Scosche NEXC1 Smart Dash Cam User Manual

Model: NEXC1

Introduction

This user manual provides comprehensive instructions for the Scosche NEXC1 Smart Dash Cam. Please read the entire manual before installation to familiarize yourself with the NEXC1.

Safety Instructions
NEXC1 Package Contents
Product Description
Memory Card
Camera Function Buttons
Camera Mounting
Power Cable Routing
Smartphone App
Connecting Camera to iPhone Devices
Connecting Camera to Android Devices
Troubleshooting

Safety Instructions & Legal Considerations

Avoid Legal Issues

Before installation, check all European, national, and local laws. It is the user's responsibility to comply with all applicable laws regarding the use of electronic devices while driving.

CAUTION!

Before installation, disconnect the negative terminal of the vehicle's battery to prevent electrical damage. Avoid routing cables near any airbags; airbags can deploy unexpectedly and cause serious injury or death.

General Safety Guidelines

Check the power cable and do not use it if it is damaged.
Do not mount the camera where it could obstruct the driver's view of the road or impede airbag deployment. Check local and state laws before connecting the NEXC1.
Clean the lens with a soft cloth, ensuring no dirt is present on the lens.
Prevent any contact of liquid or moisture with the device.
Do not expose the NEXC1 to open flame, as it may cause damage.
Keep out of reach of children.

Scosche Industries Inc. and Sunnysoft s.r.o. are not responsible for data loss during operation.

NEXC1 Package Contents

The NEXC1 is a WiFi Dash Cam featuring a wide-angle lens with a 140° field of view. It works with your smartphone and the Nexar app to record your drives. It saves important events to the Nexar Cloud, provides video recordings, and facilitates sending data to insurance companies in case of an accident.

Included items:

NEXC1 WiFi Dash Cam
Suction cup mount with cable
Camera with attached mount
Power USB cable and 24W dual USB charger (12W per port) for USB charging
3m USB power cable with 12V plugs for powering the NEXC1 camera

Cable Management Kit:

This kit helps route the power cable from the camera to a 12V socket or cigarette lighter socket.

Cleaning Wipes (1 wet, 1 dry)
Adhesive Cable Clips (4 pcs)
Zip Ties (5 pcs)
Adhesive Cable Clips (4 pcs)
Panel Removal Tool (1 pc)

Diagram shows the NEXC1 camera unit.

Diagram shows the power cable and dual USB charger.

Diagram shows the items included in the cable management kit.

Product Description

The NEXC1 dash cam features a 140° wide-angle lens with a 1080p Full HD Sony image sensor optimized for low-light conditions.

Camera Components:

1 - USB-C Power Connector: For connecting the power cable.
2 - Quick Release Socket: For attaching/detaching the camera from the mount.
3 - 140° Wide-Angle Lens: Captures a broad view of the road.
4 - LED Indicator:
- Off: Camera is powered off.
- Solid Red: Camera is on, not recording.
- Blinking Red: Camera is on and recording.
5 - Microphone: Records audio.
6 - Event Capture Button: A capacitive touch button to manually mark important events.
7 - Speaker: Outputs audio alerts or feedback.
8 - WiFi Connection Button: Used to initiate WiFi pairing.
9 - Power Button: Turns the camera on or off.
10 - microSD Card Slot: For inserting a memory card.

Diagrams show the front, back, bottom, and side views of the NEXC1 camera, with numbered components indicated.

Memory Card

Inserting a Memory Card

Insert the memory card into the designated slot with the gold contacts facing the rear of the camera body.
Push the memory card into the slot until it clicks into place.

Removing a Memory Card

Push the exposed edge of the memory card into the camera body until it clicks. Once released, the card will eject from the slot, allowing it to be removed.

CAUTION! Remove the memory card only when the device is powered off. Attempting to remove the card while the device is operating may cause damage to stored files or the memory card itself.

Diagram shows how to insert a microSD card into the camera slot.

Camera Function Buttons

A – WiFi Connection Button

Press this button to switch to wireless connection to the device.

B - Power Button

Long Press: Press and hold for more than 3 seconds to turn the device on or off.
Short Press: Press to start/stop recording.

C - Event Capture Button

After pairing the camera with your smartphone, the camera will automatically record. Use this button to mark events.

Diagram shows the camera with buttons labeled A (WiFi), B (Power), and C (Event Capture).

Camera Mounting

Window Mount Assembly

Insert the USB-C connector from the suction cup mount into the corresponding connector on the camera, as shown in the diagram.

Diagram shows the USB-C connector being inserted into the camera.

Mounting and Adjusting the Camera

Thoroughly clean and dry the area of the windshield where the mount will be attached.
Press the suction cup mount firmly against the windshield (A) and secure the suction cup by engaging the lever (B).
Note: For best results, ensure the lever (B) is released before attaching it to the windshield.

Diagram shows the suction cup mount being attached to the windshield, with points A and B indicated for pressure and lever engagement.

Power Cable Routing Solution

IMPORTANT! Read this before routing the cable.

To prevent potential damage to the power cable, mount and position the camera on the vehicle's windshield in the desired recording direction before connecting and routing the power cable.

Option 1: Cable Routing with Panel Removal

For vehicles without A-pillar airbags.

Thoroughly clean and dry the windshield area where the camera's suction cup will be attached.
Mount the camera assembly onto the windshield.
Plan your cable routing, as illustrated.
Using the panel removal tool, carefully remove necessary panels for your chosen cable route. Route the cable under the headliner trim.
Note: It is recommended to explore your vehicle beforehand to plan the installation.
Connect the power cable to the camera and then route the cable from the camera to the 12-volt power source. Use the adhesive rubber cable clips to secure the cable routing near the camera.
Reassemble the panels in reverse order, hiding any excess coiled cable.

Option 2: Cable Routing using Adhesive Cable Clips

For vehicles with A-pillar airbags.

Thoroughly clean and dry the windshield area where the camera's suction cup will be attached, and where the adhesive rubber cable clips will be affixed.
Mount the camera assembly onto the windshield.
Plan your cable routing, as illustrated.
Connect and route the cable from the camera to the 12-volt socket under the headliner, along the edge of the windshield and near the trim/panels.
Route the USB cable using the provided adhesive rubber clips, which will help secure the cable in its chosen location.

How to Route the Power Cable?

Adhesive Cable Clips

Use the adhesive rubber cable clips to route the cable from the camera to the 12V power source (recommended for Option 2), as shown in the previous illustration.

Diagram shows adhesive cable clips being used to route a cable.

Cable Management, Zip Ties, and Clips

Cable management for the USB cable prevents it from slipping under the headliner. Use the included zip ties and rubber clips to secure excess cable or to fasten it along existing vehicle cable routing.

Diagram shows a coiled USB cable with zip ties and clips for management.

Illustration shows two options for routing the power cable in a car interior, one involving panel removal and the other using clips.

Smartphone App

The Nexar app is available on the App Store and Google Play. The NEXC1 seamlessly integrates with the Nexar app. Download the app to record and capture events, access free cloud storage, get instant crash reporting, and more.

Connecting Camera to iPhone Devices

Download the Nexar app by scanning the QR code on the previous page or by searching for "Nexar" in the App Store. It is recommended to download the app when connected to a WiFi network.

Launch the downloaded app.
Follow the prompts to register and grant all necessary permissions.

Connecting the Camera to Your iPhone

Turn on the camera. The camera automatically turns on when the vehicle is started and turns off when the vehicle is turned off. You can also manually turn on the camera by pressing and holding the power button for more than 3 seconds.
On your iPhone (not included), enable WiFi in the settings.
Connect to the WiFi network named "Nexar WiFi" (NEXC1-5G).
Enter the password: 12345678.
Once the WiFi connection is established, complete your phone's setup.
Launch the Nexar app and tap the "Drive" button on the top of the screen to start recording.
Confirm that the video source on your phone is receiving input from the NEXC100 and not your phone's camera.

Note: You can verify the camera feed in two ways:

Cover your phone's camera lens and check if the camera's image appears on your smartphone's display.
Check if the camera icon ? is active in the app.

Diagram shows the dash cam mounted on the windshield, connected wirelessly to a smartphone.

Nexar App on Android Devices

The Nexar app is available on Google Play.

Download the Nexar app by scanning the QR code above or by searching for "Nexar" in Google Play. It is recommended to download the app when connected to a WiFi network.

Launch the downloaded app.
Follow the prompts to register and grant all necessary permissions.

Connecting Camera to Android Devices

Turn on the camera. The camera automatically turns on when the vehicle is started and turns off when the vehicle is turned off. You can also manually turn on the camera by pressing and holding the power button for more than 3 seconds.
Once the camera is on, launch the Nexar app on your phone.
Tap the Menu icon and select "Settings".
In the Settings menu, tap "External Camera".

Note: Once you select the external camera, your phone will begin pairing with the camera. This process may take a moment.