Introduction
This document provides comprehensive assembly instructions and safety guidelines for the JOOLA Outdoor TR table tennis table, identified by Article Numbers 11610 and 11611. Please read these instructions carefully before assembly and first use to ensure safe operation and proper maintenance.
JOOLA products are manufactured according to the latest safety regulations and undergo continuous quality control. This manual is intended for information, maintenance, and ordering spare parts. The table is made in Germany and printed on 100% recycled paper.
The table complies with safety standard EN 14468–1:2004.
Safety First
Intended Use: The table tennis table is designed solely for playing with suitable table tennis bats and balls. Any other use is prohibited and may be dangerous. The manufacturer is not liable for damage or injury resulting from improper use.
Component Integrity: Damaged or worn parts can compromise safety and the table's lifespan. Replace any damaged or worn components immediately and discontinue use until repairs are made. Use only genuine JOOLA spare parts.
Repairs and Modifications: The table complies with safety regulations. Improper repairs or modifications (e.g., removing original parts, adding unauthorized parts) can create hazards for the user.
User Awareness: Inform all users, especially children, about potential dangers, particularly during setup and takedown. Keep children away from the assembly area as small parts can be a choking hazard.
Assembly Precautions:
- Assembly requires two adults.
- Ensure a safe working environment, free from tripping hazards or misplaced tools.
- Dispose of packaging material safely. Plastic bags and films pose a suffocation risk to children.
- Be mindful of pinch points when folding and unfolding the table halves.
- When folded, the table presents a large surface area to the wind; store it in a sheltered location.
- The table should only be moved in its transport position to prevent injury.
- Regularly check all screws and bolts for tightness.
Handling and Maintenance
Pre-Use Check: Do not use the table until it is fully and correctly assembled and checked.
Weather Protection: Tables not designated as weatherproof must be kept away from moisture and dampness. Keep them away from direct heat sources. If table surfaces warp, lay them flat for a few days.
Setup: Always set up the table on a level surface.
Covering: Avoid using plastic covers that can cause condensation. A JOOLA weatherproof cover (Art. No. 7032-300) is recommended.
Solo Play: Each table half can be folded up individually for solo practice.
Cleaning: Use only environmentally friendly cleaning agents. Avoid aggressive or caustic substances. A slightly damp cloth is usually sufficient.
Disposal: JOOLA products are recyclable. Dispose of the product responsibly at the end of its life at an authorized collection point.
Assembly Steps Overview
Assembly involves several stages, requiring careful attention to detail and the correct use of provided hardware. The following is a summary of the key assembly actions:
- Frame Assembly: Construct the main leg frames and connect them using the specified screws and fasteners (e.g., M6x90, M6x40, washers). Ensure all connections are tightened securely.
- Wheel Attachment: Mount the wheel assemblies onto the leg frames using appropriate screws and washers.
- Support Structure: Attach lower frame supports and crossbars to the main leg structure for stability.
- Table Half Attachment: Secure the table halves to the assembled frame. This typically involves using brackets and screws. Ensure the table halves are properly aligned and cannot slip or tilt during this process.
- Final Securing: Install any remaining brackets or locking mechanisms as per the diagrams.
- Folding/Unfolding: Familiarize yourself with the mechanism for folding the table for storage and unfolding it for play. Pay attention to safety locks and pinch points.
Note: Always refer to the detailed diagrams provided in the original manual for precise hardware usage and step-by-step guidance.
Tools Required (Not Included)
The following tools are recommended for assembly:
- Wrench (size SW 5 indicated)
- Measuring tape (for reference)
- Screwdriver (type not specified, but implied by diagrams)
Spare Parts
When ordering spare parts, always provide the full article number, the specific spare part number, the required quantity, and the product's serial number. Refer to the spare parts list and drawing for identification.
Key components include:
- Table Top (TT-Platte)
- Frame Profiles (Profil)
- Corner Connectors (Eckverbinder)
- Locking Mechanisms (Verriegelung)
- Table Wheels (TT-Rad)
- Various screws, nuts, and washers.
Note: Spare parts prices typically do not include fastening material. If fastening material is required, it must be explicitly requested when ordering.
Spare Parts Drawing and List
A detailed diagram (page 23) illustrates the location of each numbered spare part, corresponding to the list provided on page 22. This list includes part numbers, descriptions, quantities, and article numbers for reference.
