NETGEAR 8-Port Gigabit Ethernet Unmanaged Switch

Package Contents

• NETGEAR 8-port Gigabit Ethernet Unmanaged Switch (Model GS108X or GS108MX)
• Power adapter (power plug varies by region)
• Wall-mount installation kit
• Rubber feet
• Installation Guide

1. Register the Switch

1. Visit my.netgear.com from a computer or mobile device connected to the Internet.
2. Log in to your NETGEAR account. If you do not have an account, you can create one.
3. Click the REGISTER NEW PRODUCT button.
4. In the SERIAL NUMBER field, enter the 13-digit serial number found on the switch label.
5. Select the purchase date from the PURCHASE DATE menus.
6. Click the REGISTER button.

Your switch will be registered to your NETGEAR account, and a confirmation email will be sent.

2. Connect the Switch

Sample GS108X Connections

The GS108X connects computers, storage, servers, and other network devices. It features 8 Gigabit Ethernet ports and one 10G SFP+ port for high-speed uplinks. A typical setup might involve connecting computers to the Gigabit ports and a high-speed network backbone or server to the 10G SFP+ port. The diagram shows computers, servers, storage, and a WAX610PA device connected to the switch, with a connection to the Internet via a router and an XS508M with a 10G Fiber Link.

Sample GS108MX Connections

The GS108MX also connects computers, storage, servers, and other network devices, featuring 8 Gigabit Ethernet ports and one 10G/Multi-Gigabit port (supporting 10G/5G/2.5G/1G speeds). The diagram illustrates a similar network setup with computers, servers, storage, and a WAX610PA device, connected to the Internet via a router and an XS508M with a 10G Ethernet Link.

Cable Recommendations:

• For 10-Gigabit Ethernet connections: Use Category 6a (Cat 6a) cable or higher.
• For Gigabit Ethernet connections: Use Category 5e (Cat 5e) cable or higher.

Important Note: This switch is designed for indoor use only. If connecting to outdoor devices, ensure they are properly grounded and surge-protected. Install an inline Ethernet surge protector between the switch and any outdoor devices to prevent damage. For safety and warranty information regarding outdoor connections, refer to https://kb.netgear.com/000057103.

LED Indicators

Power LED

• On: Power is supplied to the switch.
• Off: Power is not supplied to the switch.

Gigabit Ethernet Port LEDs (Ports 1-8)

• Green (Solid): 1G link.
• Green (Blinking): 1G link with traffic activity.
• Yellow (Solid): 100M/10M link.
• Yellow (Blinking): 100M/10M link with traffic activity.
• Off: No link.

GS108X SFP+ LED (Port 9)

• Green (Solid): 10G link.
• Yellow (Solid): 1G link.
• Off: No link.

GS108MX Multi-Gigabit Ethernet LEDs (Port 9)

• Both Green LEDs Solid: 10G link.
• Both Green LEDs Blinking: 10G link with traffic activity.
• Left LED On, Right LED Off: 5G link.
• Left LED Blinking: 5G link with traffic activity.
• Left LED Off, Right LED On: 2.5G link.
• Right LED Blinking: 2.5G link with traffic activity.
• Both Yellow LEDs Solid: 1G link.
• Both Yellow LEDs Blinking: 1G link with traffic activity.
• Both LEDs Off: No link.

Mount the Switch on a Wall

Use the included wall-mount screws (0.12 in. diameter, 0.78 in. length).

1. Locate the two mounting slots on the bottom panel of the switch.
2. Mark and drill two holes 4.25 inches (108 mm) apart, center-to-center, in the desired wall location. Use a 3/16" (4.7mm) drill bit.
3. Ensure the switch is mounted horizontally with the ports facing downwards.
4. Insert the supplied anchors into the wall.
5. Tighten the screws with a No. 2 Phillips screwdriver, leaving approximately 0.15 inches (4 mm) of each screw protruding from the wall to align with the switch's mounting holes.
6. Position the switch over the screws, aligning the mounting holes, and slide it down until it is securely attached to the wall.

Technical Specifications

GS108X Supported Modules

Support and Community

For questions and the latest downloads, visit netgear.com/support.

For advice, visit the NETGEAR Community at community.netgear.com.

Regulatory and Legal

For Canadian customers, French documentation is available at netgear.com/support/download/.

For EU Declaration of Conformity and other regulatory compliance information, visit netgear.com/about/regulatory/. Review the regulatory compliance document before connecting the power supply.

NETGEAR's Privacy Policy is available at netgear.com/about/privacy-policy.

By using this device, you agree to NETGEAR's Terms and Conditions at netgear.com/about/terms-and-conditions. If you disagree, return the device within the return period.

Outdoor Use Warning: Do not use this device outdoors. For information on connecting outdoor cables or devices, see kb.netgear.com/000057103 for safety and warranty details.

6 GHz Devices: Use indoors only. Operation is prohibited on oil platforms, cars, trains, boats, and aircraft, except for permitted use in large aircraft above 10,000 feet. Operation in the 5.925-7.125 GHz band is prohibited for control or communication with unmanned aircraft systems.

Contact Information:

© NETGEAR, Inc. NETGEAR and the NETGEAR Logo are trademarks of NETGEAR, Inc. Non-NETGEAR trademarks are for reference only.