VOVO USA Installation Manual
This manual provides detailed instructions for installing VOVO USA Smart Bidet Toilets.
1 Cautions before Installation
Please observe the following precautions before installation. These may differ from specific product specifications.
- Ensure adequate installation space in the bathroom, checking for clearance with the bathroom door.
- Secure a water outlet at least 100mm (3.93 inches) away from the floor. Installation too close to the floor may cause wall discoloration.
- If your rough-in is shorter than 11 inches (280mm), an offset flange may be required for installation.
- If you use a well water system, please contact VOVO USA customer support before installation. Email: support@vovousa.com
Water Pressure Requirements:
- A minimum water pressure of 1.5 kgf/cm² (0.15 MPa) is required. Insufficient pressure may result in improper flushing.
- Even when using other fixtures simultaneously, the minimum required water pressure must be maintained. The maximum allowable water pressure is 7.5 kgf/cm² (0.75 MPa).
Extract Bad Water Before Installation:
- Direct the supply hose end into a bucket of at least 3 gallons (11.4 liters) capacity.
- Ensure the supply stop can provide a minimum of 1.5 gallons (5.7 liters) in 10 seconds.
- Shut off the water supply.
Proceed to the next step.
2 Drawing for Installation
Dimensions are provided in millimeters (mm) and inches (in).
Diagram Description: The diagram shows the spatial relationship between the floor drain, water supply, and the bidet toilet unit, including dimensions for optimal placement. It also illustrates the connection points for the water supply and drain, and the optional use of an offset flange.
Included Models:
- TCB 9100WA, TCB 9100GA, TCB 9100W, TCB 9100G
- TCB 090SA, TCB 090S, TCB 090SA (Black), TCB 090S (Black)
- RTB 090WA, RTB 090W
- TC-090, TC-090W
- TCB 8100B, TCB 8100W, TCB 8100N
- TCB 8200SA, TCB 8200S, TCB 8200SA (Black), TCB 8200S (Black)
Overall Dimensions (approximate):
- 410/16.14 x 720/28.34 x 570/22.44
- 410/16.14 x 725/28.54 x 535/21.06
- 415/16.33 x 700/27.55 x 545/21.45
- 390/15.35 x 660/25.98 x 550/21.65
3 FAQ
- Q: What are the electrical requirements? Is it energy efficient?
- A: The item requires 6-10 Amps at 120V, 60 Hz. A separate circuit breaker is recommended. The unit features a power-save mode that minimizes energy consumption.
- Q: The power-save LED light is flashing (turned off and on). What should I do?
- A: Please open the bidet's water valve. Check if water has entered the bidet. If the flashing persists, try resetting the unit: unplug the power cord, wait 30 seconds, and plug it back in.
- Q: How long is the power cord?
- A: The power cord is 4 feet (1.2 meters) long.
Note: Please open the seat and lid when resetting the bidet toilet.
4 Installation Accessories
The following accessories are typically included with the installation kit. Installation by a qualified plumber is recommended.
- Remote control (PB-707S, PB-101S)
- AA Batteries (x3)
- Screws (x2)
- Anchors (x2)
- Conversion Nut
- Wall Mount
- Wax Ring
- Water Hose (1" x 1/2")
5 Installation
5.1 Installation Accessories
- Attach the provided water hose to your water shutoff valve.
- A conversion nut may be needed to fit your specific water shutoff valve. Screw the conversion nut onto the 1/2" side of the hose before connecting it to the water shutoff valve.
5.2 How to install the Ceramic
Diagram Description: This section visually guides the installation of the ceramic toilet bowl. It shows pressing firmly, applying even weight, and avoiding movement after placement to ensure a watertight seal. It also recommends having two people for correct placement of the toilet base.
5.3 Connect Hose
- Insert the brass part of the hose into the flushing outlet.
- Turn the hose nut clockwise to tighten the hose. Hand-tighten only.
5.4 Connect Bidet to Toilet
- Assemble the toilet with the bidet, jet spray outlet, and bowl washing outlet.
- Insert the hose into the filter.
- Insert the bidet's fixing hook onto the toilet's fixing hook until it clicks.
5.5 Open the water valve
Diagram Description: This step involves opening the water valve. It shows a diagram of the water shutoff valve and the process of turning it clockwise. It also includes a note about potential water overflow from the rim when cleaning the bowl in areas with high water pressure, suggesting turning the shutoff valve clockwise with a screwdriver to reduce pressure.
5.6 Connect Power
Important: Please plug in the power only after completing all installation steps and opening the water valve.
- Insert the power plug into the outlet.
- Press the flush button. Water will fill the ceramic bowl.
