Costway HU10769 Twin Loft Bed

Introduction and Contact Information

This instruction booklet contains important safety information. Please read and keep for future reference.

If you are experiencing difficulties, the customer team is available to assist. Contact information for various regions is provided:

• USA: cs.us@costway.com
• AUS: cs.au@costway.com
• GBR: cs.uk@costway.com
• FRA: cs.fr@costway.com

Offices are located in Fontana (USA), Truganina (AUS), Saint Vigor d'Ymonville (FRA), and Great Blakenham, Ipswich (GBR).

Safety Warnings

Before You Start

• Please read all instructions carefully.
• Retain instructions for future reference.
• Separate and count all parts and hardware.
• Read through each step carefully and follow the proper order.
• We recommend assembling the product near its intended use area to avoid unnecessary movement once assembled.
• Always place the product on a flat, steady, and stable surface.
• Keep all small parts and packaging materials away from babies and children, as they can pose a choking hazard.

General Safety Warnings

• This bed is designed for use only with mattresses meeting specific size requirements for the upper and lower bunks (Twin Standard).
• Follow information on warnings affixed to the bed structure and carton. Do not remove warning labels.
• Always use recommended size mattresses or supports to prevent entrapment or falls.
• The mattress surface must be at least 5" (127mm) below the upper edge of guardrails.
• Do not allow children under 6 years of age to use the upper bunk.
• Periodically check that guardrails, ladder, and other components are in proper position, undamaged, and that all connectors are tight.
• Do not allow horseplay on or under the bed and prohibit jumping on the bed.
• Always use the ladder for entering and leaving the upper bunk.
• Do not use substitute parts. Contact customer service for questions.
• Use of a night light may provide added safety for a child using the upper bunk.
• Always use guardrails on both long sides of the upper bunk. If placed next to a wall, the guardrail running the full length should be against the wall to prevent entrapment.
• The use of water or sleep flotation mattresses is prohibited.
• STRANGULATION HAZARD: Never attach or hang items not designed for the bed (e.g., hooks, belts, jump ropes) to any part of the bunk bed.
• Keep these instructions for future reference.
• Prohibit more than one person on the upper bunk.
• It is recommended to assemble the bunk bed on the shipping carton to protect your floor or carpet.
• Ensure all staples are removed from the box before beginning assembly on the shipping carton.

Return and Damage Claim Instructions

• DO NOT discard the box / original packaging. In case of return, the item must be in its original box; otherwise, the return will not be accepted.
• Take a photo of the box markings. A photo of the text markings on the side of the box is required if a replacement part is needed. This helps identify the product number for correct parts.
• Take a photo of the damaged part (if applicable). A photo of the damage is always required to file a claim and process replacements or refunds quickly. Ensure you have the box, even if damaged.
• Send an email with the images requested. Email directly from the marketplace where the item was purchased, attaching images and a description of your claim.

Part List

The following parts are included in the package:

Hardware List

The following hardware pieces are included:

Assembly Instructions

Follow these steps carefully to assemble your Twin Loft Bed.

Note: It is recommended to assemble the bed on the shipping carton to protect your floor or carpet.

Step 1

Assemble the side frame. Attach horizontal bars (part 4) to the inner side of side panels (parts A1, A2, A3). Use 4 bolts (part 9) for each connection. Ensure part 9 is oriented with the "x" mark facing upwards for proper tightening, as indicated in the diagram.

Step 2

Assemble the main bed frame. Connect side panels (parts A1, A2, A3) with horizontal bars (part 4) and vertical supports (parts B1, B2, B3, B4, B5, B6). Use bolts (parts 5 and 9) as shown in the diagram. The diagram shows the base structure being formed with multiple connection points.

Step 3

Continue assembling the base structure. Attach additional horizontal and vertical supports (parts B1, B2, B3, B4, B5, B6) to the frame. Secure these parts using bolts (parts 8 and 10) at the indicated locations.

Step 4

Assemble the upper bunk frame. Connect side panels (parts A1, A2, A3) with horizontal bars (part 4) and vertical supports (part 3). Use bolts (parts 1 and 9) for these connections. The diagram illustrates the construction of the upper section of the bed frame.

Step 5

Attach guardrails and other structural elements to the upper bunk frame. Secure these components using bolts (part 8) at the designated points. This step reinforces the upper bunk structure.

Step 6

Attach the bed slats (part F) to the upper bunk frame. Use screws (parts 1, 3, 7, and 9) to secure the slats in place. The diagram shows the placement of multiple slats across the frame.

Step 7

Install the LED lighting system. Connect the LED light strip (part 15) to the adapter and wire strip (part 17). The remote control (part 18) is also shown. The diagram illustrates how the light strip is routed and connected.

Step 8

Assemble and attach the ladder and guardrail components. Connect ladder parts and guardrails (parts 2, 6, 9, 10) to the main frame using the specified hardware. The diagram shows multiple connection points for these safety features.

Step 9

Continue assembling the ladder and guardrail system. Connect additional panels and supports (parts 2, 6, 9) to further build out the ladder structure and secure guardrails. The diagram shows detailed connections for these elements.

Step 10

Attach the remaining horizontal bars (part 11) and shelf panels (parts H4, H5, H6) to the structure. Use bolts (part 11) to secure these components. The diagram shows the placement of these parts to form shelves and complete the frame.

Step 11

Assemble the shelving units or storage compartments. Connect various panels (parts J, K, L) using screws (part 13) as shown in the diagram. This step forms the individual storage modules.

Step 12

Attach the assembled shelving units to the main bed frame. The diagram shows arrows indicating the direction of attachment for the shelving modules to the bed structure.

Step 13

Attach guardrails (part 6) to the lower bunk structure. Use bolts (part 6) to secure these safety rails. The diagram shows the placement of guardrails on the lower section of the bed.

Step 14

Attach bed slats (part 12) to the side rails. NOTE: Please make sure the bed slats are close to the side rail before locking the screws to avoid breakage. This step is required for both the left and right sides. Do not lock the screws of the bed slats at the outermost edge to avoid damaging them. The diagram shows a close-up of the slat attachment with a checkmark for correct placement and a cross for incorrect placement.

Step 15

The final assembly is shown, depicting the complete Twin Loft Bed with all components attached, including the shelving units, ladder, guardrails, and the LED lighting system. The diagram illustrates the fully assembled product.

Exploded View

The exploded view provides a comprehensive visual breakdown of all components of the Twin Loft Bed. It displays the main bed frame pieces, including side panels, horizontal and vertical bars, guardrails, ladder steps, and shelving units, along with various hardware pieces. The diagram illustrates how these parts are intended to connect to form the complete structure, serving as a guide to understand the overall assembly.