Outsunny 845-030 Series Storage Shed Assembly Manual

Important Information & Preparation

Important: Retain for future reference. Read carefully.

Before beginning construction, check local building codes regarding foundations, location, and other requirements. Study and understand this manual for important information and helpful tips for easier and more enjoyable assembly.

Assembly Instructions: Review all instructions and appropriate information before starting. Ensure you follow the step sequence carefully for successful results.

Foundation & Location

Choose a square and level area with good drainage for the storage building.

A strong plastic sheet (minimum 150µm thickness) should be placed under the foundation to help reduce rising dampness from the soil, thereby reducing condensation build-up in the shed. Your storage building must be anchored to prevent wind damage. Once secured, it is highly recommended to apply silicone along the inside of the base rail to minimize condensation.

Parts & Parts List

Before starting, separate and identify all parts and hardware to ensure you have all necessary components. Refer to the Parts List page for details.

If a part is missing, notify the seller within one week of receiving the product. Do not attempt assembly if parts are missing, as a partially assembled building can be seriously damaged by light winds.

Safety First

• Select a dry and calm day for assembly. Teamwork (two or more people) is required.
• Wear safety gloves ?, eye protection ?, and long sleeves during assembly to prevent injuries. Pay attention to sharp edges on some parts.
• Children and pets are not allowed on the construction site ?.
• Never concentrate your total weight on the roof of the building. When using a step ladder, ensure it is safe ?.

Care & Maintenance

• Keep the shed clean with a soft cloth; use water if necessary.
• Keep door tracks clear of dirt and debris to ensure smooth sliding.
• Remove snow with necessary tools to ensure safe entry. Heavy snow can cause collapse; ensure safety before entering.
• The shed is designed for storage, not for living.
• Apply oil to the top and bottom door sliding channels for smooth operation.

Dimensions & Installation Requirements

Area of Installation Requirement: 213 cm x 127 cm

Shed Dimensions:

• Height: 185 cm (overall), 152 cm (wall height)
• Width: 203 cm (front/back), 117 cm (side)
• Door Width: 96 cm

Note: The metal shed must be installed on a level wooden platform or a level concrete foundation. Screw Am-A42 can only be used for the wooden platform.

Parts List Overview

The parts list details numerous components categorized by assembly stage: UNDER, MIDDLE, TOP1, TOP2, DOOR, and ANNEX. Each part is identified by a number (e.g., Bs-A1, Bm-A7, Am-A40), includes a visual representation, dimensions (in mm), and quantity.

Assembly Steps

Follow these steps to assemble your Outsunny storage shed:

1. Step 01: Attach vertical pieces Bs-A1 and Bs-A2 to horizontal piece Am-A41 using four screws (Am-A41).
2. Step 02: Form a rectangular base by attaching vertical pieces Bs-A1 and Bs-A3 to horizontal pieces Bs-A2 and Bs-A3 using four screws (Am-A41).
3. Step 03: Continue forming the base frame by attaching vertical pieces Bs-A3, Bs-A4, and Bs-A5 to horizontal pieces Bs-A3 and Bs-A4 using four screws (Am-A41).
4. Step 04: Complete the base frame by attaching vertical pieces Bs-A4, Bs-A5, and Bs-A6 to horizontal pieces Bs-A4 and Bs-A5 using four screws (Am-A41).
5. Step 05: Attach side wall studs Bm-8 and Bm-A7 to the base frame using three screws (Am-A41) and one screw (Am-A43).
6. Step 06: Attach side wall studs Bm-8 and Bm-A7 to the base frame using three screws (Am-A41) and one screw (Am-A43).
7. Step 07: Attach side wall studs Bm-8 and Bm-A7 to the base frame using three screws (Am-A41) and one screw (Am-A43).
8. Step 08: Attach side wall studs Bm-8 and Bm-A7a to the base frame using two screws (Am-A41) and one screw (Am-A43).
9. Step 09: Attach corner studs As-A13 to the base frame using four screws (Am-A41).
10. Step 10: Assemble roof support beams Bs-A11 and Bs-A12 using two screws (Am-A41).
11. Step 11: Attach roof support beams Bs-A11 and Bs-A12 to the side walls using three screws (Am-A41).
12. Step 12: Attach roof purlins Bs-A9, Bs-A10 and supports T-P7, T-P2 using six screws (Am-A41).
13. Step 13: Attach roof purlins Bs-A9 and Bs-A10 to the structure using four screws (Am-A41).
14. Step 14: Attach roof purlins As-A13 and Bm-8 to the structure using twelve screws (Am-A41) and four screws (Am-A43).
15. Step 15: Attach roof purlins Bs-A11, Bs-A12, Bs-A1, and Bs-A2 to the structure using fourteen screws (Am-A41) and four screws (Am-A43).
16. Step 16: Attach roof purlins Bm-16, Bs-A9, and Bs-A4 to the structure using two screws (Am-A41) and one screw (Am-A43).
17. Step 17: Attach roof purlins Bm-17, Bs-A5, and Bs-A10 to the structure using two screws (Am-A41) and one screw (Am-A43).
18. Step 18: Attach roof purlins Bs-A4, Bs-A6, and Bs-A5 to the structure using four screws (Am-A41).
19. Step 19: Attach roof purlins Bs-A18, Bm-16, and Bm-17 to the structure using four screws (Am-A41).
20. Step 20: Attach roof panels As-A20, As-A19, Bs-A10, Bs-A9, and supports T-P8 using eight screws (Am-A41) and one screw (Am-A43).
21. Step 21: Attach roof panels As-A20, As-A19, Bs-A11, and Bs-A12 using nine screws (Am-A43).
22. Step 22: Attach roof panels As-A20, As-A19, T-A29, and T-A29a using eight screws (Am-A43).
23. Step 23: Attach roof beams As-A22, T-A29, and T-A29a using eight screws (Am-A43).
24. Step 24: Attach roof beams As-A22 using two screws (Am-A43).
25. Step 25: Attach roof beams As-A22, As-A20, and As-A19 using four screws (Am-A43).
26. Step 26: Attach roof beams Am-A23 and As-A19 using twelve screws (Am-A41).
27. Step 27: Attach roof beams Am-A23 and Am-A24 using twenty-four screws (Am-A41).
28. Step 28: Attach roof panels Am-A25, Am-A24, and Am-A23 using twelve screws (Am-A41).
29. Step 29: Attach roof panels Am-26 using six screws (Am-A41).
30. Step 30: Attach roof panels As-A38 and As-A39 using four screws (Am-A41).
31. Step 31: Attach roof panels As-A38, As-A39, and Am-A28 using ten screws (Am-A41).
32. Step 32: Attach roof panels T-P4 using two screws (Am-A41).
33. Step 33: Attach roof panels T-P3 using four screws (Am-A42).
34. Step 34: Attach roof panels TP5A, As-A19, and As-A20 using eight screws (Am-A41).
35. Step 35: (Diagram shows part Am-A42, likely a reinforcement or bracket).
36. Step 36: Attach base supports Am-A42 to the foundation using twelve screws (Am-A42).
37. Step 37: Shows parts for left (L) and right (R) side panels: Bm-31, Bm-A32, Bm-A30, Bs-A33, Bs-A34, Bm-A35, Bs-A36, Bs-A37.
38. Step 38: Assemble side panels (L & R) using eight screws (Am-A43).
39. Step 39: Assemble side panels (L & R) using eight screws (Am-A43).
40. Step 40: Assemble side panels (L & R) using two screws (Am-A41).
41. Step 41: Assemble side panels (L) using four screws (Am-A41).
42. Step 42: Assemble side panels (R) using four screws (Am-A41).
43. Step 43: Attach door hinges (T-P6) to door panels (Bm-A30, Bm-A35) using four screws (Am-A43).
44. Step 44: Assemble door frames (L & R) using four screws (Am-A43).
45. Step 45: Attach door components (T-P1, T-P2) to door frames.
46. Step 46: Attach door components (T-P2) to door frames using four screws (Am-A41).
47. Step 47: Shows various roof/support beams: V-A1, V-A2.
48. Step 48: Attach roof beams V-A1 using four screws (Am-A41).
49. Step 49: Attach roof beams V-A1 and V-A2 to the base frame using four screws (Am-A41).
50. Step 50: Final assembly of roof beams V-A1 and V-A2 to the structure using six screws (Am-A41).

Contact Information

If you have any questions, please contact the customer care center:

• US: 001-877-644-9366, customerservice@aosom.com (Imported by Aosom LLC)
• CA: 416-792-6088, customerservice@aosom.ca (Imported by Aosom Canada Inc.)
• DE: 0049-0(40)-87408465, service@aosom.de (MH Handel GmbH)
• IT: 0039-0249471447, clienti@aosom.it (AOSOM Italy srl)
• ES: 0034-931294512, atencioncliente@aosom.es (SPANISH AOSOM, S.L.)
• UK: 0044-800-240-4004, enquiries@mhstar.co.uk (MH STAR UK LTD)
• FR: 0033-1-84166106, aosom@mhfrance.fr (MH FRANCE)

Information on recycling is also available.