VOVO USA Installation Manual

1 Cautions before Installation

Please note that these instructions may differ from the product specifications.

Installation Space

• Secure enough installation space in the bathroom and check whether it disturbs the bathroom door.
• Secure water outlet at least 100mm (approx. 4 inches) away from the floor. Failure to do so can cause wall discoloration.
• If you have a shorter rough-in than 11 inches (approx. 280mm), you can use an offset flange for installation.
• If you have a well water system, please contact VOVO USA support before installation.
• Email: support@vovousa.com

Diagram Description: Illustration showing required clearances for floor drain and water supply. Key dimensions indicated are: Water Supply 5.9in (150mm), 3.9in (100mm), 120V; Floor Drain installation space 12in (300mm). An 'Offset flange' is also depicted.

Water Pressure Requirements

• Minimum 1.5 kgf/cm² (STATIC 40PSI) water pressure is required. Insufficient pressure may result in improper flushing and failure to discharge waste effectively.
• Even when other water-using appliances are operated simultaneously, the bidet requires a minimum water pressure. The maximum recommended water pressure is 7.5 kgf/cm² (STATIC 75PSI).

Pre-installation Water Check

1. Direct the supply hose end into a 3-gallon (11.4L) or larger bucket.
2. Ensure the supply stop can provide a minimum of 1.5 gallons (5.7L) of water in 10 seconds.
3. Shut off the water supply before proceeding.

2 Drawing for Installation (unit: mm|in)

Diagram Description: This section provides dimensional drawings for various VOVO USA bidet toilet models. Specific model groups and their corresponding dimensions are illustrated:

• Remote control type PB-707S, PB-101S: Dimensions approximately 720/28.34 x 570/22.44.
• Models TCB 9100WA, TCB 9100GA, TCB 9100W, TCB 9100G: Dimensions approximately 410/16.14 x 720/28.34 x 570/22.44.
• Models TCB 090SA, TCB 090S, RTB 090WA, RTB 090W, TC-090, TC-090W: Dimensions approximately 725/28.54 x 535/21.06.
• Models TCB 8100B, TCB 8100W, TCB 8200SA, TCB 8200S, TCB 8200SA(Black), TCB 8200S(Black): Dimensions approximately 415/16.33 x 700/27.55 x 545/21.45.
• Models TCB 8100B, TCB 8100W, TCB 8200SA, TCB 8200S, TCB 8200SA(Black), TCB 8200S(Black): Dimensions approximately 390/15.35 x 660/25.98 x 550/21.65.

3 FAQ

Q: What are the electrical requirements? Is it energy efficient?

A: This item requires 6~10 Amps at 120V, 60 Hz. A separate circuit breaker is recommended. It features a power save mode that minimizes energy consumption.

Q: The Power Save LED light is flashing (turned off and on). What should I do?

A: Please open the water valve and check if water has entered the bidet. If the light continues to flash, try resetting the unit: unplug the power cord, wait 30 seconds, and then plug it back in. Please open the seat and the lid when resetting the bidet toilet.

Q: How long is the power cord?

A: The power cord is 4ft (1.2m) long.

4 Installation Accessories

A type Installation Accessories (Standard)

Recommended installation method. Requires installation by a plumber.

Diagram Description: Illustration of standard accessories for Type A installation. Includes: Remote control (note: each product may use a different remote controller), Wall Mount, 3x AA Batteries ?, 2x Screws ?, 2x Anchors ⚓, Wax Ring ?, Ring Plate, Water Pipe ?, Water Hose (Thicker, 1" x 5/8") ?, Water Shutoff Valve (1/2" x 5/8") ?, Strainer Filter (5/8" x 5/8") ?️, Rubber Washer ⚪.

B type Installation Accessories

Use Type B installation if Type A is inconvenient.

Diagram Description: Illustration of accessories for Type B installation. Includes: Remote control (note: each product may use a different remote controller), Wall Mount, 3x AA Batteries ?, 2x Screws ?, 2x Anchors ⚓, Wax Ring ?, Water Hose (Thin, 1" x 1/2") ?, Conversion Nut ?.

Note: You may need to use the included conversion nut to fit your water shutoff valve. Simply screw the conversion nut into the 1/2" side of the hose before connecting it to your water shutoff valve.

5 Installation Steps

A type Installation (Standard)

1. Close the water gauge.
2. Remove dust and sand from the water inlet before installing the shutoff valve.
3. Apply Teflon tape around the water pipe threads.
4. Connect the pipe to the shutoff valve.
5. Connect the Strainer Filter.

Diagram Description: Illustration showing incorrect connection of water pipe, shutoff valve, and strainer filter, with a warning symbol. Correct components are shown: Water Pipe (1/2"), Water Shutoff Valve (1/2" x 5/8"), Strainer Filter (5/8" x 5/8").

B type Installation Accessories

• Attach the provided water hose to your water shutoff valve.

Diagram Description: Diagram illustrating the connection of the water hose to the water shutoff valve, showing a 3/8" connection size.

How to install the Ceramic Toilet Bowl

Press firmly to seat the bidet onto the toilet base. Apply weight evenly and do not move the unit after placement to ensure a water-tight seal. A team of two people is recommended for correct placement of the toilet base.

Diagram Description: Diagram illustrating the placement of the ceramic toilet bowl onto the base, showing 'Toilet' and 'Bidet' components.

Connect Hose

1. Insert the brass part into the toilet's flushing outlet first.
2. Turn the nut clockwise to tighten the hose securely.

Diagram Description: Diagram showing the connection of the hose to the toilet's flushing outlet, detailing the 'Brass part', 'Hose Nut (1")', and 'Hose (5/8" x 1")'.

Connect Bidet to Toilet

1. Assemble the toilet with the bidet unit, ensuring the jet spray outlet and bowl washing outlet are correctly positioned.
2. Insert the bidet hose into the filter.
3. Align and insert the bidet's fixing hook onto the toilet's fixing hook until it 'clicks' into place.

Diagram Description: Exploded view diagram illustrating the connection of the bidet unit to the toilet. Key components shown include: Bidet, Toilet, Fixing hook ?, Bowl washing outlet ?, Jet spray outlet ?. Connections for both 'A type (Standard)' and 'B type' are depicted, including the Strainer Filter and hose connections.

Open the water shutoff valve.

Open the Water Valve

Diagram Description: Diagram showing the water shutoff valve being turned clockwise to reduce water pressure.

Note: In areas with high water pressure, water may overflow from the rim when cleaning the bowl. To prevent this, use a screwdriver to turn the shutoff valve clockwise to reduce the water pressure.

Connect Power

1. Insert the power plug into a suitable electrical outlet.
2. Press the flush button. Water will begin to fill the ceramic bowl.

Diagram Description: Illustration showing the final step of plugging the power cord into an electrical outlet and pressing the 'Full flush ▶️' button.