Notice d'utilisation de la télécommande pour : 921829

Description du produit

This document provides instructions for the Resistex 921829 remote control, used for managing lighting fixtures with motion and daylight sensors.

The remote control features a display showing sensor status (PIR, PW), brightness levels (100%, 10%, 0%), and lux values. It includes buttons for power, mode selection, scene setting, programming, and advanced parameter adjustments.

Key Buttons and Display Elements:

• Display: Shows PIR status, PW status, brightness percentage (100%, 5%, 10%, 0%), and Lux levels.
• ON/OFF: ? [power] - Permanently turns the light on or off, disabling motion detection.
• MW/PIR: ? / ? [sensor type] - Switches between Microwave (MW) and Infrared (PIR) detection modes.
• Scene: ? [scene] - Resets all settings to default values.
• Start: ▶️ [start] - Initiates programming mode.
• Memory: ? [memory] - Saves the current programming settings.
• Apply: ✅ [apply] - Applies saved settings to another luminaire.
• Detection Range: ? [range] - Adjusts the motion sensor's detection area.
• Hold Time: ⏱️ [hold time] - Sets the duration the light stays on after detection.
• Stand-by Dimming: ? [dimming] - Sets the desired light level during the pre-warning period.
• Stand-by Period: ⏳ [period] - Sets the duration of the pre-extinction warning.
• Daylight Sensor: ☀️ [daylight] - Adjusts the ambient light level threshold for sensor activation.
• Test (2s): ? [test] - Verifies motion sensor functionality.
• Power %: ⚡ [power %] - Adjusts the light brightness level.
• UP/DOWN Arrows: ⬆️ / ⬇️ [up/down] - Navigate through settings.

Permanent and Automatic Modes

Press the ON/OFF ? button to permanently turn the luminaire on or off. In this mode, motion detection is disabled. Press the Scene ? or Apply ✅ button to exit this mode.

Press the MW/PIR ? / ? button to change the detection mode:

• MW corresponds to microwave detection.
• PIR corresponds to infrared detection.

Press the Scene ? button to reset all settings to default:

• Detection zone = 100%
• Hold time = 5s
• Pre-warning extinction = 10%
• Daylight sensor = disabled

Press the Power % ⚡ button followed by the UP ⬆️ or DOWN ⬇️ buttons to adjust the brightness level.

Advanced Settings

Adjusting Motion Sensor Detection Range:

Press the Detection Range ? button, then use the UP ⬆️ or DOWN ⬇️ buttons as needed. Four settings are available: 100%, 75%, 50%, and 25%.

Adjusting Luminaire Hold Time:

Press the Hold Time ⏱️ button, then use the UP ⬆️ or DOWN ⬇️ buttons as needed. Eight settings are available: 5s, 30s, 1min, 3min, 5min, 10min, 20min, and 30min.

Setting Desired Illumination Level During Pre-warning:

Press the Stand-by-dimming ? button, then use the UP ⬆️ or DOWN ⬇️ buttons as needed. Four settings are available: 10%, 20%, 30%, and 50%.

Setting Pre-extinction Warning Duration:

Press the Stand-by-dimming ⏳ button, then use the UP ⬆️ or DOWN ⬇️ buttons as needed. Nine settings are available: 0s, 10s, 30s, 1min, 5min, 10min, 30min, 60min, and +∞.

Adjusting Daylight Sensor Threshold:

Select the ambient light level suitable for your use by pressing the Daylight Sensor ☀️ button, then use the UP ⬆️ or DOWN ⬇️ buttons as needed. Twelve settings are available: Disable, 400lux, 350lux, 300lux, 250lux, 200lux, 120lux, 80lux, 50lux, 30lux, 10lux, and 2lux.

Programming Duplication

Before starting your programming, press the Start ▶️ button. Once this mode is activated, you can use all the settings explained in the "Advanced Settings" section.

When you have finished setting everything, press the Memory ? button. Your programming is now saved in the remote control.

Position yourself near another luminaire and press the Apply ✅ button. Your programming will be directly sent to the new luminaire. Repeat this step for each new luminaire.

Test Mode

Press the Test (2sec) ? button to verify the proper functioning of the motion sensor.