POVA 5 Pro 5G User Manual
Explosion Diagram Specification
The following table details the components of the POVA 5 Pro 5G:
| Part Number | Component Name | Part Number | Component Name |
| 1 | LCM+TP | 2 | RECEIVER DECORATING PART |
| 3 | FRONT HOUSING | 4 | VC |
| 5 | FRONT HOUSING | 6 | SIDE KEY FPC |
| 7 | 16M CAMERA RUBBER | 8 | 16M CAMERA |
| 9 | PROXIMITY SENSOR RUBBER | 10 | MAIN BOARD |
| 11 | CONDUCTIVE FABRIC | 12 | 16M CAMERA FRAME |
| 13 | BATTERY CONNECTOR RUBBER | 14 | MAIN GRAPHITE_FILM |
| 15 | 8W CAMERA FRAME | 16 | 50M CAMERA COPPER FOIL |
| 17 | 8W CAMERA | 18 | FLASH LAMP FPC |
| 19 | 50M CAMERA | 20 | MAIN BOARD FRAME |
| 21 | MAIN BOARD FRAME MYLAR | 22 | RECEIVER |
| 23 | SCREW M1.4 L3.5 | 24 | LAMP FPC |
| 25 | NFC | 26 | MIDDLE HOUSING GRAPHITE_FILM |
| 27 | 50M CAMERA FRAME | 28 | 50M CAMERA LENS |
| 29 | 8W CAMERA LENS | 30 | CAMERA DECORATING PART |
| 31 | SIM CONNECTOR | 32 | BATTERY COVER |
| 33 | SPEAKER GRAPHITE FILM | 34 | FINGERPRINT MYLAR |
| 35 | SPEAKER FRAME | 36 | MIDDLE HOUSING |
| 37 | COAXIAL CABLE 2 | 38 | COAXIAL CABLE 1 |
| 39 | SUB BOARD RUBBER | 40 | FINGERPRINT |
| 41 | MAIN FPC | 42 | SUB BOARD |
| 43 | EARPHONE RUBBER | 44 | BATTERY |
| 45 | MOTOR | 46 | SPEAKER |
| 47 | USB RUBBER | 48 | ADHESIVE |
Know Your Phone
This section identifies the key external components of the POVA 5 Pro 5G:
Front View:
- 1. Front camera
- 2. Volume + key
- 3. Volume - key
- 4. Power key & side fingerprint sensor
Back View:
- 5. NFC (Near Field Communication) area
SIM/SD Card Installation
To install a SIM or SD card:
- Power off the mobile device.
- Refer to the diagram for correct SIM/SD card placement. The device supports dual SIM cards (SIM 1 and SIM 2) and one SD card.
Charging the Phone
You can charge your TECNO POVA 5 Pro 5G using either a TECNO-approved charger or by connecting it to a computer via a USB cable. It is recommended to use only official TECNO chargers and cables to prevent device damage and warranty invalidation.
FCC Caution
Labelling Requirements:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- (1) This device may not cause harmful interference.
- (2) This device must accept any interference received, including interference that may cause undesired operation.
Information to User:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note on RF Interference:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) Information:
This mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards developed by independent scientific organizations through periodic and thorough evaluation of scientific studies, including a substantial safety margin designed to assure the safety of all persons regardless of age or health.
The SAR limit of the USA (FCC) is 1.6 W/kg averaged over one gram of tissue. The TECNO POVA 5 Pro 5G (Device type: LH8n, FCC ID: 2ADYY-LH8N) has been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 0.720W/kg, and when properly worn on the body is 0.578W/kg. This device was tested for typical body-worn operations with the back of the handset kept 10 mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 10 mm separation distance between the user's body and the back of the handset. Accessories like belt clips and holsters should not contain metallic components. Accessories that do not meet these requirements may not comply with FCC RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
Body-worn Operation:
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user's body and the handset, including the antenna. Third-party accessories such as belt clips and holsters should not contain metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
