DRIJA Quadrato Isla 90 Range Hood User Manual
Model: Quadrato Isla 90
Brand: DRIJA
Table of Contents
Safety Warnings
Never let children operate the machine.
The cooker hood is for home use only, not suitable for barbecue, roast shop, and other commercial purposes.
The cooker hood and its filter should be cleaned regularly to maintain good working condition.
Clean the cooker hood according to the instruction manual and keep the unit from danger of burning. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard.
Forbid direct baking from the gas cooker.
Please keep the kitchen with good convection.
Before connecting this appliance, check that the power supply cord is not damaged. A damaged supply cord must be replaced by qualified service personnel only. There is a fire risk if cleaning is not carried out in accordance with the instructions.
There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels.
The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.
Regulations concerning the discharge of air have to be fulfilled.
This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Do not flambe under the range hood.
The range hood is not intended to be installed over a hob having more than four hob elements.
Electrical Shock Hazard: Only plug this unit into a properly earthed outlet. If in doubt, seek advice from a suitably qualified engineer. Failure to follow these instructions can result in death, fire, or electrical shock.
CAUTION: Accessible parts may become hot when used with cooking appliances.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
When the range hood and appliances supplied with energy other than electricity are simultaneously in operation, the negative pressure in the room must not exceed 4 Pa (4x 10-5 bar).
Notice
Thank you for choosing our cooker hood. Please read the instruction manual carefully before use.
The installation work must be undertaken by a qualified and competent fitter.
The manufacturer disclaims all liability for any damage or injury caused as a result of not following instructions for installation contained in the following text.
The range hood is used on 110V / 60Hz.
Features
The cooker hood uses high quality materials and is made with a streamlined design.
Equipped with a large power, low noise electric motor and centrifugal leaf, it produces strong suction, low noise, has a non-stick grease filter, and is easy to clean.
With the isolated low voltage circuit board control and 12V DC input, the lights are therefore safer.
Special wind tunnel construction and oil collector design; free dirt will be absorbed in a second.
Installation
Product Type: Island
Ensure the installation position, fix the hanging scaffold in the appropriate position, and check the firmness and smoothness of the installation. See Pic 1.
Pic 1 Description: Illustrates the recommended installation height of 65cm to 75cm (26-30 inches) from the cooking surface to the bottom of the hood. It shows the main hood body and chimney parts.
Adjust the support connection to the hanging scaffold to the appropriate height. See Pic 2.
Pic 2 Description: Shows the interior chimney bracket and the interior chimney.
Fix the inner chimney to the hanging scaffold, place the outer chimney in the appropriate position, and insert the hook into the support to temporarily fix the outer chimney. See Pic 3.
Pic 3 Description: Shows the exterior chimney bracket and the exterior chimney.
Fix the air outlet to the hood body's vent and connect the extensible tube to the air outlet. See Pic 4.
Pic 4 Description: Shows a screw and washer assembly (E-M16, 8-18x47, 8-18x50).
Extend the hose outside the hanging scaffold and fix the hood body to the support. See Pic 5.
Pic 5 Description: Shows the final assembly with the chimney secured by a safety screw.
Unfasten the hook, move the outer chimney downwards until it reaches the hood body. Be careful not to hit the glass. See Pic 6.
Pic 6 Description: Shows the assembled chimney parts.
Note: The two safety vents are positioned on the back casing, with a diameter of 6mm.
Installation Notice:
- Before installation, please ensure the area is clean to avoid suction of remaining bits of broken wood and dust.
- It cannot share the same air ventilation tube with other appliances such as gas tubes, warmer tubes, and hot wind tubes.
- The bending of the ventilation tube should be ≥120°, parallel or above the start point, and should be connected to the external wall.
- After installation, make sure that the extractor is level to avoid grease collection at one end.
Diagram Description (Right/Wrong): Shows two diagrams illustrating correct and incorrect ventilation tube installation; the "Wrong" one shows a sharp bend, while the "Right" one shows a smoother, compliant bend.
Use (Speed Adjustment)
Touch Control Switch:
- ⏰ Timer, which can be set from one minute to 60 minutes.
- ? Light on/off.
- + Speed increases from low to medium, and to high sequentially.
- - Speed decreases sequentially from high to medium, and to low until the power stops running.
Touch Switch:
- (1) Illumination changes from Red/Yellow/Blue based on speed adjustment.
- (2) White color illumination is constant while operating.
Functions:
- Press the button for two seconds, the motor starts operating at low speed and the lighting turns on.
- Press the button softly again, it switches to medium speed and the lighting turns on.
- Press once again, it switches to high speed and the lighting is on.
- If pressed again, it will switch to the low speed and cycle through the previous conditions.
- For any condition of operating, press for two seconds, it will be power-off.
Maintenance
1. The cleaning of the carbon grease filter mesh:
The filter mesh is made of high-density stainless steel. Please do not use corrosive detergent on it. Keeping this filter clean will keep the appliance running correctly. Please strictly follow the guidelines below.
- Method 1: Put the mesh into 40-50°C clean water, pour on detergent, and soak for 2-3 minutes. Wear gloves and clean with a soft brush. Please do not apply too much pressure, as the mesh is delicate and will damage easily.
- Method 2: If instructed to do so, it can be put into a dishwasher, set the temperature at around 60 degrees.
2. Notice of cleaning cooker hood:
- A. To protect the main body from corrosion over a long period, the cooker hood should be cleaned with hot water plus non-corrosive detergent every two months.
- B. Please do not use abrasive detergent or deodorant as it will damage the body.
- C. Keep the motor and other parts free from water, as this will cause damage to the appliance.
- D. Before cleaning the appliance, please remember to cut off power.
- E. The carbon filter should not be exposed to heat.
- F. Please do not tear open the fixed bar around the carbon filter.
- G. If the plug or cord is damaged, please replace it with a special soft cord.
- H. Cleaning and maintenance should not be carried out by children without supervision.
Abnormity and Solution
| Fault | Cause | Solution |
|---|---|---|
| Light on, but motor not working | The leaf blocked | Clear the blockage. |
| The capacitor damaged | Replace capacitor. | |
| The motor jammed bearing damaged | Replace motor. | |
| The internal with of motor off or a bad smell from the motor | Replace motor. | |
| Light does not work, motor does not work | Light damaged | Replace lights. |
| Power cord loose | Connect the wires as per the electric diagram. | |
| Oil leakage | One way valve and the air ventilation entrance are not tightly sealed | Dismantle the one way valve and seal with glue. |
| Leakage from the connection of U-shaped section and cover | Take down the U-shaped section and seal with soap or paint. | |
| Shake of the body | The leaf damaged and causes tremors | Replace the leaf. |
| The motor is not tightly hanged | Lock the motor tightly. | |
| The body is not tightly hanged | Fix the body tightly. | |
| Insufficient suction | The body is not tightly hanged | Readjust the distance. |
| Too much ventilation from open doors or windows | Choose a new place and reassemble the machine. | |
| The machine inclines | The fixing screw not tight enough | Tighten the hanging screw and make it horizontal. |
| The hanging screw not tight enough | Tighten the hanging screw and make it horizontal. |
Warranty Card
We warrant this product free from defects in material and quality for one year from the date of purchase. If any problems occur from correct usage, please contact the service department for under-warranty service.
This warranty does not cover the following:
- The filter mesh and bulb.
- Commercial use.
- Amendment of the date of manufacture on the rating plate.
- After 12 months from date of purchase.
- Damage caused to the body by usage of detergent sprayer.
- Pollution made to the LED parts, glass parts, and stainless steel parts.
- Incorrect installation, misuse, abuse, or neglect.
- Incorrectly fitted to insufficient or unsuitable power.
- Damage caused by foreign object.
- Taken apart or serviced by unauthorized service engineers or replaced with other manufacturer's components.
For commercial use, maintenance and free service should be discussed with our authorized agent.
Beyond the 12-month warranty period, the purchaser should pay for charges of components and call-out.
In the event of a service call, please provide the warranty card and receipt of date of purchase.
Place of purchase: ____________________
Date of purchase: ____________________
Model: ____________________
Shop stamp: ____________________
Environmental Protection
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
[WEEE recycling symbol]
Diagram Description: The diagram shows a crossed-out wheeled bin, indicating that the product should not be disposed of with regular household waste.
Product Diagram and Dimensions
Diagram Description: An illustration shows the range hood with its chimney. Key dimensions are indicated: 118 cm (height), 90 cm (width of the hood base), and 28.6 cm (width of the chimney). It also notes "Olores Filtrados / Filtered Odors".
Installation Requirement for Warranty: To keep the warranty, you must install the hood at a minimum of 76 cm from the cooktop.
