VIZIO VUR8 Universal Remote Control User Manual

1.1 VIZIO Universal Remote Control

The VIZIO Universal Remote Control is a versatile device capable of controlling up to four different electronic devices. Below are explanations of its primary buttons and their functions.

Remote Button Functions:

• Remote LED: This indicator blinks when the remote is operating.
• SET: Initiates all programming sequences for the remote control.
• POWER: Turns the connected device on from standby mode or returns it to standby mode.
• DVD: Selects a programmed DVD player.
• AUDIO: Selects a programmed Audio Receiver, Amplifier, or Home Theatre System.
• CABLE: Selects a programmed cable TV set-top box or satellite TV set-top box.
• TV: This button is pre-programmed to select codes for operating a VIZIO HDTV.
• 1 thru 0: Used for selecting channels or entering passwords.
• INPUT: Allows the user to cycle through available input sources.
• DASH [-]: Used in DTV mode to separate main and sub-channels (e.g., channel 28-2 is entered as 2 8 DASH 2).

Note: This is a programmable remote supporting up to 4 devices. If the remote is not functioning correctly with your VIZIO TV, pressing the TV button will reset the functions back to TV mode.

Additional Button Functions

• MENU: Accesses the On-Screen Display (OSD) menus.
• INFO: Displays image and system information.
• Navigation Wheel (with OK button): Used to navigate the OSD menus after activation via the MENU button. The OK button selects the chosen option.
• GUIDE: Displays program information; functional only for DTV.
• EXIT: Closes the On-Screen Display (OSD) menus.
• VOL (+ or -): Adjusts the volume up or down.
• LAST: Recalls the previously viewed channel.
• MUTE: Turns the sound on and off.
• CH (+ or -): Changes channels up or down.
• A, B, C, D: In CABLE mode, these buttons operate the Cable Box or Satellite Box, mirroring the functions of the original remote.
• TV: Selects TV Tuner input; cycles between TV and DTV inputs on Vizio models with dual tuners.
• AV: Cycles through AV1 and AV2 inputs.
• COMPONENT: Cycles through Component 1 and Component 2 inputs.
• HDMI: Cycles between HDMI 1 and HDMI 2 inputs (and up to HDMI 3 and 4 on some models).
• WIDE/RECORD: Cycles through available screen formats (Wide, Normal, Zoom, Panoramic). In RGB/PC and HDMI modes, options are 4:3 and 16:9. This button also initiates recording when controlling a Cable/Satellite Box or VCR.
• SLEEP/PAUSE: Allows setting a sleep timer in 30-minute increments up to 120 minutes. It also pauses playback when controlling a Cable/Satellite Box DVR, VCR, or DVD Player.
• MTS/PLAY: Selects MTS options (Stereo, SAP, Mono) in standard TV mode or alternate audio channels in DTV mode. It also starts playback for a Cable/Satellite Box DVR, VCR, or DVD Player.
• CC/STOP: Selects Closed Caption mode (options: OFF, CC1-CC4, TEXT1-TEXT4) or stops playback/recording.
• MODE/PREV: Selects the picture mode on a Vizio HDTV. It also skips to the previous chapter (DVR/DVD) or rewinds (VCR).
• FREEZE/REV: Freezes the current screen or displays live video. It also applies reverse play.
• AUDIO/FF: Switches audio in PIP/POP mode or applies fast play.
• SWAP/NEXT: Swaps inputs in PIP/POP mode or skips to the next chapter/fast forwards.

1.1.1 Insertion of Batteries in the Remote Control

Insert two AA batteries into the remote control, ensuring the (+) and (-) symbols on the batteries align with the corresponding symbols inside the battery compartment. Re-attach the battery cover.

Precautionary Tips for Inserting Batteries:

• Only use the specified AA batteries.
• Do not mix new and old batteries, as this may result in cracking or leakage, posing a fire risk or leading to personal injury.
• Incorrect battery insertion may also cause cracking or leakage, posing a fire risk or leading to personal injury.
• Dispose of batteries in accordance with local laws and regulations.
• Keep batteries away from children and pets.

1.1.2 Remote Control Range

Point the remote control at the remote control sensor to transmit commands. Avoid placing any obstacles between the remote control and the receiver window. The effective range is approximately 30 feet (10 meters) from the front of the receiver window, with a 30° range to the left and right, and a 20° range up and down.

1.1.3 VIZIO Remote Control Precautions

• Keep the remote control dry and away from heat sources; avoid humidity.
• If the TV responds erratically or not at all, check the batteries. Replace them with fresh batteries if they are low or exhausted.
• When not using the remote control for an extended period, remove the batteries.
• Do not attempt to disassemble, heat, or throw batteries into a fire.
• Do not subject the remote control to undue physical stress, such as striking or dropping it.
• Do not clean the remote control with volatile solvents; wipe it with a clean, damp cloth.

1.1.4 Cleaning the Housing and Remote Control

• Use the included VIZIO soft cloth for cleaning.
• If the housing or remote control is seriously contaminated, use a soft cloth moistened with diluted neutral cleaner. Wring out excess water before cleaning to prevent water from penetrating the housing. Wipe the display with a dry cloth after cleaning.

1.2 Programming the VIZIO Universal Remote Control

This remote control can be programmed to operate up to four different devices, including your VIZIO HDTV. The following steps guide you through programming your VCR, Cable Box, and DVD Player.

1.2.1 Programming for VCR

Note: The VIZIO Universal Remote Control does not have a dedicated "VCR" device button. You may program any of the available device buttons (such as DVD, AUDIO, or CABLE) to act as a VCR device selector if those devices are not in use.

1. Manually turn on the VCR.
2. Press the button on the remote control that you have selected to control the VCR.
3. Press and hold the SET button until the LED LIGHT flashes twice.
4. Find the programming code for your VCR in the code list and enter it using the Number Buttons. The LED will flash twice after the last digit is entered if the code is accepted.
5. If the LED does not flash twice, repeat Steps 2 through 4 with the next code listed for your VCR brand.
6. Point the remote control at the VCR and press the POWER button. The VCR should turn off.

Troubleshooting: If your VCR does not respond, try all available codes for your VCR brand. If codes do not work or your brand is not listed, refer to "Searching for Device Codes." Some listed codes may offer limited functionality; try other codes for more features.

1.2.2 Programming for Cable Set-Top Box

1. Manually turn on the Cable Box.
2. Press the CBL button on the remote control.
3. Press and hold the SET button until the LED LIGHT flashes twice.
4. Find the programming code for your Cable Box in the code list and enter it using the Number Buttons. The LED will flash twice after the last digit is entered if the code is accepted.
5. If the LED does not flash twice, repeat Steps 2 through 4 with the next code listed for your brand.
6. Point the remote control at the Cable Box and press the POWER button. The Cable Box should turn off.

Troubleshooting: If your Cable Set-Top Box does not respond, try all available codes for your brand. If codes do not work or your brand is not listed, refer to "Searching for Device Codes." Some listed codes may offer limited functionality; try other codes for more features.

1.2.3 Programming for DVD Player

1. Manually turn on the DVD Player.
2. Press the DVD button on the remote control.
3. Press and hold the SET button until the LED LIGHT flashes twice.
4. Find the programming code for your DVD player in the code list and enter it using the Number Buttons. The LED will flash twice after the last digit is entered if the code is accepted.
5. If the LED does not flash twice, repeat Steps 2 through 4 with the next code listed for your brand.
6. Point the remote control at the DVD Player and press the POWER button. The DVD Player should turn off.

Troubleshooting: If your DVD player does not respond, try all available codes for your brand. If codes do not work or your brand is not listed, refer to "Searching for Device Codes." Some listed codes may offer limited functionality; try other codes for more features.

1.2.4 Searching for Device Codes

If you cannot find your manufacturer in the device list or if the program code does not work, you can use the remote control's search function to find the correct device code.

1. Turn on the device you wish to control.
2. Press the matching device button on the remote control.
3. Press and hold the SET button until the LED flashes twice.
4. Press 9 9 1. The LED flashes twice to confirm.
5. Point the remote control at the device. Alternate pressing the POWER button and the device button on the remote control until the device turns off.

If the device still does not respond, clear the device button and repeat the search procedure.

1.2.5 Changing Volume Lock

The remote control can be configured to control volume through your TV while operating in Cable/Satellite, DVD, or VCR device modes.

1. Press and hold the SETUP button until the LED flashes twice.
2. Press 9 9 3. The LED flashes twice to confirm.
3. Press the device button for which you want to enable volume control. The LED flashes twice. The selected device's volume will now be controlled using the VOL+/- buttons.

2.0 Component Program Codes

This section contains extensive lists of setup codes for various brands of VCRs, Cable Converters, Satellite Receivers, DVD Players, CD Players, Audio Amplifiers, Audio Amp/Tuners, and TVs. These codes are crucial for programming the universal remote to operate your specific devices. Due to the large volume of codes, the complete lists are not reproduced here but are organized by device type and brand in the original document.

Key categories include:

• Setup Codes for VCR's
• Setup Codes for Cable Converters
• Setup Codes for Satellite Receivers
• Setup Codes for DVD Players
• Setup Codes for CD Players
• Setup Codes for Audio Amplifiers
• Setup Codes for Audio Amp/Tuners
• Setup Codes for TV's

Please refer to the original manual for the complete and detailed list of codes for each brand and device category.

3.0 Teaching Remote Control

This feature allows the VIZIO remote to learn commands from another remote control, effectively copying its functions.

3.1.1 Teaching the Remote

For optimal results, place the teaching and learning remote controls no farther than 2 inches apart. If the elapsed time between pressing keys exceeds 10 seconds, the remote control will exit programming mode, requiring you to restart from Step 1.

1. Press and hold down the SET key until the LED blinks twice.
2. Input code 9 7 5. The LED blinks twice to confirm code acceptance.
3. Press the Mode key (DVD, Audio, Cable, or TV).
4. Press the key you wish to learn; the LED will blink rapidly.
5. Press and hold the corresponding key on the teaching remote control.
6. The LED will stop blinking rapidly and then blink twice to confirm the key has been programmed.
7. Repeat Steps 3 through 6 until all desired keys are taught into your remote control.
8. Exit learning mode by pressing SET or by waiting 10 seconds (timeout).

3.1.2 Clearing Memory

To clear the remote's memory and reset it to its original factory codes:

1. Press and hold down the Set button until the LED blinks twice.
2. Input code 9 8 1. The LED blinks twice to signal code acceptance. (Alternatively, code 9 7 7 can be used instead).

The remote control is now ready to be programmed with original codes.