Costway Loft Bed with Slide HW64315

User's Manual

Important Safety Information

Please read and keep this instruction booklet for future reference. It contains important safety information.

Contact Information: If you have any issues, please contact the Costway customer service department first. Replacements for missing or damaged parts will be shipped ASAP.

Assembly Note: This bed should be assembled by 2 adults. The floor area is approximately 2m x 2m.

Follow Costway on social media: [Facebook] [Twitter] [YouTube] [Instagram]

Before You Start

Read each step carefully before starting. Ensure steps are followed in the correct order to avoid assembly difficulties.
Check that all parts are included. Most board parts are labeled or stamped on the raw edges.
Work in a spacious area, preferably on a carpet near where the unit will be used.
Keep hand tools close at hand. Do not use power tools to assemble the furniture, as they may scratch or damage the parts.

Hardware is included inside.

Care and Maintenance

Use a soft, clean cloth that will not scratch the surface when dusting.
Furniture polish is not necessary. If you choose to use polish, test it first in an inconspicuous area.
Using solvents of any kind may damage the finish.
Never use water to clean the furniture, as it may cause damage to the finish.
Liquid spills should be removed immediately. Use a soft, clean cloth to blot the spill gently. Avoid rubbing.
Check bolts/screws periodically and tighten them if necessary.

Further advice about wood furniture care:

Keep furniture in a climate-controlled environment. Extreme temperature and humidity changes can cause fading, warping, shrinking, and splitting of wood.
Keep furniture away from direct sunlight, as sun may damage the finish.
Proper care and cleaning will extend the life of your purchase.

Part List

A: Horizontal HB & FB x 6
B: Leg (Left Front) x 1
C: Leg (Left Back) x 1
D: Leg (Right Front) x 1
E: Leg (Right Back) x 1
F: Side rail (Back) x 1
G: Long guard rail x 2
H: Side rail (Front) x 1
I: Short guard rail x 2
J: Vertical guard rail x 1
K: Front guard rail support x 1
L: Ladder x 1
M: Step ladder x 2
N: Left side slide x 1
O: Right side slide x 1
P: Slide panel x 1
Q: Slide base support x 1
R: Slat x 8

Hardware List

1: Wood dowel Ø10*40mm x 6
2: Wood dowel Ø10*30mm x 2
3: Hex-Head bolts (Ø15)1/4"*100mm x 12
4: Hex-Head bolts (Ø15)1/4"*80mm x 16
5: Hex-Head bolts (Ø12)1/4"*70mm x 4
6: Hex-Head bolts (Ø12)1/4"*35mm x 5
7: Hex-Head bolts (Ø12)1/4"*30mm x 3
8: Horizontal-Hole bolts 1/4"*15mm (9.5mm) x 32
9: Hex-Head bolts (Ø12)1/4"*50mm x 12
10: Wood screws Ø4*30mm x 20
11: Hooks 142*18*2mm x 2
12: Allen Key (1/4")4.5*58mm x 1
13: Wood screws Ø4*38mm x 2
14: Plastic anchor Ø9*32mm x 2
15: Metal bracket 58*16*16*(1.5mm) x 2
16: Wood screws Ø4*25mm x 4

Assembly Steps

Step 1:

Attach parts A, B, C, D, E, F, G, H, I, J, K, L, M, N, O, P, Q, R using hardware 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16 as shown in the diagrams. Note: Part 8 will face up with the "x" mark on it, otherwise it cannot be tightened.