SOFA
Assembly Instruction
Safety and Care Advice
Important: Please read these instructions fully before starting assembly.
Thank you for your purchase. Before assembly, please follow the instructions to check if all spare parts and screws are intact.
Considering the size and weight of the sofa, we recommend two adults to assemble the sofa on a carpeted or padded area, in the room where it is intended for. Approximate assembly time: 30 minutes.
Please do not throw away any of the packaging or the instructions until you have checked all components and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe and environmentally friendly way.
Keep all components and packaging out of reach of children or animals to avoid the risk of choking or suffocation.
Please do not remove the cover, and do not wash.
Your cushions come vacuum-packed and sealed for shipping. To restore the cushions' original shape, follow the steps below:
- Open the vacuum bag carefully.
- Press and tap with both hands from the side to fully inflate.
- Press and tap with both hands from the front to fully inflate.
- Carefully smooth out each section until the surface is even.
After unpacking, place them in a dry and ventilated area. After about 72-96 hours, they can be restored to their best use condition.
Assembly Instruction of Sofa
Hardware Parts
| Part | Description | Quantity |
|---|---|---|
| (a) | 6*18MM Washer | x16 |
| (b) | 6*30MM Bolts | x16 |
| (c) | Allen Key | x1 |
Structural Accessories
| Part | Description | Quantity |
|---|---|---|
| (1) | Sofa Leg | x4 |
| (2) | Middle Leg | x2 |
Main Structure Accessories
- (A-1) 1pc Armrest (Left)
- (A-2) 1pc Armrest (Right)
- (A-3) 1pc Back Frame
- (A-4) 1pc Front Bezel
- (A-5) 1pc Seat Frame
- (A-6) 2pcs Seat Foam
- (A-7) 2pcs Seat Pad Cover
- (A-8) 3pcs Throw Pillow
Assembly Steps
Step 1
Take out the throw pillows (A-8) from the bottom of the armrests (A-1 and A-2).
Step 2
Attach the sofa legs (1) to the bottom of the armrests (A-1 and A-2) using washers (a) and bolts (b), and tighten with the Allen key (c). The diagram shows 4 legs (1) being attached to the armrests (A-1 and A-2) with hardware (a) and (b).
Step 3
Connect the left armrest (A-1) and right armrest (A-2) to the front bezel (A-4) using bolts (b) and washers (a). The diagram shows the front bezel (A-4) being attached between the two armrests (A-1 and A-2) using hardware (a) and (b).
Step 4
Attach the seat frame (A-5) to the assembled structure. The diagram shows the seat frame (A-5) being placed and secured onto the base structure.
Step 5
Attach the front bezel (A-4) to the front of the seat frame (A-5). The diagram shows the front bezel (A-4) being attached to the front edge of the seat frame (A-5).
Step 6
Attach the back frame (A-3) to the rear of the assembled structure. The diagram shows the back frame (A-3) being attached to the back of the sofa base.
Step 7
Prepare the seat cushions:
- Open the sealed bag for the seat foam (A-6).
- Take out the seat foam (A-6).
- Insert the seat foam (A-6) into the seat pad cover (A-7).
- Ensure the white side of the seat pad cover is facing up and towards the front.
Step 8
Place the prepared seat cushions (A-7) onto the sofa frame. The diagram shows two seat cushions being placed onto the seat frame (A-5).
Step 9
Place the throw pillows (A-8) onto the sofa. The diagram shows three throw pillows being placed on the assembled sofa.
