Vimar KNX XT Command Devices
This document provides technical specifications and installation guidelines for the Vimar KNX XT command devices, including models 32121.x, 32123.x, 32124.x, and 32144.x.
Product Descriptions
- 32121.x: Standard KNX XT command device with 2 pushbuttons, configurable as 1 rocker switch. Features status LED with dimmable night visibility and a central LED matrix for symbol customization or animation. Occupies 1 front module.
- 32123.x: Standard KNX XT command device with 2 pushbuttons, configurable as 1 rocker switch. Includes Proximity function, LED matrix for status indication or scene animation, dimmable night visibility, and a central LED matrix for symbol customization or animation. Occupies 1 front module.
- 32124.x: Standard KNX XT command device with 4 pushbuttons. Features Proximity function, status LED with dimmable night visibility. Occupies 1 front module.
- 32144.x: Standard KNX XT command device with 4 pushbuttons featuring backlit CLIMATE symbols and dimmable night visibility. Occupies 1 front module.
Features
- Power Supply: Supplied by electrified XT support (art. 32602.x, 32603.x, 32604.x, 32613.x, or 32614.x) and corresponding node (art. 32101).
- Maximum BUS Absorption:
- 32121.x: 7.5 mA
- 32123.x, 32124.x, 32144.x: 12.5 mA
- Red LED and configuration/reset button.
- Operating Temperature: -5°C to +45°C (internal use).
- Occupies 1 front module (30.5 mm).
- Selectable standby brightness levels via parameters.
- Rear connection to electrified support (art. 32602.x, 32603.x, 32604.x, 32613.x, or 32614.x).
- Protection Rating: IP20.
Feature Comparison Table
| Feature | Art. 32121.x | Art. 32123.x | Art. 32124.x | Art. 32144.x |
|---|---|---|---|---|
| 2 pushbuttons, configurable as 1 rocker switch | ✔ | ✔ | ||
| Central white LED matrix for programmable symbols or animation | ✔ | ✔ | ||
| Vertical white LED cursor for animation | ✔ | ✔ | ||
| 2 white LEDs (top and bottom) for status indication | ✔ | |||
| Top and bottom white LED matrices for programmable symbols for status indication or animation | ✔ | |||
| 4 pushbuttons | ✔ | ✔ | ||
| 4 white LEDs next to buttons for status indication | ✔ | |||
| 4 backlit CLIMATE symbols next to buttons for thermostat status indication | ✔ | |||
| Proximity Function | ✔ | ✔ |
Configuration
The device and its parameters are configured using ETS software. Updated ETS databases can be downloaded from the "Software" section of the Vimar website: www.vimar.com.
Installation Guidelines
- Installation must be performed by qualified personnel in compliance with current regulations for electrical material assembly in the country of installation.
- The device must be mounted on electrified XT supports:
- 2 modules: art. 32602.x (for 2-module boxes)
- 3 modules: art. 32603.x and 32613.x (for rectangular 3-module boxes)
- 4 modules: art. 32604.x and 32614.x (for rectangular 4-module boxes)
- To optimize operation, it is advisable to activate only one proximity sensor (proximity function) per light point, deactivating the others.
- Avoid mounting two or more command devices with an activated proximity sensor facing each other at a distance of less than 4 meters: [X symbol indicating prohibition]
- Avoid mounting a button with an activated proximity sensor in front of a device with an infrared receiver to prevent potential interference.
- During the button removal and attachment phases, be careful not to soil or scratch the proximity sensor lens.
Compliance with Standards
Electromagnetic Compatibility Directive. Directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment. Standards EN IEC 60669-2-1, EN 50491-2, EN IEC 63044, and EN IEC 63000. REACH Regulation (EU) No. 1907/2006 - art. 33. The product may contain traces of lead.
Device Attachment and Detachment
Attachment:
- [Image description: Shows the front module being aligned with the backplate.]
- [Image description: Shows the front module being pressed onto the backplate until it clicks.]
- [Image description: Side view of the attached device.]
Detachment:
- [Image description: Shows a tool being inserted into a slot to release the front module.]
- [Image description: Shows the front module being gently pulled away from the backplate.]
- [Image description: Shows the detached front module.]
WEEE - User Information
The crossed-out bin symbol on the equipment or its packaging indicates that at the end of its life, it must not be disposed of with other waste. At the end of its useful life, the user must deliver the equipment to a collection center for electrical and electronic waste. Used equipment can also be returned free of charge to the retailer where a new equivalent product was purchased. Retailers of electronic equipment with a sales area of at least 400 m² must accept used electronic products smaller than 25 cm free of charge, without the obligation to purchase. Selective collection of this waste facilitates the recycling of the apparatus and its components, allows for environmentally compatible treatment and disposal, and prevents potential adverse effects on nature and human health.
Front and Rear View
Diagrams showing the front and rear views of models 32121.x, 32123.x, 32124.x, and 32144.x.
- A: Red LED
- B: Proximity sensor
- C: Configuration/reset button
- D: Button and white LED
- E: Button and white LED matrix
Vimar S.p.A., Viale Vicenza, 14 36063 Marostica VI - Italy. www.vimar.com
