Outsunny 845-841V01 Outdoor Storage Shed

Assembly Preparation

Before beginning construction, please check local building codes regarding footings, location, and other requirements. Study and understand this owner's manual for important information and helpful tips for easier and more enjoyable assembly.

Assembly Instructions

Review all instructions and the appropriate information before you begin. Make sure to follow the step sequence carefully for successful results.

Flooring Base

The site must be prepared so that the base of the shed is level all around, verified with a spirit level [spirit level]. The base can be constructed from treated timber or concrete to prevent moisture ingress. The shed is not designed to be built directly onto lawn, as the ground can become muddy during rainy days. If a concrete pad is made, it is important that it slopes towards the edges to prevent water ingress. Allow adequate time for any concrete or cement to dry before building the shed on top. Bases can also be constructed from bricks, blocks, or mounted on a concrete pad. Bricks or blocks should be cemented onto firm and level concrete footings, and the shed frame drilled and screwed to the base.

Parts and Parts List

Before you start, separate and identify all the parts and hardware to ensure you have all the necessary components for your building. Refer to the Parts List page for details. Do not attempt to assemble the building if parts are missing, as any partially assembled building may be seriously damaged by light winds.

Safety Must Be Prioritized

1. Select a dry and calm day for your assembly. Teamwork ([two or more people]) is required.
2. Wear safety gloves [gloves], eye protection [safety glasses], and long sleeves during assembly to prevent injury. Pay attention to the sharp edges of some parts.
3. Children and pets are not allowed on the construction site.
4. Never concentrate your total weight on the roof of the building. When using a step ladder [step ladder], ensure it is safe.

Care & Maintenance

1. Keep the shed clean with a soft cloth, using water if necessary.
2. Keep the door tracks clear of dirt and other debris that may prevent them from sliding easily.
3. Clean snow with necessary tools to ensure safe entry. Heavy snow may cause collapse; ensure safety before entering.
4. The shed is not made for living but for storing items.

Handling Bent Corners

NOTICE: If there is slight bending on the corners:

1. Please wear gloves [gloves] and stretch the corners slightly until they are flat.
2. The sheets will then be normal, with no effect on the assembly.

Parts Identification

The following diagram shows an exploded view of the shed components. Refer to the parts list for quantities.

[Diagram showing various parts labeled with numbers and letters like GC, 15, P6, P7, 21L, 12R, B1, 10, 9R, 12L, 9L, 7, P3, P1, 5, 6, 21R, JM6, DH, 25R, DC, DX1, DRA, DF, DG, DLA, 25L, 20, 22, M5, 4, W1, W3, W2, 3, 1, 2.]

Parts List

BOX 1

BOX 2

Hardware List

Assembly Steps

Step 1

Assemble two frame sections. Connect part 2 (2 pieces) and part 3 (2 pieces) using F1 screws (8 pieces). This creates two identical frame sections.

Step 2

Connect the two frame sections assembled in Step 1. Use part 4 (1 piece) and F1 screws (4 pieces) to join the sections.

Step 3

Form the base frame. Connect parts 1 (1 piece), 2 (2 pieces), 3 (1 piece), and 4 (1 piece) using F1 screws (4 pieces) to create a rectangular base structure.

Step 4

Attach vertical supports and horizontal beams to the base. Attach part 6 (1 piece) vertically and horizontal beams P1 (1 piece) and 25L (1 piece) to the base frame using F1 screws (8 pieces) and S2 washers (8 pieces).

Step 5

Attach more horizontal beams to the vertical supports. Add parts P1 (1 piece) and 5 (1 piece) using F1 screws (8 pieces) and S2 washers (8 pieces).

Step 6

Attach additional horizontal beams. Add parts P3 (1 piece) and 5 (1 piece) using F1 screws (8 pieces) and S2 washers (8 pieces).

Step 7

Attach more vertical supports and horizontal beams. Attach part 6 (1 piece) and P1 (1 piece) using F1 screws (8 pieces) and S2 washers (8 pieces).

Step 8

Attach more horizontal beams. Add parts 25L (1 piece) and P1 (1 piece) using F1 screws (8 pieces) and S2 washers (8 pieces).

Step 9

Install side wall panels. Attach multiple P1 panels (8 pieces total) and P3 panels (2 pieces total) to the frame using F1 screws (80 pieces) and S2 washers (80 pieces). This step utilizes a double-layer board lap method.

Step 10

Install more side wall panels. Attach P1 panels (1 piece) using F1 screws (32 pieces) and S2 washers (32 pieces). This step also uses the double-layer board lap method.

Step 11

Install upper side panels. Attach 9L (2 pieces) and 9R (2 pieces) to the upper part of the frame using F1 screws (8 pieces) and S2 washers (8 pieces).

Step 12

Install roof support beams. Attach part 10 (1 piece) and P3 (1 piece) to the top frame using F1 screws (10 pieces) and S2 washers (10 pieces).

Step 13

Install roof support beams. Attach part 7 (1 piece) to the top corners using F1 screws (2 pieces). Ensure correct placement orientation.

Step 14

Assemble door frame parts. Connect parts 12L (1 piece) and 12R (1 piece) using B1 (2 pieces) and F2 screws (2 pieces). A 60° angle is indicated for alignment.

Step 15

Attach roof panels. Secure 21L (1 piece) and 21R (1 piece) roof panels to the frame using F2 screws (4 pieces), F1 screws (16 pieces), and S2 washers (20 pieces).

Step 16

Attach more roof panels. Secure P6 (4 pieces) and P7 (3 pieces) roof panels using F1 screws (34 pieces) and S2 washers (34 pieces). Details for overlapping panels are shown.

Step 17

Secure roof panels and trim. Attach parts 15 (2 pieces), 16 (2 pieces), 17 (2 pieces), and GC (4 pieces) corner pieces to the roof structure using F1 screws (6 pieces) and S2 washers (2 pieces).

Step 18

Attach bottom corner braces. Secure JM6 (4 pieces) braces to the bottom corners of the shed using F1 screws (20 pieces).

Step 19

Identify door components. This step shows various parts for door assembly including 20, 21, DC, DX1, DLA, DF, DG, DRA, 22, and DH.

Step 20

Assemble the door frame with panels. Connect parts labeled 20, DX1, DLA, DRA, 21, and 22 using F1 screws (40 pieces) to form the door structure.

Step 21

Attach door hardware. Install hinges (DF, DG) and other hardware onto the door panels using F4 screws (5 pieces).

Step 22

Attach door handles and latches. Secure DH parts (4 pieces) to the doors using F3 screws (16 pieces).

Step 23

Final assembly of the shed structure. The diagram shows the completed shed with doors installed.

Step 24

Install door lock mechanism. Use F1 screws and S1 washers to attach the lock components to the doors.

Step 25

Attach floor support beams. Secure W1 (2 pieces), W2 (2 pieces), and W3 (4 pieces) floor support beams to the base frame using F1 screws (16 pieces).

Step 26

Attach corner supports. Install M5 (4 pieces) corner brackets to reinforce the structure.

Step 27

Install the lock. Attach the provided lock (1 piece) to the doors.

Step 28

Final view of the assembled Outsunny 845-841V01 outdoor storage shed.

Contact Information

For any questions or assistance, please refer to the contact details provided for your region:

USA

Customer Care Center: 001-877-644-9366

Email: customerservice@aosom.com

Imported by Aosom LLC, 27150 SW Kinsman Rd Wilsonville, OR 97070 USA. Made in China.

Canada (CA)

Customer Care Center: 416-792-6088

Email: customerservice@aosom.ca

Imported by Aosom Canada Inc., 7270 Woodbine Avenue, Unit 307, Markham, Ontario Canada L3R 4B9. Made in China.

France (FR)

Assistance Clientèle: 0033-1-84166106

Email: aosom@mhfrance.fr

Importé par/Fabricant/REP: MH FRANCE, 2 Rue Maurice Hartmann, 92130 Issy Les Moulineaux, France. Fabriqué en Chine.

Germany (DE)

Kundendienstzentrum: 0049-0(40)-88307530

Email: service@aosom.de

Hersteller/REP: MH Handel GmbH, Wendenstraße 309, D-20537 Hamburg, Germany. Hergestellt in China.

Italy (IT)

Centro Assistenza Clienti: 0039-0249471447

Email: clienti@aosom.it

Importato da/Produttore/REP: AOSOM Italy srl, Centro Direzionale Milanofiori, Strada 1 Palazzo F1, 20057 Assago (MI). Fatto in Cina.

Spain (ES)

Centro de Atención al Cliente: 0034-931294512

Email: atencioncliente@aosom.es

Importador/Fabricante/REP: SPANISH AOSOM, S.L., C/ROC GROS,N°15.08550, ELS HOSTALETS DE BALENYÀ, SPAIN. Hecho en China.

United Kingdom (UK)

Customer Care Center: 0044-800-240-4004

Email: enquiries@mhstar.co.uk

Importer Address: MH STAR UK LTD, Unit 27, Perivale Park, Horsenden lane South, Perivale, UB6 7RH. Made in China.

Portugal (PT)

Centro de Atendimento ao Cliente: 0034-931294512

Email: info@aosom.pt

Importador/Fabricante/REP: SPANISH AOSOM, S.L, C.ROC GROS N.15, 08550. ELS HOSTALETS DE BALENYÀ. Feito na China.

Please recycle packaging materials. [recycle symbol]