Speco Technologies

1 Warning and Caution

• Warning: If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself. Any unauthorized changes or modifications could void the warranty.
• Do not allow water or liquid intrusion into the camera.
• All installation and operation should conform to local electrical safety codes.
• Make sure the device is firmly installed on the wall or ceiling.
• Do not use the camera beyond the specified voltage range.
• Do not drop the camera or subject it to physical shock.
• Avoid touching the camera lens.
• If cleaning is necessary, please use a cleaning cloth to wipe it gently.
• Do not aim the camera at the sun or extremely bright light sources.
• Do not place the camera in extremely hot or cold environments, or dusty and damp locations. Do not expose it to highly electromagnetic radiation.
• Do not block any ventilations.

2 Package

The package includes the following items:

• Camera
• Quick start guide
• CD
• Drill template
• Screwdriver
• Tapping screw ×3
• Plastic plug ×3
• Rubber plug
• Junction box

3 Overview

The camera features the following connections and components:

• 1: Ethernet connector
• 2: Power connector
• 3: Mounting base
• 4: Fixed screw (for adjusting view angle)
• 5: Microphone
• 6: Micro SD card slot
• 7: Reset button

Diagram Description: The diagram shows the camera with labeled connectors: 1 Ethernet connector, 2 Power connector, 5 Microphone. The mounting base is labeled 3 Mounting base, with 4 Fixed screw. A separate view shows the rear of the camera with 6 Micro SD card slot and 7 Reset button.

4 Installation

Before you start, please make sure that the wall or ceiling is strong enough to withstand three times the weight of the camera and the junction box.

Step 1: Prepare Mounting Base and Junction Box

Open the mounting base and the upper cover of the junction box.

Diagram Description: Two separate components are shown: the mounting base and the upper cover of the junction box, both detached from the main camera unit.

Step 2: Install Junction Box

Install the junction box onto the wall or ceiling using the screws provided.

Diagram Description: The junction box is shown being attached to a flat surface (wall/ceiling) with screws.

Step 3: Insert Micro SD Card

Unscrew the cover from the dome to access the SD card slot. Insert a micro SD card. After that, install the cover back to the dome and fix it firmly with the screws. (Note that the cover should not be installed unevenly.)

Diagram Description: A view of the camera dome cover being removed, revealing the Micro SD card slot. An arrow indicates inserting a Micro SD card into the slot. The SD card slot cover is also shown.

Step 4: Mount Camera to Base

Mount the rubber plug to the gap of the mounting base and fasten the camera onto the mounting base.

Diagram Description: The camera is shown being attached to the mounting base. A rubber plug is positioned in a gap on the mounting base.

Step 5: Connect Cables and Reassemble

Route the cables through the cable hole and connect the cables (Ethernet and power). Then reinstall the upper cover onto the junction box.

Step 6: Adjust View Angle

Loosen the fixed screw to adjust the view angle of the camera. Before adjustment, preview the image of the camera on a monitor. After that, tighten the fixed screw to finish the installation.

Diagram Description: The camera is mounted, and a fixed screw is highlighted. An arrow indicates adjusting the camera's position.

5 Web Operation and Login

The IP Scanner utility can search for the device on the local network.

Operation Steps:

• 1: Make sure that the camera and the PC are connected to the same local network. The camera is set to DHCP by default.
• 2: Install the IP Scanner utility from the provided CD and run it after installation.
• 3: In the device list displayed by IP Scanner, you can view the IP address, model number, and MAC address of each device. Select the applicable device and double-click to open the web viewer. Alternatively, you can manually enter the IP address in the address bar of your web browser.

The login interface requires a username and password. The default username is 'admin' and the default password is '1234'. After logging in, follow the on-screen directions to install any necessary plugins.

Diagram Description: Screenshot of the 'SecureGuard IP Scanner' application displays a table with columns: Status, Open Web Page, Login..., Name, Model Name (O4DT1M), IP Address (e.g., 192.168.17.251), MAC Address, Wireless IP Address, Factory Default, Information, About. A separate image shows the Speco Technologies login page with fields for Username and Password, and Login/Cancel buttons.