SOMiC G810 Wireless Gaming Headset

Product Specifications

Product Features

• Supports stereo music playback, play/pause, volume control, track selection, and microphone mute/unmute.
• Supports common telephone functions: answer, end, reject, and redial last number.
• Provides voice prompts for operations and low battery status.
• Supports HFP1.7, HSP1.2, A2DP1.3, AVRCP1.6 profiles.
• Supports AAC and SBC audio decoding.
• Features low-latency gaming mode via Dongle connection.

Key and Socket Definition

The diagram illustrates the SOMiC G810 headset, highlighting its ergonomic design. Key components and interfaces are labeled:

• Left and Right Ear Shells: Houses audio drivers and controls.
• Headband: Adjustable for comfortable fit.
• Buttons:
• ① Volume + / Next Track Key
• ② Volume - / Previous Track Key
• ③ Multifunction Key (MFB) for power, pairing, play/pause, and call handling.
• ④ Light Switch Button to toggle logo lighting.
• ⑤ Mic Key / Sound Effect Mode Switch Key for microphone mute and switching between Game/Music modes.
• Sockets:
• ⑦ Line In 3.5mm Audio Input Interface for wired connection.
• ⑧ Type C Charging Interface for charging the headset.
• Indicators:
• ⑥ Bluetooth Indicator Window displays connection status (pairing, connected, incoming call, low battery).
• ⑨ Charging Status Indication Window shows charging progress (red for charging, green for fully charged).
• ⑩ Left and Right Ear Shell Lights provide visual effects.

Basic Operation Instructions

1. Power On & Pairing

To power on, long-press the MFB (③) for about 2 seconds. For pairing, long-press the MFB (③) for about 6 seconds from a powered-off state until the indicator flashes red and blue alternately. Connect via your device's Bluetooth settings, searching for "SOMiC G810". Upon successful connection, a "Connected" voice prompt is given, and the indicator light will flash slowly blue. The included Bluetooth transmitter (Dongle) is pre-paired; simply plug it into a USB port for automatic connection.

2. Power Off

When the headset is on, long-press the MFB (③) for about 3 seconds. A "Power off" prompt will sound.

3. Volume Up / Next Track

Short-press the Volume + key (①) to increase volume. Long-press the Volume + key (①) to skip to the next track.

4. Volume Down / Previous Track

Short-press the Volume - key (②) to decrease volume. Long-press the Volume - key (②) to go to the previous track.

5. Mute MIC / Mode Switch

During a call or use, short-press the Mic key (⑤) to mute/unmute the microphone (voice prompts "MIC OFF" / "MIC ON"). Long-press the Mic key (⑤) for 2 seconds to switch between "Game Mode" and "Music Mode" (indicated by voice prompts).

6. Light Button

Briefly press the Light Switch button (④) to turn the logo lighting effect on or off.

7. Calls

When there is an incoming call, a "Incoming call" prompt will sound, and the blue indicator light will flash quickly. Short-press the MFB (③) once to answer the call. Short-press the MFB (③) again to end the call. Long-press the MFB (③) for 1 second to reject the call.

8. Last Number Redial

While connected to a phone, double-press the MFB (③) to redial the last dialed number.

9. Low Power Warning

When the battery is low, a "Low Power" voice prompt will occur every 4 minutes, and the red indicator light will flash twice every 3 seconds.

10. Charging Instructions

Connect the Type C charging cable to the headset's Type C port (⑧). The headset will automatically shut down during charging. The charging indicator (⑨) will be solid red while charging and turn solid green when fully charged. It is recommended to charge the headset before first use.

11. Bluetooth Transmitter Instructions

The Bluetooth transmitter (Dongle) is factory-paired with the headset. Connect the Dongle to a computer or mobile device's USB port (or via the extension cable). The headset will automatically connect upon powering on.

12. Headset Factory Reset

To restore factory settings, with the headset powered off, long-press both the Volume + (①) and MFB (③) buttons simultaneously for 10 seconds. A "beep" sound will confirm completion, and the indicator lights will flash blue and red three times. This action clears all previous pairing information.

13. Wired Mode

Connect a 3.5mm audio cable to the Line In interface (⑦). In this mode, only the microphone on the audio cable can be used; the headset's built-in microphone is disabled.

Headset and Accessories

Using Statement

• Do not use the headphones while charging.
• When wearing headphones outdoors, select safe venues and roads, adjust volume appropriately, and pay attention to traffic safety.
• Do not use headphones while driving a motor vehicle.

After-sales Service

Before sending the product for repair, please check the following items to save your time.

Reminder

• Please read this user manual carefully and keep it for future reference.
• Charge the product before first use.
• To maintain battery health, use the product at least once every two weeks and recharge promptly after use.
• Use only chargers from reputable manufacturers certified by CCC.
• If your mobile phone cannot find the Bluetooth headset, ensure the headset is in pairing mode. If it hasn't paired or connected for a long time, restart the headset or perform a factory reset.

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.