IKEA PAX Wardrobe Assembly Instructions

Important Safety Information

WARNING! This product must be mounted to the wall to complete the assembly. Serious or fatal crushing injuries can occur if the product is not mounted according to assembly instructions.

Different wall materials require different types of fixing hardware. Use fixing hardware suitable for the walls in your home. Included screws and plugs are suitable for most common walls. If you are uncertain, seek professional advice.

French: ATTENTION! Ce produit doit être fixé au mur pour terminer l'installation. Risque de blessure grave ou mortelle si le produit n'est pas fixé comme indiqué dans les instructions de montage. Le choix des fixations dépend du matériau du mur dans lequel elles doivent être fixées. Toujours utiliser des fixations adaptées aux murs de votre logement. Les vis et chevilles incluses sont adaptées à la plupart des murs standard. En cas de doute, demander conseil à un vendeur spécialisé.

Spanish: ADVERTENCIA: Este producto se debe instalar en la pared para completar el montaje. Si el producto no se monta de acuerdo con las instrucciones de montaje, pueden ocurrir lesiones graves e incluso mortales. El tipo de fijación depende del tipo de pared. Utiliza siempre las fijaciones adecuadas para las paredes de tu hogar. Los tornillos y tacos que incluye se adaptan a la mayoría de paredes. En caso de duda, consulta a un profesional.

Tools Required

The following tools are typically needed for assembly:

• Screwdriver (Phillips and flathead)
• Spirit level
• Ladder
• Measuring tape
• Saw (for potential adjustments)
• Drill with drill bits (Ø 5/16" (8 mm) and Ø 1/8" (3 mm))

Assembly Steps

Follow the numbered steps carefully. Ensure all parts are correctly identified before starting.

Step 1: Identify Parts and Prepare

The first step involves identifying all the components provided in the package. Refer to the diagrams for part numbers and quantities.

Step 2: Wall Mounting Preparation

Determine the correct placement for the wardrobe and mark the wall for drilling. Ensure the wall is suitable for mounting furniture.

Diagram Description: Illustrates marking the wall for drilling, showing measurements like 2 1/2" (6.3 cm) and 7 5/8" (19.3 cm) from edges or other points.

Step 3: Drilling and Wall Anchoring

Drill holes in the wall according to the marked positions. Insert appropriate wall anchors (screws and plugs are provided for most common walls). Three methods (A, B, C) are shown for different wall types:

• Method A: Uses Ø 5/16" (8 mm) drill bit and specific anchors.
• Method B: Uses Ø 5/16" (8 mm) drill bit and angled anchors, with a depth of approximately 1 1/4" (30 mm).
• Method C: Uses Ø 1/8" (3 mm) drill bit and different anchors, with a depth of approximately 1 1/4" (30 mm).

Step 4: Attaching Mounting Brackets

Attach the mounting brackets to the wall using the provided screws. Ensure they are level and securely fastened.

Diagram Description: Shows attaching a bracket to the wall with screws (part 109571) and anchors (part 108817).

Step 5: Assembling the Wardrobe Frame

Assemble the main frame of the wardrobe. This typically involves connecting side panels, top, and bottom panels.

Diagram Description: Two people are shown lifting and aligning the wardrobe panels. Warning symbols indicate caution during lifting and assembly.

Step 6: Securing the Frame

Connect the assembled frame to the wall using the previously installed brackets. Ensure a secure fit.

Diagram Description: Shows the wardrobe frame being attached to the wall brackets, with arrows indicating the direction of connection. A close-up shows how to secure the frame to the bracket.

Step 7 & 8: Folding and Positioning

The wardrobe may have folding elements or doors that need to be positioned correctly.

Diagram Description: Shows two people positioning the wardrobe, and then folding or adjusting sections of it.

Step 9: Installing Internal Components

Install any shelves, drawers, or hanging rails as per the design.

Diagram Description: Shows how to attach internal support brackets (part 10042549) to the wardrobe interior, with a rotational action indicated.

Step 10: Attaching Sliding Mechanisms

Install the sliding mechanisms for doors or drawers.

Diagram Description: Shows attaching a sliding component (part 10042526) to the wardrobe frame.

Step 11 & 12: Securing Internal Shelves/Supports

Secure internal shelves or support structures.

Diagram Description: Shows securing internal components with brackets and screws.

Step 13 & 14: Attaching Door Hinges/Runners

Attach the necessary hardware for the sliding doors.

Diagram Description: Shows attaching door runners (parts 10120505, 10046278) to the wardrobe frame.

Step 15: Installing Doors

Mount the sliding doors onto the runners.

Diagram Description: Shows the doors being placed onto the runners. A close-up shows how to attach the doors, possibly with a click mechanism.

Step 16: Adjusting Doors

Adjust the doors for proper alignment and smooth operation.

Diagram Description: Shows adjusting the doors using screws, with indicators for minimum clearance (e.g., Min 1/16" (2 mm)).

Step 17: Final Wall Securing

Ensure the wardrobe is securely fastened to the wall at multiple points.

Diagram Description: Shows attaching brackets (parts 10115992, 10115994, 10115937, 10115938, 10115993) to the top of the wardrobe and then securing them to the wall. Warning symbols indicate the importance of secure mounting.

Step 18: Door Alignment Check

Perform a final check on door alignment and operation.

Diagram Description: Shows sliding the doors and checking their alignment.

Step 19: Adjusting Base Level

Adjust the base of the wardrobe to ensure it is level on the floor.

Diagram Description: Shows adjusting leveling feet or the base structure using a tool (part 101349).

Step 20: Securing Top Panel

Secure the top panel of the wardrobe.

Diagram Description: Shows attaching a component to the top of the wardrobe using screws (part 110438).

Step 21 & 22: Final Door Attachments

Complete the attachment of the doors, ensuring they slide smoothly.

Diagram Description: Shows final adjustments and securing of the doors, possibly involving locking mechanisms (parts 10050446, 10115991, 10116990).

Step 23: Final Stability Check

Ensure the entire unit is stable and securely mounted to the wall.

Diagram Description: Shows the completed wardrobe, with a ladder used for reaching higher parts during assembly. Mentions parts 10042543, 10046300, 10046304.

Step 24: Attaching Top Support

Attach any final top support or decorative elements.

Diagram Description: Shows attaching components to the top of the wardrobe, possibly with a "STOP" indicator for a specific action.

Step 25: Final Door Securing

Final securing of the doors.

Diagram Description: Shows a final step for securing the doors, possibly involving a locking mechanism.

Step 26 & 27: Final Adjustments

Make any final adjustments to the doors or internal components.

Diagram Description: Shows final adjustments to the door runners and internal mechanisms.

Step 28: Identifying Left and Right Components

Ensure correct identification of left (L) and right (R) components for the doors or internal fittings.

Diagram Description: Shows how to identify and attach left and right door runners (parts 10115941, 10115998, 10116001 for left; 10116003, 10115999, 10116002 for right).

Step 29: Installing Shelves

Install any remaining shelves.

Diagram Description: Shows a shelf being inserted into the wardrobe.

Step 30: Final Check

Perform a final check of all assembled parts and ensure the wardrobe is stable and secure.

Diagram Description: Shows final checks and adjustments, possibly involving a screwdriver (part 10094315).

Dimensions

The PAX system is available in various dimensions. Examples shown include:

• 19 5/8" x 92 7/8" (50 cm x 236 cm)
• 29 1/2" x 92 7/8" (75 cm x 236 cm)
• 39 3/8" x 92 7/8" (100 cm x 236 cm)
• 19 5/8" x 79 1/8" (50 cm x 201 cm)
• 29 1/2" x 79 1/8" (75 cm x 201 cm)
• 39 3/8" x 79 1/8" (100 cm x 201 cm)

Detailed measurements for each configuration are provided in the diagrams.