Speco Technologies 08VT2 Quick Start Guide

Welcome

Thank you for purchasing this network camera! This owner's manual is designed to be a reference tool for your system. Please read this manual carefully before operating the unit and retain it for future reference. Should you require any technical assistance, contact Speco Technologies Tech Support at 1-800-645-5516.

Important Safeguards and Warning

1. Electrical Safety

All installation and operation should conform to local electrical safety codes. Use a certified/listed 12VDC Class 2 power supply only. Do not connect two power supplying sources to the device simultaneously, as this may result in device damage. The product must be grounded to reduce the risk of electric shock. Improper handling and/or installation could pose a risk of fire or electrical shock.

2. Environment

Heavy stress, violent vibration, or exposure to water is not allowed during transportation, storage, and installation. This product should be installed in a cool, dry place away from direct sunlight and heat sources. Do not install the product in extreme temperature conditions. Do not expose the camera to electromagnetic radiation, as this may result in CMOS sensor failure. Ensure no ventilation openings are blocked. Do not allow water and liquid intrusion into the camera.

3. Operation and Daily Maintenance

Shut down the device and unplug the power cable before performing any maintenance. Do not touch the CMOS sensor optic component. A blower can be used to clean dust from the lens surface. Always use a dry soft cloth to clean the device. If there is excessive dust, use a cloth dampened with a small quantity of neutral detergent, followed by a dry cloth. For enclosure cleaning, use a professional optical cleaning method. Improper cleaning methods may result in poor IR functionality or IR reflection. Grounding holes are recommended to be used to enhance camera reliability. The dome cover is an optical device; do not touch or wipe its surface directly during installation and use. If dirt is found on the dome cover:

• Stained with dirt: Use an oil-free soft brush or hair dryer to gently remove it.
• Stained with grease or fingerprint: Use an oil-free cotton cloth or paper soaked with alcohol or detergent. Wipe from the lens center outward, changing the cloth and wiping several times if necessary.

Warning

This camera should be installed by qualified personnel only. All examination and repair work should be performed by qualified personnel. Any unauthorized changes or modifications could void the warranty.

Statement

This guide is for reference only. Product, manuals, and specifications are subject to modification without prior notice. Speco Technologies reserves the right to make these modifications without incurring any obligation. Speco Technologies is not liable for any loss caused by improper operation.

Note

Before installation, check the package to ensure all components are included. Contact your representative or Speco customer service department immediately if something is broken or missing in the package.

1 Package

The package includes the following items:

• Camera
• Quick start guide
• Tapping screws × 3
• CD
• Drill template
• Plastic plug × 3
• Screwdriver
• Junction box

[Diagram Description: A layout showing the camera unit, a booklet labeled 'Quick start guide', three screws labeled 'Tapping screws x 3', a CD disc, a circular 'Drill template', three plastic plugs labeled 'Plastic plug x 3', a screwdriver, and a 'Junction box'.]

2 Overview

The camera features the following connectors and components:

• 1 Ethernet connector
• 2 Audio input connector
• 3 Power connector
• 4 Mounting base
• 5 Fixed screw
• 6 Microphone
• 7 Micro SD card slot
• 8 Reset button

[Diagram Description: A diagram illustrating the camera's rear and side view, with callouts pointing to numbered components: 1. Ethernet connector, 2. Audio input connector, 3. Power connector, 4. Mounting base, 5. Fixed screw, 6. Microphone, 7. Micro SD card slot, 8. Reset button. Another diagram shows a close-up of the Micro SD card slot and Reset button.]

[Diagram Description: A connection diagram showing the camera unit connecting to a water-proof connector, a DC12V power adapter, and an audio input device. The network cable is shown connecting to the camera. An illustration of a PoE switch or injector is also shown.]

Note 1: It is recommended to install the water-proof connector for outdoor installations.

Note 2: A DC 12V power supply is not required if a PoE switch or injector is used to power the camera.

Connecting Network Cable

Follow these steps to connect the network cable:

1. Step 1: Loosen the nut from the main element of the connector. [Diagram Description: Shows the connector nut being loosened.]
2. Step 2: Run the network cable (without RJ45 connector) through both elements of the connector. Then crimp the cable with an RJ45 connector. [Diagram Description: Shows the network cable passing through the connector parts, followed by an illustration of crimping an RJ45 connector onto the cable.]
3. Step 3: Connect the cable to the water-proof connector. Then tighten the nut and the main cover. [Diagram Description: Shows the completed connection of the network cable to the water-proof connector and tightening of the parts.]

3 Installation

Important: Before starting, ensure the wall or ceiling is strong enough to support three times the weight of the camera and the junction box.

Step 1: Open the mounting base and the upper cover of the junction box. [Diagram Description: Shows the mounting base and the upper cover of the junction box separated.]

Step 2: Install the junction box onto the wall using the provided screws. [Diagram Description: Illustrates the junction box being mounted to a ceiling or wall surface with screws.]

Step 3: Loosen the fixed screw to disassemble the camera. Remove the cover from the dome to insert the SD card. Reinstall the cover onto the dome and fix it firmly with screws. Ensure the cover is not installed unevenly. [Diagram Description: Shows the camera being disassembled by loosening a fixed screw. A view of the enclosure, dome, mounting base, and cover is presented. The process of inserting an SD card into the dome cover area is implied.]

Step 4: Fasten the mounting base of the camera onto the junction box. [Diagram Description: Shows the camera's mounting base being attached to the previously installed junction box.]

Step 5: Route the cables through the cable hole and connect them. Reinstall the upper cover onto the junction box and mount the dome and enclosure to the mounting base. [Diagram Description: Illustrates cables being passed through a hole, connected, and the camera assembly being secured to the mounting base.]

Step 6: Adjust the camera to obtain an optimum angle. Before final adjustment, preview the camera's image on a monitor. After confirming the angle, tighten the fixed screw to complete the installation. [Diagram Description: Shows the camera mounted, with an arrow indicating adjustment of the angle, and a callout pointing to the 'Fixed screw' that secures the position.]

4 Web Operation and Login

The IP Scanner can be used to search for the device on the local network.

Operation

1. Ensure the camera and the PC are connected to the same local network. The camera is set to DHCP by default.
2. Install the IP Scanner from the CD and run it after installation, or download it from https://www.specotech.com/ip-scanner/.

[Diagram Description: A screenshot of the 'SecureGuard IP Scanner' application interface is shown. It displays columns for Status, Model Name, Name, IP Address, MAC Address, Wireless IP Address, and Zero Config IP. The device '08VT2' is listed with an IP address '192.168.17.251' and MAC address '5C:F2:07:24:68:9A'. Buttons like 'Refresh', 'Open Web Page', 'Login', 'Restart', 'Factory Default', 'Information', and 'About' are visible.]

In the device list, you can view the IP address, model number, and MAC address of each device. Select the applicable device and double-click to open the web viewer. Alternatively, you can manually enter the IP address in the web browser's address bar.

[Diagram Description: A screenshot of the camera's login interface is shown. It features fields for 'Username' and 'Password', with 'Login' and 'Cancel' buttons.]

The login interface is displayed above. The default username is 'admin' and the password is '1234'. After logging in, follow the on-screen directions to install any required plugins.