LIVINOX USER MANUAL

From the Manufacturer

Please read this user manual carefully before attempting to operate the appliance and keep it in a safe place for future reference. This appliance and its packaging are produced by processes that minimize waste and respect the environment. Please help us to continue this effort to protect the environment by using the appliance efficiently and dispose of the packaging in a responsible manner.

1. Safety Instruction

Warning

⚠️ PLEASE READ THIS SECTION THOROUGHLY BEFORE ATTEMPTING TO OPERATE THE APPLIANCE

• To ensure adequate ventilation in the room when the range hood is in use at the same time as gas/fuel burning cooking appliances (this is not applicable to appliances that only discharge the air back into the room).
• There is a fire risk if cleaning is not carried out in accordance with the instructions.
• To avoid using food products that produce flame under the range hood.
• Do not "flambé" food (is a cooking procedure in which alcohol is added to a hot pan to create a burst of flames) under the range hood.
• Sufficient air is needed for proper exhausting of gases through flue (chimney) of fuel burning appliances.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory, mental capabilities, lack of experience and knowledge.
• To reduce risk of fire and to properly exhaust air and to ensure to duct air outside. Do not vent exhaust air into spaces within walls, ceilings, into attics and crawl spaces.

Electrical Cord

• To ensure the electrical cord is not exposed to heat, chemical or sharp objects.
• If the electrical cord is damaged, it must be replaced by the manufacturer or its service agent or qualified electrician.

Installation

• This appliance must be installed or repaired by a qualified technician only.
• Do not modify any part of this appliance by yourself.
• To ensure the location in which this appliance is installed has good and permanent ventilation.
• In ducted mode, there must be one or more permanent air inlet. The air collected must not be discharged into a duct used to blow off smoke from other appliances fed with electricity.
• The distance between the bench to the lower part of the hood must not be less than 60cm.
• Use an electrical connector with earth that is correct for your location.
• To check the voltage in your area correspond to the appliance as indicated on the rating label.
• Do not connect the hood to a duct that carries combustion fumes (e.g. fireplace).

Intended For Household Use

• This product is designed for household use only and should never be used for commercial applications.
• After use, always ensure that all controls are in the "OFF" position.
• When frying with a gas flame, take particular care not to allow the oil or grease in the pan to catch fire.

2. Hood Description

Cleaning, Maintenance & Service

It is very important to clean and maintain the grease filters regularly (at least once monthly) to improve its efficiency in eliminating heat and contaminated air in the kitchen. Heavy oil deposits is a fire hazard. Hood surface should be cleaned with soft cloth and non-corrosive detergent.

Important: Never attempt to repair this appliance by yourself. Always refer to qualified Service Technicians. For safety precaution, always purchase the original replacement parts. Always switch off the power and unplug the connection before conducting maintenance or cleaning.

Ducted or Re-circulating mode

Depending on your requirement, this appliance can be configured to operate in the ducted or re-circulating modes.

DUCTED MODE: Fire proof ducting system of 160mm or 180mm diameter vent the fumes through a suitable outlet. In the ducted mode, only the aluminum grease filters are installed.

RECIRCULATING MODE: Fumes are filtered for grease and odour through the aluminum grease filters and the charcoal filters respectively and re-introduced into the kitchen environment. In re-circulating mode, both the aluminum grease filters and the charcoal filters should be installed.

Speed Control

Use the low speed for simmering, medium speed for light cooking and higher speed/turbo for frying or heavy cooking.

3. Dimension Diagrams

LCH-ANGEL DC-90FG

Diagram shows a range hood with overall width 895mm, depth 309mm (hood body) / 386mm (front panel), and height 406mm (hood body) with an adjustable chimney up to MAX 1230mm. The front panel height is 480mm. Side panel thickness is 33mm.

LCH-SUGI DC-90FB

Diagram shows a range hood with overall width 895mm, depth 309mm (hood body) / 386mm (front panel), and height 416mm (hood body) with an adjustable chimney up to MAX 1340mm. The front panel height is 480mm. Side panel thickness is 34mm.

4. Instructions for use Touch control

MOTION SENSOR

To turn on the power, wave once from left to right ? within 10-15 cm from the switch (the LED screen will display "F1"). Repeating this action will increase the speed from F2 up to the highest setting, F5. To turn off the power, wave once from right to left ?.

i-Sync FUNCTION

When the device is not in use, press and hold the ? icon for 3 seconds to enter pairing mode. The ? icon will begin flashing. Then, turn the hob knob to the ON position. Once the hob and hood are successfully paired, the ? icon will stop flashing, and the hood will automatically power on and begin operation. When the hob is turned off, the hood will enter a delayed shutdown mode. To disconnect this function, press and hold the ? icon for 3 seconds again.

Note: This feature is available on certain hob models only. Adjusting the flame power will automatically adjust the hood's air volume.

Controls

Turbo Button: Press to set the fan to booster/highest speed (LED screen displays "F6"). After 3 minutes, it automatically switches to high-speed mode. Press again to stop the motor.

Speed Button: Press to adjust fan speed:

• At low speed, the LED screen displays "F1".
• Press once to switch to medium speed ("F2").
• Continue pressing to increase speed until the highest setting ("F5"). The cycle repeats.

Auto Clean Button: In Standby Mode, press and hold the ✨ button for 3 seconds to activate the oil removal function, which runs for 10 minutes. Press again to turn it off. The fan switches to high speed for 1 minute after 9 minutes of cleaning. The Auto Clean function activates automatically after 30 hours of use. Once the 10-minute cleaning process is complete, usage time resets.

Setting the Clock

In Standby Mode, press and hold the ⏰ button for 3 seconds. The hour digits blink. Use the buttons to set the hour:

• Press ➕ (Speed) to increase.
• Press ➖ (Light) to decrease.

Press the ⏰ button again to move to the minutes. The minute digits blink. Adjust minutes using ➕ (Speed) to increase, ➖ (Light) to decrease. Press the ⏰ button one final time to save the time.

Powering the Device On/Off

• To turn the device on, press the ⏻ button.
• While operating, press the ⏻ button again to enable the Delay Off feature (initially set to 1 minute).

Adjusting the Delay Off Timer (1 to 99 minutes)

• When setting the timer, the Speed and Light icons will flash.
• Press the ➕ (Speed) button to increase timer duration.
• Press the ➖ (Light) button to decrease timer duration.

Press the ? button to turn the light on. Press it again to turn the light off.

Cleaning & Maintenance

⚠️ ALWAYS SWITCH OFF AND UNPLUG FIRST!

SURFACES:

Wash with warm soapy water and a soft sponge. Never use abrasive detergent, scouring pads, steel wool or solvents on any part of this appliance as this will cause irreparable damage.

ALUMINIUM GREASE FILTERS:

Wash in dishwashers or soak panels in a degreasing agent for an hour, then rinse off and dry before re-installing.

CHARCOAL FILTERS: (optional and not included in package)

(only in re-circulating model): Charcoal cannot be reused. They must be replaced with appropriate types once a year or depending on appliance usage frequency. For this appliance to function effectively, regular maintenance is a must. Clogged filters restrict airflow and may cause the motor to overheat.

5. Installation

1. Use suitable bolts to mount the appliance on a secure surface.

2. The minimum distance between the supporting surface for cooking vessels on the hob and the lowest part of the range hood shall be at least 65 cm. If the range hood is located above a gas appliance, and the gas hob instructions specify a greater distance, this must be taken into consideration.

3. The installation location must have permanent openings for ventilation.

4. Regulations concerning the discharge of air must be fulfilled.

5. It is strongly recommended that the hood be installed directly over the exhaust air from cooking.

6. Do not install the outlet of the pipe in the wind direction, which can prevent exhaust air from flowing backward.

7. Fasten components for the exhaust outlet with screws. To ensure good ejection of exhaust air, the pipe must not be bent too many times.

Diagram Description:

The diagram illustrates typical installation clearances and ducting. It shows distances from the floor to the hob (800-850mm), from the hob to the bottom of the hood (350-400mm), and from the hob to the ceiling (600-800mm). The ducting is shown with a minimum bend radius of 150mm.

Installation (Vent inside)

If you do not have an outlet to the outside, an exhaust pipe is not required, and the installation is similar to the one shown in section "Installation (Vent outside)".

Activated carbon filters can be used to trap odors. To install an activated carbon filter, detach the grease filter first by pressing the lock and pulling it downward. Then, plug the activated carbon filter into the unit and turn it clockwise. Repeat the same on the other side.

Diagram Description:

Diagrams show the process of removing the grease filter by pressing a latch and pulling it down. Subsequent diagrams show the activated carbon filter being inserted and rotated clockwise into place.

IMPORTANT NOTES:

• Ensure the activated carbon filter is securely locked.
• When an activated carbon filter is attached, suction power will be lower.
• Check that the electrical connection corresponds to the electrical requirement on the rating plate inside the cooker hood. The appliance should now be connected to the electrical supply.
• Check the appliance is operating correctly by selecting each speed and switching the light on and off.
• To remove the hanging hook and slide the lower chimney section downwards until it rests against the main body of the cooker hood.
• Use a stainless-steel cleaner and polish on the stainless steel surfaces of the appliance.
• If using in recirculation mode, install the carbon filter (see "fitting the carbon filter" section on page 21).
• Every hood has two fixing screws to firmly fix the hood in its place.

FOR THE INSTALLER

6. Safety Information

• Electrical connection must be in accordance with local standards and laws.
• Ensure the electrical supply complies with the appliance settings; otherwise, do not connect.
• Ensure the power supply cord is free from heat sources or sharp objects.
• The electrical connection must be soundly earthed. Grounding reduces the risk of electrical shock in case of a short circuit. If unsure, contact a qualified electrician.
• Replacement of lamp must not exceed 20W.
• LED lamp must not exceed 1.5W/7W.

Wire Color Codes:

• Green & Yellow = EARTH
• Blue = NEUTRAL
• Brown = LIVE

7. Trouble shooting

Contact Information

Livinox Malaysia Sdn Bhd (1089457-U)

No 32A, Jalan Teknologi 3/3A, Taman Sains Selangor 1, Kota Damansara, 47810 Petaling Jaya, Selangor.

Website: www.livinox.my

Careline: +603-6150 7810