LIVINOX LCH-OCEAN-90BL Range Hood

From the Manufacturer

Please read this user manual carefully before attempting to operate the appliance and keep it in a safe place for future reference.

This appliance and its packaging are produced by processes that minimize waste and respect the environment. Please help us to continue this effort to protect the environment by using the appliance efficiently and dispose of the packaging in a responsible manner.

FOR THE USER

1. Safety Instruction

Warning: PLEASE READ THIS SECTION THOROUGHLY BEFORE ATTEMPTING TO OPERATE THE APPLIANCE

1. To ensure adequate ventilation in the room when the range hood is in use at the same time as gas/fuel burning cooking appliances (this is not applicable to appliances that only discharge the air back into the room).
2. There is a fire risk if cleaning is not carried out in accordance with the instructions.
3. To avoid using food products that produce flame under the range hood.
4. Do not "flambé" food (a cooking procedure in which alcohol is added to a hot pan to create a burst of flames) under the range hood.
5. Sufficient air is needed for proper exhausting of gases through the flue (chimney) of fuel burning appliances.
6. This appliance is not intended for use by persons (including children) with reduced physical, sensory, mental capabilities, or lack of experience and knowledge.
7. To reduce risk of fire and to properly exhaust air, ensure to duct air outside. Do not vent exhaust air into spaces within walls, ceilings, attics, or crawl spaces.

Installation

1. This appliance must be installed or repaired by a qualified technician only.
2. Do not modify any part of this appliance by yourself.
3. To ensure the location in which this appliance is installed has good and permanent ventilation.
4. In ducted mode, there must be one or more permanent air inlets. The air collected must not be discharged into a duct used to blow off smoke from other appliances fed with electricity.
5. The distance between the bench to the lower part of the hood must not be less than 60cm.
6. Use an electrical connector with earth that is correct for your location.
7. Check the voltage in your area corresponds to the appliance as indicated on the rating label.
8. Do not connect the hood to a duct that carries combustion fumes (e.g., fireplace).

Intended For Household Use

1. This product is designed for household use only and should never be used for commercial applications.
2. After use, always ensure that all controls are in the [Off] position.
3. When frying with a gas flame, take particular care not to allow the oil or grease in the pan to catch fire.

Cleaning, Maintenance & Service

It is very important to clean and maintain the grease filters regularly (at least once monthly) to improve its efficiency in eliminating heat and contaminated air in the kitchen. Heavy oil deposits are a fire hazard. The hood surface should be cleaned with a soft cloth and non-corrosive detergent.

Important: Never attempt to repair this appliance by yourself. Always refer to qualified Service Technicians. For safety precaution, always purchase original replacement parts. Always switch off the power and unplug the connection before conducting maintenance or cleaning.

Electrical Cord

1. To ensure the electrical cord is not exposed to heat, chemical, or sharp objects.
2. If the electrical cord is damaged, it must be replaced by the manufacturer or its service agent or qualified electrician.

2. Hood Description

Ducted or Re-circulating mode

Depending on your requirement, this appliance can be configured to operate in the ducted or re-circulating modes.

DUCTED MODE: Fire proof ducting system of 160mm or 180mm diameter vents the fumes through a suitable outlet. In the ducted mode, only the aluminum grease filters are installed.

RECIRCULATING MODE: Fumes are filtered for grease and odour through the aluminum grease filters and the charcoal filters respectively and re-introduced into the kitchen environment. In re-circulating mode, both the aluminum grease filters and the charcoal filters should be installed.

Speed Control

1. The hood is equipped with 3 or 4 speed mechanical/electronic controls.
2. Use the low speed for simmering, medium speed for light cooking. Use the high speed for frying or heavy cooking.

3. Dimension Diagrams

Dimension diagrams show the physical specifications of the LCH-OCEAN-90BL range hood. Key dimensions include: overall width of 898mm, main body height of 486mm, duct opening height of 293mm, duct opening width of 370mm, maximum chimney height of 790mm, and a depth of 400mm. Other noted dimensions are 17.5mm and 24mm.

K. Touch control (LCH-OCEAN-90BL)

Control A: Wave gesture. Wave [Left-to-right]: Power and lighting turn [On] (LED screen shows "11"). Wave to the right again: Fan runs at mid speed (LED screen shows "22"). Wave to the right again: Fan runs at high speed (LED Screen shows "33"). "Repeat this cycle".

Control B: Press. Fan runs at low speed (LED screen shows "11"). Press once: Fan runs at mid speed (LED screen shows "22"). Press again: Fan runs at high speed (LED Screen shows "33"). Press again: 1 minute delay power off. "Repeat this cycle".

Control C: Press. Fan runs at low speed (LED screen left shows "1"). Press once: Fan runs at mid speed (LED screen left shows "2"). Press again: Fan runs at high speed (LED Screen left shows "3"). Press again: 1 minute delay power off. "Repeat this cycle".

Control D: Press. Fan runs at low speed (LED screen right shows "1"). Press once: Fan runs at mid speed (LED screen right shows "2"). Press again: Fan runs at high speed (LED Screen right shows "3"). Press again: 1 minute delay power off. "Repeat this cycle".

Control E: Press to turn [On] power. Press again to turn [Off] power. In non-working state, press E for 3 seconds: oil removing function operates for 10 minutes. Press again: turn off oil removing function. The fan will automatically operate at high speed for 30 seconds after the 10 minutes cleaning function.

Control F: Wave gesture. Wave [Right-to-left] to turn [Off] power.

Cleaning & Maintenance

ALWAYS SWITCH OFF AND UNPLUG FIRST!

SURFACES:

Wash with warm soapy water and a soft sponge. Never use abrasive detergent, scouring pads, steel wool, or solvents on any part of this appliance as this will cause irreparable damage.

ALUMINIUM GREASE FILTERS:

Wash in the dishwasher or soak the panels in a degreasing agent for an hour, then rinse off and dry before re-installing.

CHARCOAL FILTERS: (optional and not included in package)

(Only in re-circulating model): Charcoal cannot be reused. They must be replaced with the appropriate types once a year or depending on the frequency of appliance usage.

For this appliance to function effectively, regular maintenance is a must. Clogged filters restrict airflow and may cause the motor to overheat.

5. Installation (For the Installer)

Use suitable bolts to mount the appliance on a secure surface. The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood must be considered. When the range hood is located above a gas appliance, this distance shall be at least 65 cm. If the instructions for installation for the gas hob specify a greater distance, this must be taken into consideration.

The installation location must have permanent openings for ventilation. Regulations concerning the discharge of air must be fulfilled. It is strongly recommended that the hood be installed directly over the exhaust air from cooking. Do not install the outlet of the pipe in the wind direction, which can prevent the exhaust air from flowing backward. Fasten the components for the exhaust outlet with screws. To ensure good ejection of exhaust air, the pipe must not be bent too many times.

Installation diagrams illustrate mounting procedures and ducting configurations. They show the appliance being fixed to a secure surface using bolts. Recommended minimum distances are indicated, particularly for gas appliances (at least 65cm from hob to hood). Ventilation openings are crucial. Ducting systems are shown with diameters of 160mm or 180mm, emphasizing proper exhaust flow and avoiding excessive bends in the pipe.

6. Safety Information (For the Installer)

1. Electrical connection must be in accordance with local standards and laws.
2. To ensure the electrical supply complies with the appliance settings; otherwise, do not connect.
3. Ensure the power supply cord is free from any heat source or sharp objects.
4. The electrical connection of this appliance must be soundly earthed. In the event of an electrical short circuit, grounding reduces the risk of electrical shock. If unsure, contact a qualified electrician.
5. Replacement of lamp must not exceed 20W.
6. LED lamp must not exceed 1.5W/7W.

Wire Color Codes:

Green & Yellow = EARTH

Blue = NEUTRAL

Brown = LIVE

7. Trouble shooting