User Manual
6" LED Recessed Black Slim Selectable Downlight w/ Night Light
SKU: CL_SL6_NL-BK-2760K
Contact Sunco Support: support@sunco.com | (844) 334-9938
Certifications: ETL Listed (Intertek), FCC Compliant, RoHS Compliant
What's in the Box?
Slim Downlight Components:
- Light Fixture (A) x1: A circular LED panel with spring clips and an integrated junction box.
- Junction Box (B) x1: A small, rectangular electrical box with knockouts for cable entry and a hinged lid.
- Installation Template (C) x1: A circular paper template with a cutout indicating the required hole size.
- Wire Nuts (D) x3: Three small plastic connectors used to join electrical wires.
Tools/Gear Not Included:
- Cable Connector (E): A clamp or fitting used to secure a cable entering the junction box.
- Hole Saw: A circular saw attachment used to cut precise holes in materials like drywall.
- Ladder (G): A portable set of steps used to reach high places.
- Wire Strippers (H): A tool used to remove insulation from electrical wires.
Before You Start
Safety Information
To reduce the risk of fire, electric shock, or physical injury:
- ⚡ Turn off circuit breaker before installing this fixture.
- This product should be installed by a person familiar with the construction and operation of the product and the hazards involved. Safety eyeglasses ? and gloves ? are recommended.
- Abide by related regional and local laws or regulations.
- Proper grounding ? is required to ensure safety.
- Do not alter, relocate, or remove wiring during installation.
- Do not make or alter any open holes in wiring enclosure or electrical components during installation.
- Check for shipping damage ? before installing. If the product is damaged, do not use it.
- Keep fixture away from corrosive substances.
- Suitable for damp locations ? at temperatures ranging from -4°F to 113°F. Not for use where directly exposed to water ?.
- This product is not compatible with 3rd party sensors.
- This product is not compatible with photo controls.
- This product is not compatible with occupancy sensors.
- This product is not compatible with timing devices.
This device complies with Part 15 of the FCC rules ?. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference that may cause undesired operation. Please review all instructions carefully prior to installation.
⚠️ WARNING: Cancer & Reproductive Harm - www.P65Warnings.ca.gov
? Quickstart Guide
-
Step 1: Use template to cut hole.
(Diagram: A hand holds a circular installation template against a ceiling while a saw cuts a hole following the template's edge.) -
Step 2: Connect supply and luminaire wires.
(Diagram: Electrical wires are being connected using wire nuts inside an open junction box.) -
Step 3: Attach luminaire to junction box connector.
(Diagram: The luminaire's connector is being attached to the junction box.) -
Step 4: Insert luminaire into ceiling.
(Diagram: The slim downlight fixture is being pushed into a pre-cut hole in the ceiling.)
?️ Installation Guide
STEP 1: Cut Hole
a. Turn off the circuit breaker before installation.
b. Cut out the 6.33" housing size on Installation Template (C), then tape it onto the ceiling in the desired location.
c. Cut a ceiling hole using the Installation Template (C) as a guide.
Diagram: Shows a hand holding a template (C) against a ceiling, with a saw cutting a 6.33" hole.
STEP 2: Prepare Junction Box
a. Open the junction box (B) and remove the appropriate knockout.
Diagram: Shows an open junction box (B) with a knockout being removed.
STEP 3: Wiring
a. Thread the cable through the knockout, then secure the cable connector (E).
b. Connect the supply wires with the luminaire wires using the included wire nuts (D):
- Black to Black (Live)
- White to White (Neutral)
- Ground to Ground
Note: The supply ground wire may be bare copper, green, or yellow with a green stripe.
c. Tuck connected wires inside the junction box and close the cover.
Diagram: Shows wires (D) connecting through a cable connector (E) into a junction box (B).
Installation Guide (Cont.)
STEP 4: CCT Selection & Mounting
a. Slide the CCT Selection Switch to choose from five color temperatures.
b. Then, insert junction box (B) through ceiling hole:
- New Construction Applications: Secure to studs, joists, or similar fixed structural units.
- Remodel Applications: Securing to studs, joists, or similar fixed structural units is not required.
Diagram: Shows a CCT switch on the junction box (B) and the box being inserted into a ceiling hole.
STEP 5: Connect Luminaire
a. Attach luminaire to the junction box (B) using the connector (1).
b. Tighten the connector by hand (2).
Diagram: Shows the luminaire being connected to the junction box (B) via a connector.
STEP 6: Final Installation & Test
a. Push up the spring clips and insert the luminaire into the ceiling.
b. Turn on circuit breaker and test the light.
Diagram: Shows spring clips being pushed up and the luminaire being inserted into the ceiling.
STEP 7: Mode Selection & Reset
a. To toggle between downlight and nightlight mode, turn the wall switch off then back on within 2 seconds.
b. If some of the lights become unsynchronized, turn off the lights and wait at least 5 seconds. The lights will reset to downlight mode.
Diagram: Shows a hand operating a wall switch in an off-then-on sequence.
ℹ️ Product Details
Recommended Dimmers
| Brand | Model |
|---|---|
| LEVITON | 6672-1LW |
| LEVITON | 6674-10W |
| LEVITON | D26HD-2RW |
| LEVITON | DDMX1-BLZ |
| LUTRON | AYCL-153P-WH |
| LUTRON | CTCL-153PDH-WH |
| LUTRON | DVCL-153PR-WH |
| LUTRON | LGLC-153PLH |
Scan the QR code for the full compatible dimmer list.
Specifications
| Voltage | 120V |
| Wattage | 12W |
| Lumens | 1500 lm |
| Beam Angle | 120° |
| Efficacy | 117 lm/W |
| Housing Material | PC+Metal |
| Dimmable | Yes |
| Average Lifetime | 35,000 hrs |
| Power Factor | > 0.9 |
| Moisture Rating | Damp Rated |
| Power Source | Hardwired |
| CRI | 80+ |
| Usage | Indoor |
| Warranty | 7 Years |
❓ Common Troubleshooting
Feeling in the dark about an issue with your product? No worries! Our troubleshooting section is here to shed some light and provide you with easy-to-follow solutions for any problem.
If you still need some assistance, please feel free to contact Sunco support with any questions. Their team of lighting experts are happy to help brighten your day.
Installation Issues
| Problem | Solution |
|---|---|
| ? Light isn't turning on. | Double check if fixture is properly connected and circuit breaker hasn't been tripped. |
| ? Light unexpectedly fails. | For further assistance, reach out to customer support. |
Dimming Issues
| Problem | Solution |
|---|---|
| ? Light not dimming to lowest setting. | Ensure minimum dimmer load requirement is met. |
| ? Light not dimming smoothly. | Verify dimmer compatibility with fixture. |
| ? Light not compatible with dimmer switch. | Check light-dimmer compatibility. Consider purchasing compatible switch if necessary. |
⚡ Flickering Issues
| Problem | Solution |
|---|---|
| Light is flickering when turning on. | Check that fixture wiring connections are secure. |
| Light flickering with other lights on the same circuit. | Check that the lights on the same circuit are not overloading the circuit. |
| Light flickering when turned on. | Verify fixture compatibility and that it is grounded. |
| Light flickering when dimmed. | Verify dimmer switch compatibility. |
? Buzzing Issues
| Problem | Solution |
|---|---|
| Fixture buzzing with power outages. | Verify light is connected to surge protector securely. |
| Fixture buzzing with appliances or electronic devices. | Look for nearby interferences that can cause buzzing. Such as televisions, radios, computers, etc. |
| Fixture buzzing when dimmed. | Verify dimmer switch compatibility. |
P65Warnings.ca.gov
