
| L | Dowel | x2 |
| M | Cam Lock (Φ15 X 10MM) | x24 |
| 1 | Top/Bottom Panel | x1 |
| 2 | Side Panel | x1 |
| 3 | Side Panel | x1 |
| 4 | Shelf Panel | x1 |
| 5 | Shelf Panel | x1 |
| 6 | Shelf Panel | x1 |
| 7 | Shelf Panel | x1 |
| 8 | Shelf Panel | x1 |
| 9 | Shelf Panel | x1 |
| 10 | Shelf Panel | x1 |
| 11 | Back Panel | x4 |
| 12 | Drawer Side Panel (Left) | x3 |
| 13 | Drawer Side Panel (Right) | x3 |
| 14 | Drawer Front/Back Panel | x6 |
| 15 | Drawer Front/Back Panel | x6 |
| 16 | Drawer Bottom Panel | x6 |
| 17 | Drawer Bottom Panel | x6 |
| 18 | Corner Bracket | x3 |
Exploded View
The exploded view shows all components laid out. It illustrates how the main panels (1, 2, 3), shelves (4-10), back panels (11), and drawer components (12-17) are assembled. The base unit is formed by connecting side panels (2, 3) to the bottom panel (1), with shelves (4-10) and back panels (11) integrated. Drawer boxes are constructed separately using panels 12-17 and then installed.
Assembly Steps
Step 1: Base Panel Assembly
Attach part 1 to part 2 using six screws (A) and two connectors (F). Attach part 3 to part 1 using six screws (A) and two connectors (F). The diagram shows screws (A) and connectors (F) being used to join panels.
Step 2: Drawer Runner Attachment
Attach drawer runners (G1) to panels 2 and 3 using twelve screws (D). Separate the inner and outer parts of the drawer runners (G1, G2) by pressing the latch. The diagram shows screws (D) securing the runners and the process of separating them.
Step 3: Shelf Attachment (Part 4)
Attach part 4 to part 1 using one panel (4), nine screws (A), and two connectors (F). Rotate part 4 by 180 degrees. The diagram shows the panel being attached and rotated.
Step 4: Drawer Runner Attachment to Shelf
Attach drawer runners (G1) to part 4 using twelve screws (D). Rotate part 4 by 180 degrees. The diagram shows screws (D) securing the runners to the panel.
Step 5: Base Structure Assembly
Assemble the base structure. Attach part 5 to part 2 using one connector (F). Attach part 6 to part 5 using one connector (F). Attach part 7 to part 2 and part 6 using six cam locks (B) and one connector (F). The diagrams show the sequence of connecting these panels.
Step 6: Back Panel and Top Shelf
Insert back panel 11 into the grooves of panels 2, 6, and 7. Attach part 4 to the structure using six cam locks (B). The diagram shows the back panel sliding into place and the top panel being secured.
Step 7: Additional Shelves
Attach shelf panels 8, 9, and 10. Use one panel (8), one panel (9), and one panel (10). Secure them with three cam locks (B) and six screws (C), and one connector (F). The diagram shows the placement and fastening of these shelves.
Step 8: Rear Panel and Top Panel
Insert back panel 11 between panels 8 and 9. Attach part 3 to the top of the structure using three cam locks (B) and six screws (C). The diagram shows the back panel insertion and the top panel attachment.
Step 9: Final Back Panels
Insert back panels 11 into the grooves of panels 2, 6, 4, and 9. The diagram shows two back panels being slid into place.
Step 10: Top Panel Installation
Attach the top panel (1) to the assembled structure. Secure it using six cam locks (B) and six screws (C). The diagram shows the top panel being placed and fastened.
Step 11: Drawer Box Construction
Assemble the drawer boxes. Use panels 14, 15, 16, and 17. Secure them with six screws (E) for each drawer. The diagram shows the construction of a drawer box. Repeat for all six drawers.
Step 12: Drawer Runner Installation
Install the drawer runners onto the assembled drawer boxes. Use three panels (12), three panels (13), twenty-four screws (A), twenty-four cam locks (M), twelve screws (D), and six connectors (H). The diagram shows how to attach the runners to the drawer sides and the main unit. Note: Board 12 is the left drawer, Board 13 is the right drawer. Install drawers according to the illustration.
Step 13: Drawer Front/Back Attachment
Attach the drawer front/back panels (14, 15) to the drawer sides (12, 13) using twenty-four screws (D) and twelve connectors (G2). The diagram shows the drawer box assembly and the attachment of the front/back panels. Repeat for all six drawers.
Step 14: Drawer Installation
Install the assembled drawers into the main unit. The diagram shows the drawers being slid into place. It also shows a checkmark for correct installation and an 'X' for incorrect.
Step 15: Handle Attachment
Attach the drawer handles (J) and possibly decorative elements (I, K) to the drawer fronts. Use sixteen screws (D), sixteen connectors (I), two screws (J), and two screws (K). The diagram shows the attachment of handles and other hardware.
Step 16: Wall Securing
Secure the unit to the wall using anti-tip restraints. Use three brackets (18), eight screws (E), and two connectors (L). The diagram shows drilling holes in the wall, attaching brackets to the unit, and securing it to the wall.
Step 17: Final Check
Final check. Ensure all drawers are installed correctly. A note mentions removing a protective film from the panels before use. The diagram shows the completed unit.
Help Center & Disclaimer
Help Center: If you encounter any difficulties during assembly, please contact us for assistance with inquiries, assembly issues, or missing parts.
Disclaimer: The manufacturer and seller disclaim liability for personal injury, property damage, or loss resulting from incorrect attachment, improper use, inadequate maintenance, unapproved modification, or neglect of this product.
